Search Results
Transmission mount service
p/n: 60-0647-24
Mount, transmission support. Revulcanization service only.
Front Door Weatherstrip Kit
p/n: 90-0151-72
Front door weatherstrip kit. This kit is the primary seal for the door to the body. Set includes the door bottom and perimeter seals that attach to the body and the door edge weatherstrip that attaches to the door.
Windshield division bar gasket
p/n: 60-0128-52
Retainer, windshield division bar molding. Inner and outer. With threaded brass core as original (molding not included). Two (2) piece set.
Windshield Weatherstrip
p/n: 60-0447-50
This swing-out windshield gasket is designed from the original part for superior fitment and seal. The seal mounts into the metal channel attached to the glass and creates a seal when the glass is pressed against the body of the vehicle. It has vulcanized, or bonded, ends which means no cutting or splicing is required for installation.
Fender welting 1/4" bead 50ft
p/n: 70-1098-44
Welting, fender. Superior quality, proper construction of reinforced black vinyl over vinyl core, one and three eighths (1-3/8) inch wide. One fourth (1/4) inch bead, fifty (50) foot roll. Typically used to attach four (4) fenders to body. For twenty five
Fender welting 3/16 bead 50ft
p/n: 70-1100-44
Welting, fender. Superior quality, proper construction of reinforced black vinyl over vinyl core, one and three eighths (1-3/8) inch wide, three sixteenths (3/16) inch, fifty (50) foot roll. Typically used to attach four (4) fenders to body. For twenty fi
Fender welting 50ft chrome
p/n: 70-1102-44
Welting, fender, bright chrome vinyl, three sixteenths (3/16) inch bead, one and one half (1-1/2) inch width. Superior quality. Fifty (50) foot roll. Typically used to attach four (4) fenders to body. For twenty five (25) foot roll see #70-1101-44.
Side Window scraper seal
p/n: 60-0566-58
Weatherstrip, door window scraper seal, inner and outer. Slides into grove on top of the door's window opening and wipes the glass when window is raised and lowered. Customer will have to trim to length for proper fit. Four (4) piece set.
Rear spring bumper
p/n: 60-0137-32
Bumper, rear spring. Fits original retainer.Width: 2.5625 inches.
Front bumper grommet
p/n: 60-0045-28
Grommet, front bumper. Fully molded rubber. Five and one fourths inch (5-1/4") outside length by two and one eighths inch (2-1/8") outside width by one and five eighths inch (1-5/8") inside hole length by seven sixteenths inch (7/16") inside hole width by
Rear bumper grommet
p/n: 60-0127-28
Grommets, rear bumper, right and left. Fully molded rubber. Three and three fourths inch (3-3/4") outside length by two and one sixteenth inch (2-1/16") outside width by one and three fourths inch (1-3/4") inside hole length by five sixteenths inch (5/16"
Swing-out Windshield Weatherstrip
p/n: 40-0018-52
This swing-out windshield weatherstrip comes in an eleven foot (11') strip and mounts into the metal channel attached to the glass. The rubber slides into the T-groove and creates a seal when the glass is pressed against the body of the vehicle.
Rear Window Gasket
p/n: 60-0082-83
This rear window gasket weatherstrip set contains the rear window gasket itself and the locking strip. Both strips comes in a ninety inch (90") piece and mount around the full perimeter of the back glass. The ends may require trimming and bonding for installation.
Access hole plug
p/n: 60-0016-24
Cover, brake master cylinder filler and inspection hole. Metal core as original.
Axle rebound pad
p/n: 70-2301-32
Cushion, overload spring bumper. Fully molded rubber part that installs in overload spring arm.
Body Anti-Squeak Rubber
p/n: 60-0054-73
Bulb type seal, gravel shield-to-rear bumper, anti-squeak. Also used as a door weatherstrip for some makes and models. Twelve (12) foot strip.
Headlight Door To Lens Seal
p/n: 70-0389-14
Headlight door to lens seal. Molded without wire. Single lip type for sealed beams.
Cab bumper
p/n: 60-0510-48
Bumper, cab hold down bolts. Comes as a pair of two (2). Fully molded rubber. One and five eighths inch (1 5/8") outside diameter by three eighths inch (3/8") inside hole diameter by one and one thirty-two seconds inch (1 1/32") height. Chevrolet/GMC Tru
Fender welting 1/4" bead 25ft
p/n: 70-1097-44
Welting, fender. Superior quality, proper construction of reinforced vinyl over vinyl core, one and three eighths (1-3/8) inch wide, black only. One fourth (1/4) inch bead, twenty five (25) foot roll. Typically used to attach two (2) fenders to body. For
Fender welting 25ft chrome
p/n: 70-1101-44
Welting, fender, bright chrome vinyl, three sixteenths (3/16) inch bead, one and one half (1-1/2) inch width. Superior quality. Twenty five (25) foot roll. Typically used to attach two (2) fenders to body. For fifty (50) foot roll see our #70-1102-44.
Fender welting 3/16 bead 25ft
p/n: 70-1099-44
Welting, fender. Superior quality, proper construction of reinforced black vinyl over vinyl core, one and three eighths (1-3/8) inch wide, three sixteenths (3/16) inch, twenty five (25) foot roll. Typially used for attaching two (2) fenders to body. For f
Flexible Run Channel
Cloth covered mohair-lined type. For sides and top of side windows. Available in 5ft and 6ft lengths.
Cowl vent gasket
p/n: 60-0081-54
Gasket, cowl vent. These parts are made of the highest quality and authenticity.Length: 15.0 inches.
Hood to cowl weatherstrip
p/n: 60-0056-42
Anti-squeak, hood to cowl. Five eighths (5/8) inch by seven thirty seconds (7/32) inch. One eight (8) foot strip per vehicle.Length: 96.0 inches.
Gearshift seal
p/n: 60-0471-24
Seal, gearshift at floor. See our #60-0397-24 for 4 speed transmission.
Gearshift seal
p/n: 60-0397-24
Seal gearshift at floorboard. Sponge rubber, one half (1/2) inch thick. One required per vehicle.Length: 6.5 inches. Width: 6.5 inches. Height: .50 inches.
Handbrake seal
p/n: 60-0396-24
Seal, handbrake at floorboard. Rubber sponge, one (1) required per vehicle.Length: 4.50 inches. Width: 2.0 inches. Height: 1.25 inches.
Starter button
p/n: 60-0322-21
Starter button, push on replacement to rod. Two (2) inch outside diameter.
Brake master cylinder boot
p/n: 60-0180-24
Boot, brake master cylinder rod. Fits on one and one fourth (1-1/4) inch diameter cylinder. Height: 2.125 inches.
Brake And Clutch Pedal Bumper
p/n: 60-0104-24
Bumper, brake and clutch pedal shank, rides under floorboard. One and one eighth (1-1/8) inch clearance for pedal shaft. Compare with our #60-0579-24.
Firewall grommet
p/n: 60-0010-45
Grommet, firewall, oblong four (4) hole style. Fits steel retainer for throttle and choke cables, oil and temperature lines.
Door alignment pad
p/n: 70-1821-71
Wedge pads, door aligning.Length: 1.125 inches. Width: .5 inches. Height: .875 inches.
Starter button cover
p/n: 60-0166-21
Cover, starter pedal button. Rubber slip over type for old metal. Two (2) inch outside diameter. If car doesn't have old metal, see our #60-0322-21.
Brown steering column cushion
p/n: 60-0012-89
Grommet, steering column to cowl, for U-bolt clamp. Brown rubber. For black see our #60-0012-36.Color:brown Height: 1.25 inches.
Steering column cushion
p/n: 60-0012-36
Grommet, steering column to cowl, for U-bolt clamp. Black rubber. For brown see our #60-0012-89.Height: 1.25 inches.
Battery clamp cover
p/n: 70-0095-21
Cover, battery clamp. Control unsightly sulfate buildup. Help protect the nearby metal and finish. Good copy from original part.Length: 3.5 inches.
Ferrule and grommet kit
p/n: 70-0597-69
Ferrule and grommet set, outside door handle. Cadmium plated ferrule with rubber sleeve. Two (2) piece set for one (1) door.
Clutch pedal bumper
p/n: 60-0355-24
Bumper, clutch pedal shank under floorboard. Some commercial and utility models, compare with our #60-0104-24.
Door Handle Ferrule
p/n: 60-0389-69
Ferrule, outside door handle. Chrome with rubber sleeve. Two (2) piece set includes one (1) chrome piece and one (1) rubber piece. Enough for one door.
Firewall grommet
p/n: 60-0057-21
Grommet, wiring harness through firewall, for one and one fourth (1-1/4) inch hole in sheet metal.Height: .75 inches.
Starter pedal bellows
p/n: 60-0210-21
Bellows, starter pedal shaft to floorboard. Three eighths (3/8) inch top hole with three (3) inch height.Width: 2.875 inches. Height: 3.0 inches.
Shock and stabilizer bushing
p/n: 50-0220-32
Bushing, for shock absorber link cross pin or stabilizer link cross pin.1931-36 Bushing, rubber, for shock absorber link cross pin, #41151.
Gearshift bushing
p/n: 60-0237-24
Bushing, gearshift shaft lever, larger type. Three eighths (3/8) inch inside diameter by nine sixteenths (9/16) inch outside diameter barrel.Height: .
Door bumper
p/n: 60-0048-71
Bumper, door side. Five eighths (5/8) inch by seven eighths (7/8) inch by one and seven sixteenths (1-7/16) inch. Two (2) door.
Windshield bumper
p/n: 34-0258-52
Bumper (stop), swing out windshield against dash. Steel core, nine sixteenths (9/16) inch diameter by five sixteenths (5/16) inch thick. Replaces #3681093. Two (2) per vehicle.
Door bumper
p/n: 34-0025-42
Bumper, front and rear body hinge pillar, one (1) inch diameter by one fourth (1/4) inch thick, held by screw, steel core. Auxiliary, used only where needed to prevent door rattle.Note: also used on 1942-50 Packards with Clipper styling near t
