Stabilizer Bar End Link Set
p/n: 60-0221-33
Twenty-two (22) piece Stabilizer Bar End Link set for both sides of one (1) vehicle, fits front or rear bar. Order two (2) sets for vehicles with front and rear stabilizer bars. Hex head bolt 3/8"-16 NF x 6-15/16" long. Comes with metal sleeve, metal cup washers and rubber grommets.
Starter Button
p/n: 60-0322-21
Starter button, push on replacement to rod. Two (2) inch outside diameter.
Starter Button Cover
p/n: 60-0166-21
Cover, starter pedal button. Rubber slip over type for old metal. Two (2) inch outside diameter. If car doesn't have old metal, see our #60-0322-21.
Starter Pedal Bellows
p/n: 60-0210-21
Bellows, starter pedal shaft to floorboard. Three eighths (3/8) inch top hole with three (3) inch height.Width: 2.875 inches. Height: 3.0 inches.
Steering Column Gearshift Vacuum Boot
p/n: 60-0555-24
This Steering Column Vacuum Cylinder Boot is designed from the original part for superior fitment, finish and function. An excellent duplicate of original.
Steering Column Grommet - Black
p/n: 60-0621-36
This black rubber Steering Column To Toe Board Grommet is designed from the original part for superior fitment and sealing. Part is molded from quality rubber to authentic original dimensions.
Steering Column Grommet - Brown
p/n: 60-0621-89
This brown rubber Steering Column To Toe Board Grommet is designed from the original part for superior fitment and sealing. Part is molded from quality rubber to authentic original dimensions.
Steering column seal
p/n: 60-0478-36
Seal, steering column at toe board, for steering column housing and shifter control shaft jacket. Top quality sponge rubber, accurately cut.
Steering Gear Pitman Arm Bushing
p/n: 60-0105-36
This Steering Gear Pitman Arm Bushing is designed from the original part for superior fitment and function. Fully molded with steel core.
Steering knuckle support seal
p/n: 60-0089-32
Seal, steering knuckle support, upper. Four (4) per car.
Taillight Lens Gasket
p/n: 60-0100-15
Gasket, taillight lens.Length: 5.125 inches. Width: 1.875 inches.
Taillight Mounting Pad
p/n: 60-0008-15
Mounting pads, taillight. Length: 6.50 inches. Width: 2.6875 inches.
Transmission Mount Service
p/n: 60-0407-25
Insulator (support), transmission mounting. Revulcanization service only.Length: 7.0625 inches.
Transmission Support Mount - Revulcanization Service Only
p/n: 60-0530-25
Insulator - Plate Assembly - Guide for transmission support bracket. This Revulcanization Service Only is designed to restore your transmission mount to a like new original condition. Please call or email for more service details and ordering.
Trunk handle bezel and grommet
p/n: 60-0526-87
Bezel and grommet, trunk handle and license light body.
Trunk Hinge Mounting Pad
p/n: 70-1231-87
Mounting pads, trunk hinge. Four (4) piece set.Length: 8.8125 inches.
Trunk Weatherstrip
p/n: 70-0988-84
This Trunk Weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the trunk directly to the body.
Vent Window Division Post Weatherstrips
p/n: 60-0494-56
This front door Vent Window Division Post Weatherstrip pair is designed from the original part for superior fitment and seal. Fully molded rubber with metal core and attaching tabs.
Window Channel Retaining Clip
p/n: 70-0515-62
Clip, side window run channel retaining. Rust resistant spring steel.
Window Channel Retaining Clip
p/n: 70-0514-62
Clip, side window run channel retaining. Rust resistant spring steel. Compare with your original.
Window Felt Beltline Weatherstrips
p/n: 70-0555-58
These Window Felt Beltline Weatherstrips are sold as a three (3) foot pair. The beltline is used for side windows inner and/or outer, front and/or rear doors. Available in a 3ft pair.
Window Pinchweld Seal
p/n: 70-0096-52
This twelve (12) foot Window Pinchweld Seal is designed from the original part for superior fitment and function. The part is used to seal and retain an outer decorative reveal molding. Used with our 70-1192-52.
Window Stop Stem Bumper
p/n: 33-0622-62
This Window Stop Stem Bumper is fully molded and designed from the original part for superior fitment and seal. This bumper is made from high-quality EPDM dense rubber to provide excellent durability.
Windshield Division Bar Gasket
p/n: 70-0372-51
This Windshield Division Bar Gasket is designed from the original part for superior fitment and seal. Part is properly sized with "H" section. Part requires fitting to top and bottom, as it is not drilled.