Please click on the part name in red in order to get a complete description.
This windshield gasket set contains the windshield gasket itself and the locking strip. The seal mounts around the full perimeter of the front glass and has properly molded corners for a precise, factory fit.
Weatherstrip, front door kit. Includes weatherstrip for door perimeter and hinge pillars.
Weatherstrip, front door hinge pillar.
This front door vent window weatherstrip kit is a four (4) piece set that contains the main vent window seals and division post seals. All of the pieces were designed from original parts for a precise, factory fit.
These front door vent window weatherstrips are the main seals needed to replace the rubber on your vent windows. They are designed and molded from original parts for superior fitment and seal.
Engine support, front. Revulcanization service only.
Support, engine mount at rear. Revulcanization service only.
Bumper, front spring compression, lower arm. Steel core, retained by clip (not included).Height: 2.625 inches.
Gasket, taillight to body. Sold in pairs.Length: 11.875 inches.
Bumper, front spring rebound, lower.Width: 2.125 inches. Height: 2.25 inches.
This trunk weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the trunk directly to the body.
Pedal, accelerator. Revulcanization service only. Includes new rod ball socket and pivot. Original pattern tread.Length: 9.625 inches. Width: 1.9375 inches.
Weatherstrip, hood to cowl. Fully molded with carrot-bumper retainers.Width: .625 inches.
Grommet, steering column at floorboard.Length: 4.50 inches.
Bumper, front spring rebound, upper.Height: 2.25 inches.
Retainer, intermediate bearing. All models with two piece driveshafts.
Bumper, rear axle rebound.Length: 3.0 inches. Width: 2.375 inches. Height: 1.6875 inches.
Bearings or bushings, front stabilizer rod. One (1) pair used per vehicle. Fully molded rubber. One and nine sixteenths inch (1 9/16") length by one and nine sixteenths inch (1 9/16") width by three fourths inch (3/4") inside hole diameter by one and elev
Front vent window division post seal. Fully molded with metal core and attaching tabs.
Seal, rear shield to bumper.Length: 84.0 inches. Width: .75 inches.
Grommet, ignition cable.Length: 2.125 inches. Width: 1.50 inches.
Bushings, front stabilizer rod end. One (1) pair required per car. Fully molded rubber. One and one half inch (1 1/2") length by one and one eighth inch (1 1/8") width by three fourths inch (3/4") inside hole diameter by one and one half inch (1 1/2") hei
Weatherstrip, door window inner and outer, front and rear doors. Seven sixteenths (7/16) inch wide, with chrome bead, mohair faced, flexible. Two (2) three (3) foot strips. Bend to fit.
Gaskets, headlight body mounting to fender. Cut to exact size as original.
Headlight body mounting gasket. Rubber.
Grommet, heater core at firewall.Length: 3.5625 inches. Width: 2.25 inches.
Grommet, handbrake rod to dash.Height: 1.875 inches.
Grommet, wiring harness.
Gasket, rear bumper license plate lens. Machine die-cut from 1/16" rubber.Length: 6.5625 inches. Width: 1.625 inches.
Back-Up Light To Body Gaskets - A pair of top quality molded rubber seals manufactured to authentic original dimensions. These gaskets are designed and made for a precise, factory like fit and performance.
Boot, gearshift on steering column. Brown rubber. For black see our #30-0069-36. Two and one eighth (2-1/8) inch long style.
Gasket, taillight lens to body mount. High quality replacement of normally deteriorated part. Nine and one half (9-1/2) inches long.Length: 9.50 inches.
Pad, rear spring insulator. Order four (4) per car.Length: 4.75 inches. Width: 2.875 inches.
Boot, gearshift on steering column. Black rubber. For brown see our #30-0069-89. Two and one eighth (2-1/8) inch long style.Length: 2.25 inches.
Boot, starter solenoid.
Grommet, carpet. Floor front carpet grommet use for power brake hole.
Pad, fender mounted antenna.Length: 2.5 inches.
Pad, body mounting. Fully molded rubber with metal core and rubber locating collar. Also used for radiator cradle to frame. Eight (8) to ten (10) required per car. Two and one fourth inch (2 1/4") outside diameter by one and one sixteenth inch (1 1/16") l
Cover, battery clamp. Control unsightly sulfate buildup. Help protect the nearby metal and finish. Good copy from original part.Length: 3.5 inches.
Bumper, hood, on side of fender. Six (6) required per car.Length: 1.0 inches. Width: 1.375 inches.
Grommet, antenna mounting. Fits all models with power antenna. Used with our #70-0756-19.
Insulator, rear spring leaf clip. Seven and one half (7-1/2) inch long, customer may trim for shorter lengths. May use up to eight (8) per car.
Grommet, dimmer switch for carpet application.
Masticated sheet. Three thirty seconds (3/32) inch thick rubber sheet containing random milled cotton cord reinforcement for front end splash aprons, etc. This product is a four (4) foot wide roll, and will only be sold in four (4) square foot multiples
Knob, inside door lock control, flexible rubber, black only.Height: 1.125 inches.
Pad, body mounting. Fully molded rubber. Also used for radiator cradle to frame. Eight (8) to ten (10) required per car. Two and one eighth inch (2 1/8") outside diameter by three fourths inch (3/4") inside hole diameter by five sixteenths inch (5/16") he
Grommet, headliner bow end. Twelve (12) required per car.Length: 1.4375 inches.
Dust cover, tie rod ends.
Grommet, overdrive control linkage. Spool type grommet used on manual transmission models with factory overdrive. Three fourths inch (3/4") outside diameter by three eighths inch (3/8") inside hole diameter by three eighths inch (3/8") height.
Grommet, spark plug & coil wire at distributor cap outlets. For nine (9mm) millimeter wire, earlier years.
This trunk weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the trunk directly to the body. Easy to install 3M Peel-N-Stick backing provides superior adhesion for reliable performance.
Cushion Horn BUTTON
Weatherstrip, door edge. Fine grain sponge. Larger type used on most GM cars this period. Width: 13/16". Height: 11/16".
Trunk weatherstrip made from high quality EPDM sponge rubber. Excellent for use on many different vehicle models.
Mounting pad, continuous for lights, hinges, brackets, and other bright work when no molded pad is available.
Weatherstrip, door edge, constant section on some models. Five eighths (5/8) inch by (5/8) inch cross-section, high grade, fine grain sponge rubber.
Grommet, shock absorber mounting, plain cylinder type with flat ends.
Filler strip, window glass sash channel. One sixteenths (1/16) inch thick by 1-1/2 inches wide. For all applications fitting glass to sash channel not requiring weatherstrip type of filler. This is the highest quality linen back, rubber cork composition on
Pad, hood side to fender. Button type, fits five sixteenths (5/16) inch hole, self retaining.
Filler strip, window glass sash channel. One sixteenths (1/16) inch thick by 1-1/2 inches wide. For all applications fitting glass to sash channel not requiring weatherlip type of filler. This is the highest quality rubber like polymer designed for settin
Filler strip, window glass sash channel. One thirty seconds (1/32) inch thick by 1-1/2 inches wide. For all applications fitting glass to sash channel not requiring weatherlip type of filler. This is the highest quality linen back, rubber cork composition
Filler strip, window glass sash channel. One thirty seconds (1/32) inch thick by 1-1/2 inches wide. For all applications fitting glass to sash channel not requiring weatherlip type of filler.