3/4" Trunk Weatherstrip
p/n: 30-0356-85
This Trunk Weatherstrip is made from high quality EPDM sponge rubber. Excellent for use on many different vehicle models. Available by the foot.
5/8" Channel filler weatherstrip
p/n: 30-0507-57
Seal, door window frame, upper and rear. Used on some open models with metal frame around glass. Available by the foot.
7/8" Windshield Weatherstrip
p/n: 70-1190-52
This Windshield Weatherstrip is for windows without chrome reveal molding. For a 2 piece windshield, select gasket for division bar. Available by the foot.
9/16" Channel filler weatherstrip
p/n: 70-0489-58
Weatherstrip, channel filler, door window sash channel and some quarter window sash channel. Special type with wide weatherstrip edge to be trimmed at assembly, when necessary. Available by the foot.
9/16" Window Gasket Weatherstrip
p/n: 60-0059-83
This Window Gasket Weatherstrip was designed from an original part for a specific application but has many uses outside of its original purpose. The seal is structured to be used with 1/4" glass in a 3/8" channel.
Control arm bushing seal
p/n: 60-0094-32
Seal, upper and lower control arm cross shaft bushing, at inner end of arm.1939-48: Lower only, all pass. (exc.
Door Garnish Molding Pad
p/n: 30-0435-71
Support, door garnish molding. Up to twenty (20) required per car.Width: .875 inches. Height: 1.0 inches.
Glovebox or Fuel Tank Filler Door Bumpers
p/n: 20-1220-88
This Glovebox or Fuel Tank Filler Door Bumper pair is a quality reproduction of the original factory part. This push on rubber bumper attaches to support / cushion the glovebox or filler door closure.
Rear Quarter Window Bumper
p/n: 50-0399-62
Bumper, rear quarter window stop (lower) on window guide. Both upper and lower on some models. Three fourths (3/4) inch high. Compare to our #50-0400-62.
Stabilizer Link or Shock Grommet
p/n: 70-0737-33
This Stabilizer Link or Shock Grommet is designed from the original part for superior fitment and usage. Fully molded rubber.
1/2" Door Weatherstrip
p/n: 70-0311-73
This Door Weatherstrip is designed to be an exact match to the original. The weatherstrip is made from a high-quality EPDM sponge rubber. Available by the foot.
15/16" Battery Strap Grommet
p/n: 32-0491-21
This Battery Strap Grommet is fully molded and designed from the original part for superior fitment and seal. This grommet is made from high-quality EPDM dense rubber. Designed for the battery retaining hold-down bolt.
5/8" Door Weatherstrip
p/n: 70-0219-73
The Door Weatherstrip is designed for 1941-1957 GM and Mopar vehicles but with its generic shape it has many uses outside of its original purpose. Available by the foot.
Hood to Cowl Bumper
p/n: 70-1248-42
Bumper, hood to cowl, intermediate. Attaches to our hood to cowl weatherstrips, .34 inch high. Use as required four (4) to six (6) per car.
Shock Absorber Grommet
p/n: 60-0235-33
This Shock Absorber Grommet is fully molded and designed from the original part for superior fitment and durability. The grommet the plain cylinder type with flat ends for shock absorber mounting.
1-3/16" Utility Plug
p/n: 35-0099-20
This Utility Plug is fully molded and designed from the original part for superior fitment and seal. This plug is made from high-quality EPDM dense rubber to provide excellent durability.
Hood to Cowl Bumper
p/n: 70-1247-42
Bumper, hood to cowl, intermediate. Attaches to our hood to cowl weatherstrips, .28 inch high. Use as required four (4) to six (6) per car.
Speedometer Cable Grommet
p/n: 20-2435-20
This Speedometer Cable Grommet is used to protect the cable when running it through the firewall. Designed from the original part for superior fit and seal.
Wiper control grommet
p/n: 20-2525-53
Gaskets, wiper pivot spacer to body. Replaces factory #8A-17541-A.
Wiper Hose Grommet
p/n: 20-2524-53
This Wiper Hose Grommet is used to protect the wire when running it through the firewall. Designed from the original part for superior fit and seal.
1" Floor Pan Grommet
p/n: 35-0515-20
This Floor Pan Grommet is fully molded and designed from the original part for superior fitment and seal. This grommet is made from high-quality EPDM dense rubber to provide excellent durability.
1/16" Sash Channel Filler - Cork
p/n: 70-1115-57
This 1/16" Sash Channel Filler offers the best quality cork product for your classic vehicle project. Manufactured to OEM specifications to install for an authentic fit and finish. Available by the foot.
1-5/16" Quarter Window Lift Grommet
p/n: 32-0098-21
This Quarter Window Lift Grommet is fully molded and designed from the original part for superior fitment and seal. This grommet is made from high-quality EPDM dense rubber to provide excellent durability.
Air Vent Cable Grommet
p/n: 20-2437-20
This Air Vent Cable Grommet is used where the air cable passes through the firewall. One pair required per vehicle. This grommet is also commonly used for the hood pull cable, heater wire, and electric wiper motor cable.
Body Hole Plug
p/n: 20-1041-21
Plug, cowl and floor pan. This body plug covers a sheet metal hole that is one and one seven eighths (1-7/8) inch in diameter.
Hood to Cowl Bumper
p/n: 70-1249-42
Bumper, hood to cowl, intermediate. Attaches to our hood to cowl weatherstrips. Use as required, four (4) to six (6) per car.
Tie rod dust cover
p/n: 10-0134-32
Rubber seal, tie rod ends and drag link ends. 2 or 4 required per car. Note: for 4 cylinder vehicles.
1-1/4" Headlight Cable Grommet
p/n: 32-0492-14
This Headlight Cable Grommet is fully molded and designed from the original part for superior fitment and seal. Designed for firewall applications such as running the headlight cable through the fender.
1-3/16" Firewall Grommet
p/n: 32-0112-20
This Firewall Grommet is fully molded and designed from the original part for superior fitment and seal. Designed for firewall applications such as the handbrake cable, heater control cable, and others.
1-5/16" Wiring Grommet
p/n: 32-0439-20
This Wiring Grommet is fully molded and designed from the original part for superior fitment and seal. This grommet is made from high-quality EPDM dense rubber to provide excellent durability.
3/4" Hood Side to Fender Bumper
p/n: 33-0542-42
A quality Hood Side To Fender Bumper. Button type and self-retaining. Replaces factory #391463.
Engine Mount Washer
p/n: 20-0442-11
This Front Upper Engine Mount Washer is made of steel. The large upper engine mount insulator sits in this special washer. Fits all Ford 6 cylinder and Flathead V-8 models.
Firewall Retainer
p/n: 60-0586-20
This Firewall Retainer is used on the firewall insulation panel. Designed from original for the "Christmas Tree" style popular during this time.
Front suspension bushing
p/n: 20-2470-32
Seal, front suspension. Inner lower arm.Qty Required:4 Four (4) required per car.
Gravel Shield Bumper
p/n: 33-0286-30
Bumper, rear gravel shield, anti-rattle. Five (5) or more used per car. Fully molded rubber. Replaces factory #1320392.
Hood To Radiator Weatherstrip
p/n: 20-2468-31
This Hood To Radiator Weatherstrip is designed from the original part for superior fitment and seal. An exact reproduction of the original profile. This seal functions as a radiator air deflector by mounting to the top of the radiator.
Power Top Cylinder Spacer
p/n: 70-0822-67
This Power Top Cylinder Spacer is used as the folding top power cylinder support. Molded from 100% EPDM dense rubber for durability. Four (4) spacers used per car.
Run Channel Retaining Clip
p/n: 60-0374-58
This Run Channel Retaining Clip is designed from the original part for an authentic fit, finish and function. Clip fits at the end of door window run channel. Tempered spring steel.
1-1/16" Wiring Grommet
p/n: 32-0002-21
This Wiring Grommet is fully molded and designed from the original part for superior fitment and seal. This grommet is made from high-quality EPDM dense rubber to provide excellent durability.
Body Mounting Pad
p/n: 20-0458-48
Bushings, rear of cab to frame suspension arm. Set of four (4) pieces.
Door Jamb Bumper
p/n: 20-2109-71
This Door Jamb Bumper is a quality reproduction of the original factory part. This rubber bumper mounts into a slot in the door jamb to cushion the door closure. Two (2) required per door.
Shock Absorber or Track Bar Bushing
p/n: 20-2476-33
This Shock Absorber or Track Bar Bushing is designed from the original part for superior fitment and function. These bushes are used on tubular-style shock absorbers and also on stabilizer track bar(s).