Mount, transmission support. Revulcanization service only.
This Front Door Weatherstrip Set is the primary seals for the Left and Right front doors to the body. Set includes the door bottoms and perimeter seals that attach to the body and the door edge weatherstrips that attaches to the Left and Right front doors.
This Rear Window gasket is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the back glass and has vulcanized, or bonded, ends which means no cutting or splicing is required for installation.
Retainer, windshield division bar molding. Inner and outer. With threaded brass core as original (molding not included). Two (2) piece set.
This Swing-Out Windshield Weatherstrip is designed from the original part. The seal mounts into the track (channel) attached to the glass that goes all the way around the windshield and creates a seal when the glass is pressed against the body of the vehicle.
Welting, fender. Superior quality, proper construction of reinforced black vinyl over vinyl core, one and three eighths (1-3/8) inch wide. One fourth (1/4) inch bead, fifty (50) foot roll. Typically used to attach four (4) fenders to body. For twenty five
Welting, fender, bright chrome vinyl, three sixteenths (3/16) inch bead, one and one half (1-1/2) inch width. Superior quality. Fifty (50) foot roll. Typically used to attach four (4) fenders to body. For twenty five (25) foot roll see #70-1101-44.
A superior quality Fender Welting material constructed of reinforced black vinyl over a vinyl core. Typically used for attaching four (4) fenders to body. Sold in a 50 foot roll.
Bumper, front spring axle-to-frame.
Weatherstrip, door window scraper seal, inner and outer. Slides into grove on top of the door's window opening and wipes the glass when window is raised and lowered.
Bumper, rear spring. Fits original retainer.Width: 2.5625 inches.
Grommet, front bumper. Fully molded rubber. Five and one fourths inch (5-1/4") outside length by two and one eighths inch (2-1/8") outside width by one and five eighths inch (1-5/8") inside hole length by seven sixteenths inch (7/16") inside hole width by
Grommets, rear bumper, right and left. Fully molded rubber. Three and three fourths inch (3-3/4") outside length by two and one sixteenth inch (2-1/16") outside width by one and three fourths inch (1-3/4") inside hole length by five sixteenths inch (5/16"
This Swing-Out Windshield Weatherstrip comes in an eleven (11') foot strip. The seal slides into the track (channel) attached to the glass that goes all the way around the windshield and creates a seal when the glass is pressed against the body of the vehicle.
Cover, brake master cylinder filler and inspection hole. Metal core as original.
Cushion, overload spring bumper. Fully molded rubber part that installs in overload spring arm.
This Rear Bumper Stone Deflector is a bulb type seal. Made of high-quality EPDM dense rubber and designed from original parts for superior fitment and seal. Twelve (12) foot strip.
Pad. hood corner, steel core as original, front and rear.Length: 1.5 inches.
Channel, flexible window run, un-beaded. Cloth covered mohair-lined type. Available in 6ft lengths.
This Headlight Door To Lens Ring seal pair is designed from the original part for superior fitment and function. The part works to seal between the headlight door housing and the headlight retaining ring. The part is a single lip type seal for sealed beam headlights.
Bumper, cab hold down bolts. Comes as a pair of two (2). Fully molded rubber. One and five eighths inch (1 5/8") outside diameter by three eighths inch (3/8") inside hole diameter by one and one thirty-two seconds inch (1 1/32") height. Chevrolet/GMC Tru
Grommet, steering column at floor.Length: 3.375 inches.
Welting, fender. Superior quality, proper construction of reinforced vinyl over vinyl core, one and three eighths (1-3/8) inch wide, black only. One fourth (1/4) inch bead, twenty five (25) foot roll. Typically used to attach two (2) fenders to body. For
Welting, fender, bright chrome vinyl, three sixteenths (3/16) inch bead, one and one half (1-1/2) inch width. Superior quality. Twenty five (25) foot roll. Typically used to attach two (2) fenders to body. For fifty (50) foot roll see our #70-1102-44.
A superior quality Fender Welting material constructed of reinforced black vinyl over a vinyl core. Typically used for attaching two (2) fenders to body. Sold in a 25 foot roll.
Gasket, cowl vent. These parts are made of the highest quality and authenticity.Length: 15.0 inches.
Seal, gearshift at floor. See our #60-0397-24 for 4 speed transmission.
Seal gearshift at floorboard. Sponge rubber, one half (1/2) inch thick. One required per vehicle.Length: 6.5 inches. Width: 6.5 inches. Height: .50 inches.
This Hood to Cowl Weatherstrip installs at the rear of the engine bay to seal between the hood and vehicle body cowl. Sold as a pair for left and right side.
Seal, handbrake at floorboard. Rubber sponge, one (1) required per vehicle.Length: 4.50 inches. Width: 2.0 inches. Height: 1.25 inches.
Starter button, push on replacement to rod. Two (2) inch outside diameter.
Boot, brake master cylinder rod. Fits on one and one fourth (1-1/4) inch diameter cylinder. Height: 2.125 inches.
Bushing, link, front stabilizer shaft support. Molded rubber with heavy duty metal sleeve. Six (6) required per vehicle. One and one eighths inch (1 1/8") outside diameter by one half inch (1/2") inside hole diameter by one and one eighths (1 1/8") height
Bumper, brake and clutch pedal shank, rides under floorboard. One and one eighth (1-1/8) inch clearance for pedal shaft. Compare with our #60-0579-24.
Weatherstrip, lower door. Fastens to cab threshold. Two strips thirty six (36) inch long each.Length: 36.0 inches. Width: .4375 inches.
Grommet, firewall, oblong four (4) hole style. Fits steel retainer for throttle and choke cables, oil and temperature lines.
Wedge pads, door aligning.Length: 1.125 inches. Width: .5 inches. Height: .875 inches.
Cover, starter pedal button. Rubber slip over type for old metal. Two (2) inch outside diameter. If car doesn't have old metal, see our #60-0322-21.
Grommet, steering column to cowl, for U-bolt clamp. Brown rubber. For black see our #60-0012-36.Color:brown Height: 1.25 inches.
Grommet, steering column to cowl, for U-bolt clamp. Black rubber. For brown see our #60-0012-89.Height: 1.25 inches.
Cover, battery clamp. Control unsightly sulfate buildup. Help protect the nearby metal and finish. Good copy from original part.Length: 3.5 inches.
This Ferrule And Grommet Set for the outside door handle is cadmium plated ferrule with rubber sleeve. Two (2) piece set for one (1) door.
Bumper, clutch pedal shank under floorboard. Some commercial and utility models, compare with our #60-0104-24.
Ferrule, outside door handle. Chrome with rubber sleeve. Two (2) piece set includes one (1) chrome piece and one (1) rubber piece. Enough for one door.
Grommet, parking light wiring harness through fender.Length: 3.25 inches.
Grommet for ignition switch conduit through firewall.
Grommet, wire harness through firewall.
Grommet, wiring harness through firewall, for one and one fourth (1-1/4) inch hole in sheet metal.Height: .75 inches.
Bellows, starter pedal shaft to floorboard. Three eighths (3/8) inch top hole with three (3) inch height.Width: 2.875 inches. Height: 3.0 inches.
Gasket, parking light lens. One and one half (1-1/2) inch by four (4) inch.1941: All commercial and utility 1942: Most models Length: 4.0 inches.