Please click on the part name in red in order to get a complete description.
Separator, horn contact. For standard or non-flexible wheel.
Hose, cowl vent drain. Seems to be correct for some models rather than our #50-0259-54.
Pad and cushion set, horn blowing ring. Three (3) piece set.
Mounting pad, license light. Three and one eighth (3-1/8) inch by eight and seven eighths (8-7/8) inch. Fully detailed.Length: 8.875 inches.
Weatherstrips, lower door. Set of three (3) pieces. Use full length for front doors, cut third piece in half to complete installation for both rear doors.
Gasket, license light lens. Fully molded with proper details.Length: 3.0 inches. Width: 1.6875 inches.
Grommets, brake and clutch pedal shank below floorboard.
Sash channel, side window glass. U-shaped steel channel only, no filler. Will require that you attach your own window regulator cam to underside as required.
Mounting pads, back up lights, elliptic, sharp beaded edge. One and five sixteenths (1-5/16) inch by two and seven eighths (2-7/8) inch.Length: 2.
Bushing, steering gear lever ball stud (Pitman arm). Originally made in one piece as spool bushing, but replacements made in halves.
Gasket, cowl vent. Perfect copy of original, not a sponge substitute, top quality material.
Gaskets, license light body to back plate. Two (2) per car.
Seal, brake and clutch pedal shank to floorboard. One and one half (1-1/2) inch by two and one eighth (2-1/8) inch by three fourths (3/4) inch thick.
Retainer (rubber), outer windshield, stainless center post molding. Use with original stainless molding and clips.
Lacing, hood cowl. Forty nine (49) inches long. Cloth anti-squeak material where hood rests on cowl. Includes tacks.
Grommet, fuel filler neck.
Front coil spring pad
Cushion ring, horn button contact, upper.
Boot, steering column vacuum cylinder. Excellent duplicate of original. Made of durable, long lasting rubber.Length: 5.50 inches.
Nipple, coil wire to distributor at coil end.
Gasket, cowl vent. These parts are made of the highest quality and authenticity.Length: 15.0 inches.
Pad, convertible top assembly. Rubber only, cements to original metal core.
Pad, rear license light body.Length: 7.0 inches. Width: 3.375 inches.
Channel, rigid run, lower side window below beltline, zinc plated steel with black cloth lining, one half (1/2) inch deep by one half (1/2) inch wide, fifteen (15) inches long.
Mount, radio antenna wire, under runningboard. Found on several models with factory type antennas that mount under the runningboard.
Gasket, taillight housing. Also order #70-0471-15 for the taillight mounting pad, and for the taillight lens gasket order #70-0658-15.Length: 8.25 inches.
Anti-squeak, hood to cowl. Five eighths (5/8) inch by seven thirty seconds (7/32) inch. One eight (8) foot strip per vehicle.Length: 96.0 inches.
Pad, roof mounted antenna gasket. Models with antenna mounted above center of windshield.
Pads, parking light.
Plugs, door bottom, self-retaining, oval.
Anti-squeak, hood ledge (cowl). One (1) pair required per car.Length: 25.5 inches. Width: .625 inches. Height: .21875 inches.
Weatherstrip, door lock, front and rear. Protects door lock mechanism from dust and weather.Length: 3.625 inches.
Grommet, firewall, main wiring harness plus up to five (5) accessory wires.
This trunk weatherstrip is designed from the original part for superior fitment and seal. The seal mounts on the lower length of the trunk directly to the body.
Channel, side window glass, vertical run. (Use our #40-0280-57 across top).
Fender welting. Thirty (30) foot roll. Black, textured finish. 1/4" bead.
Seal, gearshift at floor. See our #60-0397-24 for 4 speed transmission.
Bushing, rear axle track bar. Made in halves for easier replacement. Sold in pairs, two (2) pair needed per bar.Height: .75 inches.
Retainer, for outside windshield center post stainless molding. Use with original stainless molding and clips.Length: 15.5 inches. Width: 1.25 inches.
Pad, starter button. Made with brown rubber like original.
Seals, back of front fender to cowl.
Grommets, top motor to firewall bracket. Three (3) piece set.
Grommets, front bumper arms to splash pan rubber. Four (4) piece set.
Seal, rear bumper to stone deflector rubber.
Kit, motor mount. Enough for one motor mount. Kit includes one (1) each of 78-6029-A, B-6038-C, 78-6048-A, B-6039-A, and B-6047.
Grommets, runningboard to frame and front fender to cowl. Rubber grommets and metal washers. Twenty four (24) piece set.
Shackle set, spring. Front. Original steel stud type.
Seal gearshift at floorboard. Sponge rubber, one half (1/2) inch thick. One required per vehicle.Length: 6.5 inches. Width: 6.5 inches. Height: .50 inches.
Bumper, rear bumper deflector. Two (2) per car.Chevrolet 1942-55 Bumper, rubber, radiator grille, lower panel.Length: 2.1875 inches.
Pad, rear license light and trunk handle body.Length: 7.50 inches.
Tape, black bowdrill cloth. Adhesive backed, used to create cloth cover surface for side rail weatherstrips typically. Five (5) inches by five (5) foot roll. Pressure sensitive, for covering convertible side window weatherstrip such as our #70-1170-99 or
Insulator (hanger) tailpipe to frame. See also our #70-0600-13.Length: 3.9375 inches. Width: 1.9375 inches.
Mounting pads, trunk hinge. Four (4) piece set.Length: 8.8125 inches.
Boot, gearshift on steering column. Brown rubber. For black see our #30-0069-36. Two and one eighth (2-1/8) inch long style.
This trunk weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the trunk directly to the body.
Grommet, brake and clutch pedal floor seal.Width: 1.8125 inches. Height: 2.375 inches.
Mounting pad, trunk handle escutcheon.Length: 6.75 inches.
Filler valance or deflector, rear. Eight (8) inches long (cut shorter where required), three (3) to four (4) required per car.
Grommet, fuel filler neck with proper retaining flange. Oval style. Three and three fourths inch (3-3/4) outside width by four and one half inch (4-1/2") outside length by three fourths (3/4") inch height. Two and one sixteenth inch (2 1/16") top hole wi
Boot, parking light socket.
Seal, accelerator rod through floorboard.
Anti-squeak, hood to cowl, two (2) piece set for right and left.Length: 38.0 inches. Width: .625 inches. Height: .21875 inches.
Gasket, license lamp assembly.Length: 5.3125 inches.
Seal, handbrake at floorboard. Rubber sponge, one (1) required per vehicle.Length: 4.50 inches. Width: 2.0 inches. Height: 1.25 inches.
Pads, brake and clutch pedal. Concentric circle design.
Weather deflector, edge of folding top fabric near folding post, mounted on body.Length: 1.75 inches. Width: .625 inches.
Grommet, firewall, for throttle cable, wiper vacuum line and cowl vent drain hole. Three (3) holes (9/16", 3/8", 1/4").
Bushings, stabilizer bar. Front.
Grommets, license light wire. Two (2) per car.
Grommet, speedometer cable through firewall. Retained by steel collar (not included). Two and one half (2-1/2) inch outside diameter.
Gasket, taillight lens.Length: 5.125 inches. Width: 1.875 inches.
Pad, brake and clutch pedal. Black rubber. For brown see our part #50-0054-89. Perfect copy, fine detail.Width: 3.125 inches. Height: 2.125 inches.
Grommet, firewall, for speedometer cable, oil tube, temp. tube, 3 holes (5/16", 1/4", 3/16").
Door edge weatherstrip. This part is the primary door to body weatherstrip. Includes enough to do front, top and backside of one door.
Starter button, push on replacement to rod. Two (2) inch outside diameter.
Gasket, cowl vent.
Pad, deck handle base.
Boot, brake master cylinder rod. Fits on one and one fourth (1-1/4) inch diameter cylinder. Height: 2.125 inches.
Insulators, front coil spring. Fabric reinforced rubber as original.
Bushing, link, front stabilizer shaft support. Molded rubber with heavy duty metal sleeve. Six (6) required per vehicle. One and one eighths inch (1 1/8") outside diameter by one half inch (1/2") inside hole diameter by one and one eighths (1 1/8") height
Bumper, brake and clutch pedal shank, rides under floorboard. One and one eighth (1-1/8) inch clearance for pedal shaft. Compare with our #60-0579-24.
Boot, gearshift on steering column. Black rubber. For brown see our #30-0069-89. Two and one eighth (2-1/8) inch long style.Length: 2.25 inches.
Boot, starter solenoid.
Grommet, firewall, plain (no holes), for various uses.
Grommet, firewall, vacuum operated radio antenna lines.
Pad, starter pedal. Original pattern, brown rubber, exact copy.Height: .50 inches.
Boot, gear shift. Taupe.
Pedal, accelerator. Original type.
Bumper kit, hood.
Channel, quarter window glass to stainless frame rubber.
Gasket, outside door handle. Precision die cut from one thirty seconds (1/32) inch dense rubber to fit original factory handles.
Seal, starter through floorboard.
Insulator, exhaust system, muffler pipe bracket. Also intermediate pipe bracket on extra-long body styles. Two (2) required per car, most models.
Grommet, wire harness-thru-firewall mat. Two (2) inch diameter with two and one fourth (2-1/4) inch outside diameter flange.
Gasket, divided windshield center post. Combines inner and outer gasket in one piece as original. Seventeen (17) inch to (20) inch lengths.Length: 20.
End nut, check link (rubber bar with steel bar insert). Three fourths (3/4) inch by three fourths (3/4) inch by two (2) inch threaded five sixteenths (5/16) inch. (For round stop nut, see our #70-0326-70).
Bushing, shock absorber arm. Restore proper shock action.Height: 1.375 inches.
Seal, steering column tube. Installs under floor mat.
Seal, steering column at toe board, for steering column housing and shifter control shaft jacket. Top quality sponge rubber, accurately cut.