Spring Shackle Bushing Set
p/n: 20-2481-33
This Spring Shackle Bushing Set is for the front of the rear leaf spring. Two (2) kits required per car.
Radiator Splash Shield
p/n: 20-0509-45
This Radiator Splash Shield is a lower radiator to grille splash pan seal. Twenty-three and one half (23-1/2) inches long.
Lower Tailgate Outer Weatherstrip
p/n: 70-4810-84
This Lower Tailgate Outer Weatherstrip is designed from the original part for superior fitment and seal. The weatherstrip mounts on the outer bottom of the tailgate.
Body Mounting Pad
p/n: 50-0361-48
Pad, body mounting. Required replacement for body-off restorations. Constructed of high quality rubber for long lasting durability. Two inch (2") square by fifteen sixteenths inch (15/16) inside hole diameter by one fourth inch (1/4") height.
Gearshift Bushing
p/n: 60-0237-24
This Gearshift Bushing is fully molded and designed from the original part for superior fitment and seal. This bushing is made from high-quality EPDM dense rubber to provide excellent durability. Designed for the gearshift shaft lever, large type.
Dimmer Switch Grommet
p/n: 40-0083-88
This Dimmer Switch Grommet is used during carpet installations in automotive restorations. Made from high-quality EPDM dense rubber to provide excellent durability. Includes a wide flange for floor dimmer switch fitments.
Door Handle Gasket Set
p/n: 70-0572-69
This Door Handle Gasket Set is designed from the original part for superior fitment and seal. This four (4) piece gasket set will do two (2) doors.
Clutch or Brake Pedal Pad
p/n: 20-0848-22
This reproduction Clutch and/or Brake Pedal Pad slips over the full perimeter of the pedal for a precise, factory fit. A perfect reproduction to replace worn original pedal pads. Manufactured in quality black rubber.
Clutch and Brake Pedal Bump Stops
p/n: 70-4805-24
This Clutch and Brake Pedal Bump Stop pair is designed from the original part for superior fitment, finish and function. These rubber bumpers help align your brake and clutch pedals in the correct position, while also preventing rattles and squeaks.
Outside Door Handle Mounting Pads
p/n: 20-0568-69
This Outside Door Handle Mounting Pad set is designed from the original part for superior fitment and function. This four (4) piece molded rubber set does two (2) doors.
Shock or Stabilizer Link Cross Pin Bushing
p/n: 50-0220-32
This Shock or Stabilizer Link Cross Pin Bushing is designed from the original part for superior fitment and function. A rubber bushing for shock absorber link cross pin or stabilizer cross link pin.
1-3/8" Parking Brake Grommet
p/n: 50-0555-20
This Parking Brake Grommet is used to run the parking brake cable through the frame. Designed from original part for excellent workmanship.
Interior Dome Light Lens Gasket
p/n: 70-3102-17
This Interior Dome Light Lens Gasket is designed from the original part for superior fitment and seal. This quality reproduction gasket fits between the interior dome light lens and the dome light housing or bezel.
Vent Window Division Post Weatherstrip
p/n: 70-0040-56
This Vent Window Division Post Weatherstrip is an extruded thirty (30") inch rubber strip that may have to be glued to your old original division post seal core, or directly to the division post.
Hood Bumper
p/n: 50-0277-42
Bumper, hood side to fender ledge. Metal core molded in as original.Width: 1.875 inches. Height: .8125 inches.
Hood to Fender Bumper
p/n: 25-0068-42
This Hood to Fender Bumper is a quality reproduction of the original factory part. These rubber bumpers attach to the front fender to support / cushion the hood closure.
Window Sash Channel Weatherstrip
p/n: 20-3069-60
This Window Sash Channel Weatherstrip is designed from the original part for superior fitment and seal. Thirty six (36) inch long roll. One (1) roll required per window.
Tie Rod Dust Covers
p/n: 20-2484-36
This Tie Rod Dust Cover, drag link seal, is sold as a four (4) piece set. The seals are designed from originals for proper fitment.
Headliner Retainer Clip
p/n: 20-0576-88
Clips, roof headliner and seal retainer. Set of sixteen (16) pieces.
Exhaust Tailpipe Hanger Strap
p/n: 60-0308-13
This Exhaust Tailpipe Hanger Strap is made from high-quality rubber for a precise, factory like fit for your classic vehicle. Muffler/tailpipe system, reproduction strap type is manufactured to OEM specifications.
Rear Spring Pad
p/n: 30-0452-32
Insulator, rear spring leaf clip. Seven and one half (7-1/2) inch long, customer may trim for shorter lengths. May use up to eight (8) per car.
Front or Rear Axle Bumper
p/n: 20-1576-33
This Front or Rear Axle Bumper is designed from the original part for superior fitment, finish and function. An exact reproduction of original. Typically order two per vehicle.
Starter Pedal Bellows
p/n: 60-0210-21
Bellows, starter pedal shaft to floorboard. Three eighths (3/8) inch top hole with three (3) inch height.Width: 2.875 inches. Height: 3.0 inches.
Lower Suspension Arm Dust Seal
p/n: 70-0624-32
Dust seal, "O" ring. Lower suspension arm pin bushing. Four (4) required per car.Height: .25 inches.
Parking, Signal or Backup Light Lens Gaskets
p/n: 50-0381-16
This front Parking and Turn Signal Light Lens Gasket pair is designed from the original part for superior fitment and seal. This reproduction gasket fits between the Light Lens and the Light Housing or Bezel. Also fits Backup Light Lens on cars with optional Backup Lights.
Parking/Backup Light Lens Gasket
p/n: 70-1272-16
Gasket, parking light lens and backup light lens. Die cut from one eighth (1/8) inch rubber.
Gearshift Knob
p/n: 20-0583-24
This black floor shift lever Gearshift Knob is designed from the original part for a superior fit and finish. This reproduction part is a direct screw on replacement for that broken, aged-out original knob.
Steering Column Floorplate
p/n: 20-0548-88
Seal, steering column, brake and clutch arms to floor. Column shift models. Installs under metal plate.
2-1/2" Tan Bow Drill Cloth Tape
p/n: 70-1173-65
This Bow Drill Cloth Tape is used for covering convertible side window weatherstrip. Tan in color and available in a five (5) foot roll.
Clutch and Brake Pedal Pads
p/n: 20-1563-22
This reproduction Clutch and Brake Pedal Pad pair screws to the pedal arms for a precise, factory fit. With authentic concentric circle design, pads are a perfect reproduction to replace worn original pedal pads.
Body Mounting Pad
p/n: 20-0553-48
Pad, front of cab to frame. Lower. Fully molded rubber with locating collar.
Steering Column Floorplate
p/n: 20-0549-88
Seal, steering column, brake and clutch arms to floor. Floor shift models.
Rear Stabilizer Bushing
p/n: 70-1967-33
Bushing, rear stabilizer. Four (4) are required per car. Fully molded rubber. One and one half inch (1 1/2") outside diameter by five eighths inch (5/8") inside hole diameter by seven eighths inch (7/8") height.
1-3/16" Standard Grommet
p/n: 32-0328-54
This Standard Grommet is fully molded and designed from the original part for superior fitment and seal. This grommet is made from high-quality EPDM dense rubber to provide excellent durability.
Body Mounting Pad
p/n: 50-0096-48
Pad, body mounting. Fully molded rubber with steel core and locating collar.
Rear coil spring pad
p/n: 50-0304-35
Insulator, rear coil spring clamp bolt (upper end). Two (2) per car. Fabric reinforced rubber as original.
Antenna grommet
p/n: 70-1865-19
Grommet, antenna mounting. Fits all models with power antenna. Used with our #70-0756-19.
Axle Rebound Pad
p/n: 20-0833-32
Bumper, front axle. Fully molded with retaining bolt. Typically order two (2) per truck.
Solenoid Plunger Boot
p/n: 60-0567-21
Boot, solenoid plunger, starter switch at starter.Height: 1.625 inches.
1-11/16" Firewall Grommet
p/n: 60-0057-21
This Firewall Grommet is used to run the wiring harness through the firewall. Designed from original parts for excellent workmanship.
Bed Frame Mounting Pad Set
p/n: 20-0572-48
This eight (8) piece Bed Frame Mounting Pad set is designed from the original parts for superior fitment and function. These mounting pads mount under the bed on all bolt mounting points.
Window Stop Stem Bumper
p/n: 33-0675-62
Cushion (stem bumper), window stop, lower. For front and rear door, rear side and quarter windows as required.
Vent Window Rebuild Set
p/n: 70-4801-70
This Vent Window Rebuild Set includes glass setting tape (1/16 thick), hinge pivot step rivet pair, and a rivet peening punch. The set has enough materials for both the passenger side and driver side vent window assemblies.
2-1/2" Black Bow Drill Cloth Tape
p/n: 70-1172-65
This Bow Drill Cloth Tape is used for covering convertible side window weatherstrip. Black in color and available in a five (5) foot roll.
Hood Bumper
p/n: 50-0159-42
Bumper, hood ledge corner at shroud.Width: 1.25 inches. Height: .5 inches.
Hood to Fender Bumper
p/n: 30-0304-42
This Hood to Fender Bumper is a quality reproduction of the original factory part. These rubber bumpers attach to the front fender to support / cushion the hood closure. Six (6) required per car.
Bumper - LH Back Door
p/n: 60-0333-71
A rubber Left-Hand Back Door Bumper. Dovetail to be used with old casing.
Shift Linkage Repair Set
p/n: 20-2460-26
This column Shift Linkage Repair set is designed from the original parts for superior fitment and function. This repair set replaces worn or missing bushings at the four linkage points in the column shift mechanism.
Accelerator Hinge Grommet
p/n: 30-0539-41
Grommet, accelerator pedal hinge to floorboard. Length: 3.50 inches. Width: 2.50 inches.
Firewall Grommet
p/n: 70-1010-19
This Firewall Grommet is used to run the vacuum antenna line through the firewall. Designed from original part for excellent workmanship.
1-1/4" Firewall Grommet
p/n: 70-0198-20
This Firewall Grommet is used to run the parking brake cable through the firewall. Designed from the original part for excellent workmanship.
Air Duct Ventilator Connector
p/n: 20-2964-31
This Air Duct Ventilator Connector is designed from the original part for superior fitment and function. Two (2) required per car.
Hood Bumper Set
p/n: 20-0545-42
This six (6) piece Hood Bumper set is designed from the original parts for superior fitment and function. This set fits F Series Trucks.
Cowl Vent Gasket
p/n: 20-0556-54
This Cowl Vent Gasket is designed from the original part for superior fitment and seal. Manufactured to OEM specifications to install for an authentic fit and finish.
Steering Column Floorplate
p/n: 20-1694-88
Seal, steering column tube. Installs on top of floor mat.
Hydraulic Pump Mounting Pad
p/n: 70-0986-62
Mounting bracket and pad, for hydraulic pump. Number used as required.Length: 1.75 inches. Width: .8125 inches.
Firewall to Hood Weatherstrip - Cowl Lacing
p/n: 20-3006-43
This Firewall to Hood Weatherstrip - Cowl Lacing is designed from the original part for superior fitment and seal. This seal mounts with installation tacks at the rear of the engine bay firewall directly to the body.
Hydraulic Pump Mounting Pad
p/n: 70-1610-67
Cushion mount, hydraulic pump.Width: .6875 inches. Height: 1.0 inches.
Steering Column Floorplate
p/n: 20-3158-88
Seal, steering column to floor. Installs under floor mat.
Battery Clamp Cover
p/n: 70-0095-21
This Battery Clamp Cover helps to protect the nearby metal and finish. Fully molded from high-quality EPDM rubber to ensure durability. Good copy from an original part.
Quarter Window Vertical Leading Edge
p/n: 70-0141-58
This quarter to side window Vertical Leading Edge Weatherstrip pair is designed from the original part for superior fitment and seal. Slides into metal retaining channel attached to rear side window and seals between the front door window and the rear quarter window.
Hydraulic Pump Mounting Cushion
p/n: 70-0852-67
This Hydraulic Pump Mounting Cushion is designed from the original part for superior fitment and function. Used on models with hydraulic window lifts or a hydraulic convertible top. Two (2) to three (3) required per car.
Stabilizer Bar End Link Set
p/n: 60-0221-33
Twenty-two (22) piece Stabilizer Bar End Link set for both sides of one (1) vehicle, fits front or rear bar. Order two (2) sets for vehicles with front and rear stabilizer bars. Hex head bolt 3/8"-16 NF x 6-15/16" long. Comes with metal sleeve, metal cup washers and rubber grommets.
Brake Master Cylinder Push Rod Boot
p/n: 60-0180-24
This Brake Master Cylinder Push Rod Boot is made from high-quality Nitrile rubber for a precise, factory like fit for your classic vehicle. Manufactured to OEM specifications to install for an authentic fit and finish.
Battery Hole Cover Seal
p/n: 20-0555-21
This Battery Hole Cover Seal is designed from the original part for superior fitment and seal. This part seals the battery hole cover to the vehicle floor.
Spring shackle bushing
p/n: 70-0444-32
Bushing, rear spring shackle, upper. Four (4) required per car.
Starter Button Cover
p/n: 60-0166-21
Cover, starter pedal button. Rubber slip over type for old metal. Two (2) inch outside diameter. If car doesn't have old metal, see our #60-0322-21.
Door Handle Gasket Set
p/n: 50-0322-69
This Door Handle Gasket Set is designed from the original part for superior fitment and seal. This six (6) piece gasket set will do two (2) doors.
Vent Window Division Bar Weatherstrip
p/n: 70-1432-56
This Front Vent Window Division Bar Weatherstrip is designed from the original part for superior fitment and seal. A single 32" inch (approximate) length of original cross-section extruded rubber.
Body Mounting Pad
p/n: 50-0477-48
Pad, body mounting. Fully molded rubber with metal core & locating collar.
1-7/16" Firewall Grommet
p/n: 60-0276-45
This Firewall Grommet is used to run the throttle rod and tube, oil pressure gauge pipe, heat indicator tube, and choke rod through the firewall.
Body Mounting Pad
p/n: 70-1429-48
Pad, body mounting. Fully molded rubber with metal core and rubber locating collar. Also used for radiator cradle to frame. Eight (8) to ten (10) required per car. Two and one fourth inch (2 1/4") outside diameter by one and one sixteenth inch (1 1/16") l
Hood Bumper Set
p/n: 33-0680-42
This eight (8) piece Hood Bumper set is designed from the original parts for superior fitment and function.
Lower Rear Engine Mount
p/n: 20-0584-11
This Lower Rear Engine Mount is designed from original part for correct fitment and function. Made of a quality dense rubber for durability and proper engine vibration isolation. Two (2) required per truck.