Search Results
Please click on the part name in red in order to get a complete description.
Front Door weatherstrip kit
p/n: 90-0116-72
Front door edge weatherstrip kit. This part is the primary door to body weatherstrip. This includes one pair of #70-0857-73 which seals the lock side of the door to the body, #70-0530-73 which seals the vent window to the pillar, #50-0219-73 front door op
Convertible Roof Rail Kit
p/n: 70-0498-65
This eight (8) piece Convertible Roof Rail Weatherstrip is designed from the original part for superior fitment and seal. This part fits on the folding roof of the vehicle and seals the side windows when the window is fully raised.
Windshield Gasket
p/n: 70-0526-50
This windshield gasket mounts around the full perimeter of the front glass and has properly molded corners for a precise, factory fit. It also has molded sections for the wiper transmissions and the slot to accommodate the outer edge's decorative molding.
Front Door Vent Window Kit
p/n: 90-0395-90
This front door vent window weatherstrip kit is a six (6) piece set that contains the main vent window seals, base extensions, and division post seals. All of the pieces were designed from original parts for a precise, factory fit.
Front Door Vent Window Weatherstrips
p/n: 38-0051-55
This front door vent window weatherstrip set contains the main seals for the vent windows and the base extension pieces for the frame. They are designed and molded from original parts for superior fitment and seal.
Door weatherstrip
p/n: 70-0857-73
Weatherstrip, front door lock pillar. Ready to install with molded ends.Length: 36.0 inches. Width: .625 inches. Height: .625 inches.
Door weatherstrip
p/n: 70-0550-73
Weatherstrip, door bottom (1951-2nd type). Molded left and right, overall length forty (40) inches.
Door weatherstrip
p/n: 70-0530-73
Weatherstrip, front door. Upper on edge of door or body opening. Molded ends, right and left.
Hood to cowl weatherstrip
p/n: 50-0436-43
Weatherstrip, hood to cowl. 31" long. Note: compare to #50-0167-43 hood to cowl sold separately.
Axle rebound pad
p/n: 50-0371-35
Bumper, rear axle. Revulcanization service only.Height: 3.5 inches.
Hood to cowl weatherstrip
p/n: 50-0167-43
Weatherstrip, hood to cowl. 56 1/2 " long. Note: compare to #50-0436-43 hood to cowl sold separately.
Motor mount service
p/n: 50-0297-11
Motor mount, front. Revulcanization service only.Qty Required:2 Length: 3.375 inches. Width: 2.625 inches. Height: 1.25 inches.
Front bow weatherstrip
p/n: 50-0401-64
Weatherstrip, front bow. With metal core in center section as original.Length: 52.0 inches. Width: .8125 inches. Height: .375 inches.
Trunk Weatherstrip
p/n: 70-0871-84
This trunk weatherstrip set is designed from original parts for superior fitment and seal. The set contains the strips and corners that mount to the body and the strip that mounts to the lid.
Transmission mount service
p/n: 50-0264-25
Support pad, transmission mount (insulator). Revulcanization service only.Length: 5.0 inches. Width: 2.0 inches.
Transmission mount service
p/n: 50-0263-25
Support, transmission (insulator). Revulcanization service only. See also our #50-0262-25, many models use both.Length: 5.0 inches. Width: 1.875 inches.
Transmission mount service
p/n: 50-0262-25
Pad, transmission mounting, thrust. Revulcanization service only. One (1) per car required. See also our #50-0263-25. Many models use both.Length: 7.
Torque ball service
p/n: 50-0190-27
Retainer, torque ball, heavy steel jacket with molded rubber inner collar. Revulcanization service only.
Door weatherstrip hinge pillar
p/n: 50-0268-73
Weatherstrip, body hinge pillar to door, bellows type seal.
Rigid run channel
p/n: 70-0536-58
Run channel, front door window, for full length of division bar (approximately twenty nine (29) inches). Rigid, bright beaded edge, mohair lined channel, die trimmed and formed at top.
Convertible post bumper
p/n: 50-0208-67
Bumper, on folding top female hinge, for folding post, when top is retracted, right and left, brass core as original.Length: 1.8125 inches. Width: 1.
Fender welting 50ft chrome
p/n: 70-1102-44
Welting, fender, bright chrome vinyl, three sixteenths (3/16) inch bead, one and one half (1-1/2) inch width. Superior quality. Fifty (50) foot roll. Typically used to attach four (4) fenders to body. For twenty five (25) foot roll see #70-1101-44.
Trunk Weatherstrip Corners
p/n: 60-0511-85
These trunk weatherstrip corners are designed from the original part for superior fitment and seal. The seals mount to the front corners of the trunk directly to the body.
Door bumper
p/n: 70-0168-71
Bumper, door side. Square type held by four (4) screws, metal core as original.
Front Stablizer Bar End Link Kit
p/n: 70-0567-34
Kit, stabilizer bar link assembly. Twenty two (22) piece set for both sides of one (1) car, front and rear. (Order 2 sets if you need both). Hex head bolt. 5/16"-24nf x 7-5/8" lg. Comes with metal sleeve, cup washers and rubber grommets.
Clutch equalizer bushing kit
p/n: 70-2029-24
Kit, clutch equalizer bushing & seal. Kit includes metal sleeved rubber bushing and molded rubber seals for each end of equalizer.
Rear coil spring pad
p/n: 50-0359-35
Insulators, rear coil spring. Fabric reinforced rubber as original. One (1) pair per car.
Run Channel Upper Bumper
p/n: 60-0183-62
Bumper, side window glass in vent frame at top, right and left, brass core.Length: 1.625 inches.
Rigid Run Channel
p/n: 70-0347-58
Channel, rigid run, window division bar. Stainless beaded edge, mohair-lined, exact replacement for rear side of division bar.
Beltline weatherstrip
p/n: 70-0555-58
Weatherstrip, door window inner and outer, front and rear doors. Seven sixteenths (7/16) inch wide, with chrome bead, mohair faced, flexible. Two (2) three (3) foot strips. Bend to fit.
Headlight Door To Lens Seal
p/n: 70-0389-14
Headlight door to lens seal. Molded without wire. Single lip type for sealed beams.
Vent division bar weatherstrip
p/n: 70-0821-56
Front vent window division post seal. Fully molded with metal core and attaching tabs.
Front stabilizer bushing
p/n: 50-0094-34
Bushings, front stabilizer shaft-to-frame or stabilizer shaft, front or rear. Fully molded rubber. One and one half inch (1 1/2") length by one and one half inch (1 1/2") width by eleven sixteenths inch (11/16") inside hole diameter by one and one half in
Brown brake and clutch pad
p/n: 50-0054-89
Pad, brake and clutch pedal. Brown rubber. For black see our part #50-0054-22. Perfect copy, fine detail.Color:brown Width: 3.125 inches.
Fender welting 25ft chrome
p/n: 70-1101-44
Welting, fender, bright chrome vinyl, three sixteenths (3/16) inch bead, one and one half (1-1/2) inch width. Superior quality. Twenty five (25) foot roll. Typically used to attach two (2) fenders to body. For fifty (50) foot roll see our #70-1102-44.
Sliding Quarter Window Weatherstrip
p/n: 70-0353-78
Weatherstrip, inner and outer for sliding quarter window, chrome beaded, mohair faced, flexible stock. May be formed to required outline. Six (6) foot strip.
Door weatherstrip
p/n: 50-0219-73
Weatherstrip, front door opening, front body hinge pillar, lower. Extruded sponge to original configuration. Two (2) required per car.Width: .875 inches.
Front suspension bumper
p/n: 50-0092-32
Bumper, front suspension, lower arm. Steel core, with threaded stud, as original. Two (2) per car required.
Steel sash channel
p/n: 70-0641-58
Sash channel, side window glass. U-shaped steel channel only, no filler. Will require that you attach your own window regulator cam to underside as required.
Convertible top rest block
p/n: 70-0397-67
Pad, convertible top assembly. Rubber only, cements to original metal core.
Rigid run channel
p/n: 70-0516-58
Channel, rigid run, lower side window below beltline, zinc plated steel with black cloth lining, one half (1/2) inch deep by one half (1/2) inch wide, fifteen (15) inches long.
Convertible top arm pad
p/n: 50-0402-67
Rest pad, convertible top. Two (2) per car.Length: 1.6875 inches. Width: 1.125 inches.
Bowdrill cloth tape
p/n: 70-1175-65
Tape, black bowdrill cloth. Adhesive backed, used to create cloth cover surface for side rail weatherstrips typically. Five (5) inches by five (5) foot roll. Pressure sensitive, for covering convertible side window weatherstrip such as our #70-1170-99 or
Brake and clutch shank seal
p/n: 50-0066-24
Grommet, brake and clutch pedal floor seal.Width: 1.8125 inches. Height: 2.375 inches.
Brake and clutch pedal pad
p/n: 50-0054-22
Pad, brake and clutch pedal. Black rubber. For brown see our part #50-0054-89. Perfect copy, fine detail.Width: 3.125 inches. Height: 2.125 inches.
Front coil spring pad
p/n: 50-0358-35
Insulators, front coil spring. Fabric reinforced rubber as original.
Front bow weatherstrip
p/n: 70-0785-64
Weatherstrip, front bow of convertible. Sponge rubber extrusion of correct dimensions.Length: 60.0 inches. Width: .8125 inches.
Quarter Window Leading Edge Weatherstrip
p/n: 70-0141-58
This Leading Edge Vertical Weatherstrip seal pair is designed from the original part for superior fitment and seal. Slides into metal retaining channel attached to rear side window and seals between the front door window and the rear quarter window.
Heater control valve seal
p/n: 50-0356-20
Seal, heater control valve. High quality sponge rubber designed to cushion heater control valve and keep out noise and water. For all except right-hand drive.
Trunk bumper
p/n: 70-0296-87
T-nut, trunk bumper in gutter at sides, brass core tapped 10-32 thread. Two (2) required per car. For models having partial weatherstrip in gutter of body.
Body mounting pad
p/n: 50-0477-48
Pad, body mounting. Fully molded rubber with metal core & locating collar. One and seven eighths inch (1 7/8") outside diameter by one and one eighths inch (1 1/8") locating collar outside diameter by three fourths inch (3/4") locating collar inside diame
Taillight mounting pad
p/n: 50-0410-15
Pad, taillight to fender.Width: 7.25 inches. Height: 4.0 inches.
Door handle gasket kit
p/n: 50-0322-69
Gasket set, door handle, outside. For front and rear door if necessary. Six (6) piece set for two (2) doors.
Taillight lens gasket
p/n: 50-0411-15
Gasket, taillight lens. Die cut three sixteenths (3/16) inch sponge rubber as original.Width: 6.25 inches. Height: 3.25 inches.
Hydraulic pump mounting pad
p/n: 70-0852-67
Pad, mounting, hydraulic pump. Used on models with hydraulic window lifts or hydraulic convertible top. Two (2) to three (3) required. per car.
Battery clamp cover
p/n: 70-0095-21
Cover, battery clamp. Control unsightly sulfate buildup. Help protect the nearby metal and finish. Good copy from original part.Length: 3.5 inches.
Bowdrill cloth tape
p/n: 70-1172-65
Tape, black bowdrill cloth. Adhesive backed, used to create cloth cover surface for side rail weatherstrips typically. Two and one half (2-1/2) inches by five (5) foot roll. Pressure sensitive, for covering convertible side window weatherstrip such as our
Hood bumper
p/n: 50-0159-42
Bumper, hood ledge corner at shroud.Width: 1.25 inches. Height: .5 inches.
Body mounting pad
p/n: 50-0478-48
Pad, body mounting. Fully molded rubber with locating collar. Two (2) are needed per car. Two inches (2") outside diameter by one inch (1") locating collar outside diameter by three fourths inch (3/4") locating collar inside diameter. One half inch (1/2")
Body mounting pad
p/n: 50-0096-48
Pad, body mounting. Fully molded rubber with steel core and locating collar. Two inch (2") square by one and one eighth inch (1 1/8") locating collar outside diameter by eleven sixteenths inch (11/16") locating collar inside diameter by one half inch (1/2
Rear coil spring pad
p/n: 50-0304-35
Insulator, rear coil spring clamp bolt (upper end). Two (2) per car. Fabric reinforced rubber as original.
Tan bowdrill cloth tape
p/n: 70-1173-65
Tape, brown (tan) bowdrill cloth. Adhesive backed, used to create cloth cover surface for side rail weatherstrips typically. Two and one half (2-1/2) inches by five (5) foot roll. Pressure sensitive, for covering convertible side window weatherstrip such
Parking and signal lens gasket
p/n: 50-0381-16
Gasket, front parking and signal light lens gasket. Backup lens on cars with optional backup lenses.
Hood bumper
p/n: 50-0277-42
Bumper, hood side to fender ledge. Metal core molded in as original.Width: 1.875 inches. Height: .8125 inches.
Body Mounting Pad
p/n: 50-0361-48
Pad, body mounting. Required replacement for body-off restorations. Constructed of high quality rubber for long lasting durability. Two inch (2") square by fifteen sixteenths inch (15/16) inside hole diameter by one fourth inch (1/4") height.
Masticated rubber sheet
p/n: 70-0645-45
Masticated sheet. Three thirty seconds (3/32) inch thick rubber sheet containing random milled cotton cord reinforcement for front end splash aprons, etc. This product is a four (4) foot wide roll, and will only be sold in four (4) square foot multiples
Firewall grommet
p/n: 50-0364-20
Grommet, firewall, oil pressure and water temperature, or washer vacuum hose.
License lens gasket
p/n: 50-0357-17
Gasket set, rear license light assembly. One (1) rubber ring and one (1) cork rubber gasket comprise set.
Axle rebound pad
p/n: 50-0302-35
Bushing, rear axle, anti-sway rod ends. Fully molded rubber. Four (4) required per car. One and one fourth inch (1 1/4") top outside diameter by one and one eighth inch (1 1/8") bottom outside diameter by five eighths inch (5/8") inside hole diameter by t
Glovebox link bumper
p/n: 50-0367-88
Bumper, glove box check link. Fits on glove box door arm as needed.Length: .75 inches. Width: .5625 inches. Height: .3125 inches.
Window stop stem bumper
p/n: 33-0540-62
Cushion (stem bumper), window stop, lower. For front and rear door, rear side and quarter windows as required.
Door Weatherstrip (Sponge Rubber Extrusion - General Use)
p/n: 70-0492-73
Door edge weatherstrip made from high quality EPDM sponge rubber. Excellent for use on many different vehicle models.
Shift lever grommet
p/n: 50-0284-24
Grommet, shift lever insulator. One (1) per car. Three eighths (3/8) inch inside diameter by five eighths (5/8) inch barrel by one half (1/2) inch long.
Side window roller
p/n: 70-0117-62
Anti-rattle roller, side windows. Rubber only, replaces original perfectly and easily. Fits both styles of brackets.
Brown door lock knob
p/n: 70-0660-70
Knob or push button for inside door lock, fits over 1/8" steel rod to door lock. Hard brown rubber, may be lacquered other colors as required.
Trunk Weatherstrip (Sponge Rubber Extrusion - General Use)
p/n: 70-0463-85
Trunk weatherstrip made from high quality EPDM sponge rubber. Excellent for use on many different vehicle models.
Run channel mohair liner
p/n: 70-2863-58
Liner, mohair. Liner with a rubber backing. Apply with adhesive to division bars and channels. Helps reline guide bars on lock side of hardtops and convertibles.
Trunk Weatherstrip
p/n: 50-0161-85
This weatherstrip was designed from an original part for a specific application but has many uses outside of its original purpose. The seal is structured to be applied to the body of the car.
Door Weatherstrip
p/n: 70-0491-73
Weatherstrip, door edge. Fine grain sponge. Larger type used on most GM cars this period. Width: 13/16". Height: 11/16".
Shock and stabilizer grommet
p/n: 70-0274-33
Grommet, shock and stabilizer link. Eight (8) required per car. Fully molded rubber with locating collar. One and one sixteenth inch (1 1/16") outside diameter by nine sixteenths inch (9/16") locating collar outside diameter by three eighths inch (3/8") i
Trunk Weatherstrip (Sponge Rubber Extrusion - General Use)
p/n: 60-0411-85
Trunk weatherstrip made from high quality EPDM sponge rubber. Excellent for use on many different vehicle models.
Lock cylinder gasket
p/n: 70-0955-86
Gasket, trunk lock cylinder. Steel rule die cut from one thirty seconds (1/32) inch dense rubber.Length: 1.75 inches. Width: 1.25 inches. Height: .
Pressure ring
p/n: 70-0261-69
Pressure ring (washer), sponge rubber, interior door handle and window regulator escutcheon. One and three fourths (1-3/4) inches outside diameter by three eighths (3/8) inch thick.
Rear quarter window bumper
p/n: 50-0400-62
Bumper, rear quarter window stop (upper) on window guide. Both upper and lower on some models. Compare dimensions to our #50-0399-62.Length: .9375 inches.
Universal mounting pad
p/n: 70-0308-17
Mounting pad, continuous for lights, hinges, brackets, and other bright work when no molded pad is available.