Convertible roof rail weatherstrip. This part fits on the folding roof of the vehicle and seals the side window when the window is fully raised.
This front door vent window weatherstrip kit is a six (6) piece set that contains the main vent window seals, base extensions, and division post seals. All of the pieces were designed from original parts for a precise, factory fit.
This front door vent window weatherstrip set contains the main seals for the vent windows and the base extension pieces for the frame. They are designed and molded from original parts for superior fitment and seal.
This windshield gasket mounts around the full perimeter of the front glass and has the divider bar molded directly into it for a precise, factory fit. It also has the slot to accommodate the outer edge's decorative molding.
This windshield gasket mounts around the full perimeter of the front glass and has the divider bar molded directly into it for a precise, factory fit.
Seal, header bow. Fastens to front header bow.
Seal, header bow. Installs on top of windshield.
Pad, fenderskirt edge, similar to our #70-0055-45, but thinner. Approximately five (5) foot strip per skirt.Length: 60.0 inches. Width: .15625 inches.
Seal, windshield post to door. Installs on windshield post.
Side window vertical leading edge weatherstrip.
Sash channel, front door. Right side.
Sash channel, front door. Left side.
Seal, front of vent window foot. Included with vent window seal kit numbers 0A-7621448-PR and 8A-7621448-PR.
Window felt inner and/or outer. Flexible, pile lined, rubber covered, with black bead. Available in 3ft pair.
Weatherstrip, door window inner and outer, front and rear doors. Bend to fit. Available in a 3ft pair.
Seal, lower back of quarter window to top of quarter panel.
Window felt inner and/or outer. Flexible, pile lined, rubber covered, with black bead. Available in 3ft pairs.
This trunk weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the trunk lid.
This Front Vent Window Division Bar Weatherstrip pair is designed from the original part for superior fitment and seal. Parts are fully molded with a metal core and attached with rivets on the backside.
Pad, accelerator pedal cover. (Accessory).
Seal pad, rubber tape. Fifteen (15) foot roll.
Shim, windshield post between post and seals.
Front Engine Mount - Two (2) required per car. Ford only 6 or 8 cylinder engines.
Seals, air vent damper. Must drill out spot welds to replace the cracked rubber. Includes screws to put back together.
Support, transmission. Models with manual transmission only.
Door lock pillar seal. This part seals the bottom of the rear side window, and may also be known as a door jamb seal.
Pads, fuel tank to body.
Seal, radiator air deflector to hood.
Pad, trunk lid handle base to trunk lid.
Pads, brake and clutch pedal.
This trunk weatherstrip is designed from the original part for superior fitment and seal. The seal mounts to the lip on the body surrounding the trunk opening.
Seal, rear stone deflector to bumper.
Pads, back-up light to body.
Grommet, fuel filler neck.
Insulator, transmission gear shift column lever.
Seal, steering column tube. Installs on top of floor mat.
Bumper, rear lamp bracket. Type w/Tire Carrier.
Hose, fuel tank to filler neck.
Repair kit, gear shift lever grommet. Column shift only. Two (2) kits required.
Grommets, transmission inspection. Four (4) required per car.
Seal, air vent assembly to firewall.
Pads, outside door handle. Enough for two (2) handles. Four (4) piece set.
Gaskets, taillight housing to body.
Bumper, front suspension lower arm. Bumper section is 2" tall and 1-15/16" wide.
Seals, tie rod end. Four (4) piece set.
Seal, air ventilator rear duct spring rubber.
Seal, brake or clutch pedal arm.
Seal, front splash apron to radiator lower rubber.
Bolt and bushing, front of rear spring. Two (2) kits required per car.