Front door weatherstrip kit. This kit is the primary seal for the door to the body. Set includes the door bottom and perimeter seals that attach to the body and the door edge weatherstrip that attaches to the door.
Retainer, windshield division bar molding. Inner and outer. With threaded brass core as original (molding not included). Two (2) piece set.
This swing-out windshield gasket is designed from the original part for superior fitment and seal. The seal mounts into the metal channel attached to the glass and creates a seal when the glass is pressed against the body of the vehicle. It has vulcanized, or bonded, ends which means no cutting or splicing is required for installation.
Welting, fender. Superior quality, proper construction of reinforced black vinyl over vinyl core, one and three eighths (1-3/8) inch wide. One fourth (1/4) inch bead, fifty (50) foot roll. Typically used to attach four (4) fenders to body. For twenty five
Welting, fender. Superior quality, proper construction of reinforced black vinyl over vinyl core, one and three eighths (1-3/8) inch wide, three sixteenths (3/16) inch, fifty (50) foot roll. Typically used to attach four (4) fenders to body. For twenty fi
Welting, fender, bright chrome vinyl, three sixteenths (3/16) inch bead, one and one half (1-1/2) inch width. Superior quality. Fifty (50) foot roll. Typically used to attach four (4) fenders to body. For twenty five (25) foot roll see #70-1101-44.
Bumper, front spring axle-to-frame.
Weatherstrip, door window scraper seal, inner and outer. Slides into grove on top of the door's window opening and wipes the glass when window is raised and lowered.
This swing-out windshield weatherstrip comes in an eleven foot (11') strip and mounts into the metal channel attached to the glass. The rubber slides into the T-groove and creates a seal when the glass is pressed against the body of the vehicle.
Cover, brake master cylinder filler and inspection hole. Metal core as original.
Cushion, overload spring bumper. Fully molded rubber part that installs in overload spring arm.
Bulb type seal, gravel shield-to-rear bumper, anti-squeak. Also used as a door weatherstrip for some makes and models. Twelve (12) foot strip.
Channel, flexible window run, un-beaded. Cloth covered mohair-lined type. Available in 6ft lengths.
Bumper, cab hold down bolts. Comes as a pair of two (2). Fully molded rubber. One and five eighths inch (1 5/8") outside diameter by three eighths inch (3/8") inside hole diameter by one and one thirty-two seconds inch (1 1/32") height. Chevrolet/GMC Tru
Grommet, steering column at floor.Length: 3.375 inches.
Welting, fender. Superior quality, proper construction of reinforced vinyl over vinyl core, one and three eighths (1-3/8) inch wide, black only. One fourth (1/4) inch bead, twenty five (25) foot roll. Typically used to attach two (2) fenders to body. For
Welting, fender, bright chrome vinyl, three sixteenths (3/16) inch bead, one and one half (1-1/2) inch width. Superior quality. Twenty five (25) foot roll. Typically used to attach two (2) fenders to body. For fifty (50) foot roll see our #70-1102-44.
Welting, fender. Superior quality, proper construction of reinforced black vinyl over vinyl core, one and three eighths (1-3/8) inch wide, three sixteenths (3/16) inch, twenty five (25) foot roll. Typially used for attaching two (2) fenders to body. For f
Gasket, cowl vent. These parts are made of the highest quality and authenticity.Length: 15.0 inches.
Anti-squeak, hood to cowl. Five eighths (5/8) inch by seven thirty seconds (7/32) inch. One eight (8) foot strip per vehicle.Length: 96.0 inches.
Seal, gearshift at floor. See our #60-0397-24 for 4 speed transmission.
Cushion, horn blowing button.Height: 1.0 inches.
Seal gearshift at floorboard. Sponge rubber, one half (1/2) inch thick. One required per vehicle.Length: 6.5 inches. Width: 6.5 inches. Height: .50 inches.
Seal, handbrake at floorboard. Rubber sponge, one (1) required per vehicle.Length: 4.50 inches. Width: 2.0 inches. Height: 1.25 inches.
Starter button, push on replacement to rod. Two (2) inch outside diameter.
Boot, brake master cylinder rod. Fits on one and one fourth (1-1/4) inch diameter cylinder. Height: 2.125 inches.
Bumper, brake and clutch pedal shank, rides under floorboard. One and one eighth (1-1/8) inch clearance for pedal shaft. Compare with our #60-0579-24.
Weatherstrip, lower door. Fastens to cab threshold. Two strips thirty six (36) inch long each.Length: 36.0 inches. Width: .4375 inches.
Grommet, firewall, oblong four (4) hole style. Fits steel retainer for throttle and choke cables, oil and temperature lines.
Wedge pads, door aligning.Length: 1.125 inches. Width: .5 inches. Height: .875 inches.
Cover, starter pedal button. Rubber slip over type for old metal. Two (2) inch outside diameter. If car doesn't have old metal, see our #60-0322-21.
Grommet, steering column to cowl, for U-bolt clamp. Brown rubber. For black see our #60-0012-36.Color:brown Height: 1.25 inches.
Grommet, steering column to cowl, for U-bolt clamp. Black rubber. For brown see our #60-0012-89.Height: 1.25 inches.
Cover, battery clamp. Control unsightly sulfate buildup. Help protect the nearby metal and finish. Good copy from original part.Length: 3.5 inches.
Bumper, clutch pedal shank under floorboard. Some commercial and utility models, compare with our #60-0104-24.
Ferrule, outside door handle. Chrome with rubber sleeve. Two (2) piece set includes one (1) chrome piece and one (1) rubber piece. Enough for one door.
Grommet for ignition switch conduit through firewall.
Grommet, wire harness through firewall.
Grommet, wiring harness through firewall, for one and one fourth (1-1/4) inch hole in sheet metal.Height: .75 inches.
Bellows, starter pedal shaft to floorboard. Three eighths (3/8) inch top hole with three (3) inch height.Width: 2.875 inches. Height: 3.0 inches.
Bushing, for shock absorber link cross pin or stabilizer link cross pin.1931-36 Bushing, rubber, for shock absorber link cross pin, #41151.
Bushing, gearshift shaft lever, larger type. Three eighths (3/8) inch inside diameter by nine sixteenths (9/16) inch outside diameter barrel.Height: .
Bumper, door side. Five eighths (5/8) inch by seven eighths (7/8) inch by one and seven sixteenths (1-7/16) inch. Two (2) door.
Bumper (stop), swing out windshield against dash. Steel core, nine sixteenths (9/16) inch diameter by five sixteenths (5/16) inch thick. Replaces #3681093. Two (2) per vehicle.
Bumper, front and rear body hinge pillar, one (1) inch diameter by one fourth (1/4) inch thick, held by screw, steel core. Auxiliary, used only where needed to prevent door rattle.Note: also used on 1942-50 Packards with Clipper styling near t
Grommet for outside door handle bezel.
Grommet, spark plug and coil wire at distributor cap outlets. For seven (7mm) millimeter, later years.
Pressure ring (washer), sponge rubber, interior door handle and window regulator escutcheon. One and three fourths (1-3/4) inches outside diameter by three eighths (3/8) inch thick.
Bushing, shock absorber arm link.
Mounting pad, continuous for lights, hinges, brackets, and other bright work when no molded pad is available. Available by the foot.