This windshield gasket set includes two (2) gaskets that are made to be overlapped at the center to form the divider bar. They lock together tightly for a great seal and authentic look. It also has the slot to accommodate the outer edge's decorative molding.
Door edge weatherstrip. This part is the primary door to body weatherstrip.
This liftgate weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter directly to the liftgate.
This rear window gasket set mounts around the two (2) separate back windows. They have vulcanized, or bonded, ends which means no cutting or splicing is required for installation.
Seal, special window-sweep. Station Wagons only: Rubber that goes between door glass and staples to wooden frame. Use on door and quarter windows.
Pad, fenderskirt edge, similar to our #70-0055-45, but thinner. Approximately five (5) foot strip per skirt.Length: 60.0 inches. Width: .15625 inches.
Channel, side window glass, vertical run. Flexible, felt lined, rubber covered channel. Available 60" lengths.
Channel, flexible door window run. Stainless steel beaded. Available in 5ft lengths.
Window felt inner and/or outer. Flexible, pile lined, rubber covered, with black bead. Available in 3ft pair.
Weatherstrip, door window inner and outer, front and rear doors. Bend to fit. Available in a 3ft pair.
Fuel Filler Neck grommet.
These tailgate weatherstrips are designed from the original parts for superior fitment and seal. These seals mount on the side of the tailgate.
Window felt inner and/or outer. Flexible, pile lined, rubber covered, with black bead. Available in 3ft pairs.
Pad, accelerator pedal cover. (Accessory).
Seal pad, rubber tape. Fifteen (15) foot roll.
Shim, windshield post between post and seals.
Front Engine Mount - Two (2) required per car. Ford only 6 or 8 cylinder engines.
Grommet, emergency brake cable firewall.
Mount, rear motor.
Seals, air vent damper. Must drill out spot welds to replace the cracked rubber. Includes screws to put back together.
Seal, rear stone deflector to bumper.
Pads, fuel tank to body.
Seal, radiator air deflector to hood.
Pads, brake and clutch pedal.
Pads, parking light assembly to fender.
This tailgate weatherstrip is designed from the original part for superior fitment and seal. The seal mounts on the bottom of the tailgate.
Pads, back-up light to body.
Insulator, transmission gear shift column lever.
Seal, steering column tube. Installs on top of floor mat.
Bumpers, tailgate arms to tailgate.
Bumper, rear lamp bracket. Type w/Tire Carrier.
Hose, fuel tank to filler neck.
Repair kit, gear shift lever grommet. Column shift only. Two (2) kits required.
Seal, air vent assembly to firewall.
Bumper, front suspension lower arm. Bumper section is 2" tall and 1-15/16" wide.
Pads, taillight housing to body.
Seals, tie rod end. Four (4) piece set.
Seal, brake or clutch pedal arm.
Seal, front splash apron to radiator lower rubber.
Bolt and bushing, front of rear spring. Two (2) kits required per car.
Seal, standard trans. steering post to floor. Installs under metal plate.
Pads, trunk hinges to body. Four (4) piece set.
Grommet, transmission inspection. One (1) required per car.
Seals, back-up light lens to housing.
Gaskets, wiper pivot spacer to body. Replaces factory #8A-17541-B.
Pad, radiator support to frame.
Seal, clutch arm plate to floor. Installs under metal plate.
Seal, fuel tank filler pipe to trunk floor.
Seals, taillight lens to housing.