This front door vent window weatherstrip kit is a six (6) piece set that contains the main vent window seals, base extensions, and division post seals. All of the pieces were designed from original parts for a precise, factory fit.
This front door vent window weatherstrip set contains the main seals for the vent windows and the base extension pieces for the frame. They are designed and molded from original parts for superior fitment and seal.
Door edge weatherstrip. This part is the primary door to body weatherstrip.
This windshield gasket mounts around the full perimeter of the front glass and has the divider bar molded directly into it for a precise, factory fit. It also has the slot to accommodate the outer edge's decorative molding.
This windshield gasket mounts around the full perimeter of the front glass and has the divider bar molded directly into it for a precise, factory fit.
Convertible roof rail weatherstrip. This part fits on the folding roof of the vehicle and seals the side window when the window is fully raised.
Convertible Hinge Pillar Weatherstrip - Attaches to the body and seals between the A-pillar post and the front section of the door or vent window frame when the door is closed.
Seal, header bow. Installs on top of windshield.
Pad, fenderskirt edge, similar to our #70-0055-45, but thinner. Approximately five (5) foot strip per skirt.Length: 60.0 inches. Width: .15625 inches.
Side window vertical leading edge weatherstrip.
Grommet, fuel filler neck. Bonded to metal.
Sash channel, front door. Left side.
Sash channel, front door. Right side.
Seal, front of vent window foot. Included with vent window seal kit numbers 0A-7621448-PR and 8A-7621448-PR.
Window felt inner and/or outer. Flexible, pile lined, rubber covered, with black bead. Available in 3ft pair.
Weatherstrip, door window inner and outer, front and rear doors. Bend to fit. Available in a 3ft pair.
Window felt inner and/or outer. Flexible, pile lined, rubber covered, with black bead. Available in 3ft pairs.
This trunk weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the trunk lid.
This Front Vent Window Division Bar Weatherstrip pair is designed from the original part for superior fitment and seal. Parts are fully molded with a metal core and attached with rivets on the backside.
Pad, accelerator pedal cover. (Accessory).
Seal pad, rubber tape. Fifteen (15) foot roll.
Shim, windshield post between post and seals.
Front Engine Mount - Two (2) required per car. Ford only 6 or 8 cylinder engines.
Grommet, emergency brake cable firewall.
Mount, rear motor.
Seals, air vent damper. Must drill out spot welds to replace the cracked rubber. Includes screws to put back together.
Seal, rear stone deflector to bumper.
Channel, quarter window glass to stainless frame rubber.
Pads, fuel tank to body.
Seal, radiator air deflector to hood.
Pads, brake and clutch pedal.
Pads, parking light assembly to fender.
This trunk weatherstrip is designed from the original part for superior fitment and seal. The seal mounts to the lip on the body surrounding the trunk opening.
Pads, back-up light to body.
Insulator, transmission gear shift column lever.
Seal, steering column tube. Installs on top of floor mat.
Seal, door glass and window frame. Retains glass in frame. Enough for one window only.
Bumper, rear lamp bracket. Type w/Tire Carrier.
Hose, fuel tank to filler neck.
Repair kit, gear shift lever grommet. Column shift only. Two (2) kits required.
Seal, air vent assembly to firewall.
Bumper, front suspension lower arm. Bumper section is 2" tall and 1-15/16" wide.
Pads, taillight housing to body.
Seals, tie rod end. Four (4) piece set.
Pad, trunk lid handle base and left side handle to trunk lid. Two (2) piece set.
Seal, brake or clutch pedal arm.
Seal, front splash apron to radiator lower rubber.
Bolt and bushing, front of rear spring. Two (2) kits required per car.
Seal, standard trans. steering post to floor. Installs under metal plate.