Body to Frame Webbing
p/n: 20-1599-48
This Body to Frame Webbing is designed from the original part for superior fitment and function. This webbing is used to shim the body to the frame. Also used as a noise reducer material. Webbing is two (2) inch wide, twenty-five (25) foot long roll.
Channel Filler Weatherstrip
p/n: 20-1633-62
Seal, door glass and stainless frame special. Top, bottom, and sides for one door.Width: .375 inches. Height: .625 inches.
Choke, Throttle and Starter Wiper Motor Grommet
p/n: 20-1561-20
This Choke, Throttle or Wiper Motor Grommet is designed from the original part for superior fitment and usage. A multi-purpose grommet, it fits into the vehicles firewall to provide a secure passthrough for the mechanical choke, throttle rod or wiper motor wiring.
Clutch and Brake Pedal Arm Seals
p/n: 20-1564-23
This Clutch and Brake Pedal Arm Seal pair is designed from the original part for an authentic fit, finish, and appearance. For Clutch and Brake pedal arms to floorboard.
Clutch and Brake Pedal Pads
p/n: 20-1563-22
This reproduction Clutch and Brake Pedal Pad pair screws to the pedal arms for a precise, factory fit. With authentic concentric circle design, pads are a perfect reproduction to replace worn original pedal pads.
Convertible Roof Rail Weatherstrip
p/n: 20-1636-65
This Convertible Roof Rail Weatherstrip is designed from the original part for superior fitment and seal. This window channel seal fits between windshield posts and door. Also fits along the top irons. This part is one (1) each. Five (5) individual pieces are required for the complete top.
Cowl Firewall Grommet
p/n: 20-1560-20
This Cowl Firewall Grommet fits into the upper section of the firewall for the main wiring harness. Also used to run the dash wires on the firewall and through the firewall.
Cowl Lacing Rubber Seal
p/n: 20-1587-42
This Cowl Lacing Rubber Seal is designed from the original part for superior fitment and seal. This seal mounts at the rear of the engine bay directly to the body to seal between the firewall and hood.
Cowl Vent Gasket
p/n: 20-1613-54
This Cowl Vent Gasket is designed from the original part for superior fitment and seal. Manufactured to OEM specifications to install for an authentic fit and finish.
Door Check Link Rod End Stop
p/n: 20-1640-70
This Door Check Link Rod End Stop is designed from the original part for superior fit and function. This door stop fits between the door and body to limit the swing opening of the door preventing overtravel. Door check arm and bumper. Enough for one door.
Door Jamb Bumper
p/n: 20-2366-71
This Door Jamb Bumper is a quality reproduction of the original factory part. This rubber bumper mounts into a slot in the door jamb to cushion the door closure. Two (2) required per door.
Door weatherstrip
p/n: 20-1644-73
Weatherstrips, open car door hinge. Door seals molded to fit hinge area.
Door Weatherstrip - Lower
p/n: 20-1651-73
This Lower Door Weatherstrip is designed from the original part for superior fitment and seal. This weatherstrip mounts in the lower door seal retainer. One (1) piece cuts to do two (2) doors.
Door Weatherstrip Kit
p/n: 20-1655-72
Door edge weatherstrip. This set is the primary door to body perimeter weatherstrip.
Engine Mount
p/n: 20-1978-11
This Engine Mount is designed from the original part for superior fitment and function. This engine mount works to absorb and isolate engine and driveline vibrations. The set services one mount. 1937-1941 require four (4) sets for both Front and Rear. 1942-1948 require two (2) sets.
Fender Skirt Edge Weatherstrip
p/n: 20-0111-44
This Fender Skirt Edge Weatherstrip pair is designed from the original part for superior fitment, finish and sealing function. Two five (5) foot strips that fit between the rear wheel fender skirt and rear quarter panel.
Fender Welting
p/n: 20-1590-44
This black Fender Welting is designed from the original part for superior fitment and seal. This welting material fits between the fenders and the vehicle body. Thirty (30) foot roll.
Fender Welting
p/n: 20-1591-44
This black Fender Welting is designed from the original part for superior fitment and seal. This welting material fits between the fenders and the vehicle body. Eight (8) foot length.
Front Axle Bumper
p/n: 20-1577-33
This Front Axle Bumper is a quality reproduction of the original factory part. These bottoming bump stops are dense rubber blocks that mount with a stud to a front axle bracket.