Weatherstrip, front door kit. Includes sufficient weatherstrip for door perimeter and hinge pillar. Eight (8) piece kit.
Weatherstrip, rear quarter vent window.
This front door vent window weatherstrip set is a four (4) piece set that contains the main vent window seals and division post seals. All of the pieces were designed from original parts for a precise, factory fit.
Rear door vent window rubber. Order our #30-0347-74 division post seal separately.
Weatherstrip, front door to fender (hinge pillar). Soft, solid rubber construction with tabs for all screws, but without metal core.
This Windshield Gasket mounts around the full perimeter of the front glass and has the divider bar molded directly into it for a precise, factory fit.
These front door vent window weatherstrips are the main seals needed to replace the rubber on your vent windows. They are designed and molded from original parts for superior fitment and seal.
This Rear Window Gasket is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the back glass and has vulcanized, or bonded, ends which means no cutting or splicing is required for installation.
This Revulcanization Service Only is designed to restore your Engine Support Mount to a like new original condition. Service requires your metal core. Please call or email for more service details and ordering.
This Electromatic Clutch Control or Brake Vacuum Cylinder Diaphragm is designed from the original part for superior fitment and function. Used in different locations dependent upon vehicle make.
Pads, taillight mounting. For ribbed door lights. Fully molded rubber for both right and left.
Bumpers, rear axle spring.Length: 5.375 inches. Width: 2.75 inches. Height: 2.1875 inches.
Insulator assembly, transmission support. Revulcanization service only. Send in your old core for service.
Bumper, front spring rebound, lower.Width: 2.125 inches. Height: 2.25 inches.
This Peel-N-Stick Trunk Weatherstrip is designed for superior fitment and seal. The seal mounts around the full perimeter of the trunk directly to the body. Easy to install 3M Peel-N-Stick backing provides superior adhesion for reliable performance.
Pedal, accelerator. Revulcanization service only. Includes new rod ball socket and pivot. Original pattern tread.Length: 9.625 inches. Width: 1.9375 inches.
Grommets, rear bumper extension bar through rear fender for wrap around bumpers. Fully molded rubber w/ full detail as in original. Four and one half inch (4-1/4") outside diameter by one and five eighths inch (1-5/8") inside hole length by one fourth inc
Hose, hydraulic window lift. Eighteen (18) inches long.
This Trunk Weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the trunk directly to the body.
Grommet, rear door vent divider post. Upper and lower, right and left. 4 piece set.
Grommet, radiator cradle to frame tie rod. 1st type, with locating boss. One four (4) piece set required per car. See also our #30-0309-31.
This Engine Mount Pad pair is used as a support cushion at the timing gear cover. Correct design and rubber compound. Sold only in pairs. One (1) pair required per car.
Welting, fender, bright chrome vinyl, three sixteenths (3/16) inch bead, one and one half (1-1/2) inch width. Superior quality. Fifty (50) foot roll. Typically used to attach four (4) fenders to body. For twenty five (25) foot roll see #70-1101-44.
Cushion, rear gravel to bumper. Six (6) feet long. One (1) strip required per car.Length: 72.00 inches. Width: .25 inches. Height: .6875 inches.
This Engine Mount Pad pair is used as a support insulator at the timing gear cover. Correct design and rubber compound.
Bumper, front spring rebound, upper.Height: 2.25 inches.
Pads, brake and clutch pedal, slip over type. Black and red rubber. For black only see our #30-0188-22.Length: 3.875 inches. Width: 2.875 inches.
Pads, brake and clutch pedal, slip over type. Black and red rubber. For black only see our #30-0114-22.
Channel, rigid run, for division bar, un-beaded, plush lined, cloth covered, twenty four (24) inches long, channel size one half (1/2) inch outside width
Retainer, intermediate bearing. All models with two piece driveshafts.
Pads, brake and clutch pedal, slip over type. Black rubber only. For black and red (semi-automatic clutch models) see our #30-0188-89.Length: 3.875 inches.
Grommets, hood lock link through firewall.
Pads, brake and clutch pedal, slip over type. Black rubber only. For black and red (electromatic clutch models) see our #30-0114-89.
Grommet, several useages. Radiator core cradle tie rod to frame or rear stablizer pad to link to where the leaf springs are bolted. Fully molded rubber. 2nd type with chamfered edge. Comes as a (4) piece set. One and three eighths inch (1 3/8") outside di
Bushings, front stabilizer mounting bracket. Fully molded rubber. One and seven sixteenths inch (1 7/16") length by one and five eighths inch (1 5/8") width by five eighths inch (5/8") inside hole diameter by one and eleven sixteenths inch (1 11/16") heig
Grommet, ignition cable.Length: 2.125 inches. Width: 1.50 inches.
Channel, flexible window run, un-beaded. Cloth covered mohair-lined type. Available in 6ft lengths.
This four (4) piece Engine Snubber Pad Set is designed from original for correct fit and function. Sold only in complete sets. One four (4) piece set required per car.
Front vent window division post seal. Fully molded with metal core and attaching tabs.
Weatherstrip, rear vent window, front edge (on division post) right and left.
Cloth covered, mohair lined flexible metal channel for sides and top of door windows.
These Window Felt Beltline Weatherstrips are sold as a three (3) foot pair. The beltline is used for side windows inner and/or outer, front and/or rear doors. Available in a 3ft pair.
Boot, brake and clutch pedal shank at toe board.Length: 2.9375 inches.
Grommet, shifter shaft to shroud. One (1) per car.Length: 4.125 inches. Width: 2.3125 inches.
Pad, rear license light mounting, with correct dimensions and beading.Length: 8.125 inches.
Welting, fender, bright chrome vinyl, three sixteenths (3/16) inch bead, one and one half (1-1/2) inch width. Superior quality. Twenty five (25) foot roll. Typically used to attach two (2) fenders to body. For fifty (50) foot roll see our #70-1102-44.
This side window Window Felt Beltline Weatherstrip pair can be used as inner and/or outer. The weatherstrip is flexible, pile lined, rubber covered, with black bead. Available in 3ft pairs.
This Decklid Lock / Handle Mount Gasket is designed from the original part for superior fitment, finish and function. Length: 4 inches.
Gaskets, headlight body mounting to fender. Cut to exact size as original.
Cloth covered mohair-lined type. For sides and top of side windows. Available in 5ft lengths.