Please click on the part name in red in order to get a complete description.
Convertible roof rail weatherstrip. This part fits on the folding roof of the vehicle and seals the side window when the window is fully raised.
Front door edge weatherstrip kit. This part is the primary door to body weatherstrip. This includes one pair of #70-0857-73 which seals the lock side of the door to the body, #70-0530-73 which seals the vent window to the pillar, #50-0219-73 front door op
This front door vent window weatherstrip kit is a six (6) piece set that contains the main vent window seals, base extensions, and division post seals. All of the pieces were designed from original parts for a precise, factory fit.
Conduit, taillight wiring. One (1) pair each of two (2) different lengths. Four (4) piece set.
This windshield gasket mounts around the full perimeter of the front glass and has properly molded corners for a precise, factory fit. It also has molded sections for the wiper transmissions and the slot to accommodate the outer edge's decorative molding.
This front door vent window weatherstrip set contains the main seals for the vent windows and the base extension pieces for the frame. They are designed and molded from original parts for superior fitment and seal.
Weatherstrip, front door lock pillar. Ready to install with molded ends.Length: 36.0 inches. Width: .625 inches. Height: .625 inches.
Weatherstrip, door bottom (1951-2nd type). Molded left and right, overall length forty (40) inches.
Weatherstrip, front door. Upper on edge of door or body opening. Molded ends, right and left.
Bumper, rear axle. Revulcanization service only.Height: 3.5 inches.
Front motor mount. Revulcanizing core exchange only. Send in both pairs of the two piece cores when ordering.
This trunk weatherstrip set is designed from original parts for superior fitment and seal. The set contains the strips and corners that mount to the body and the strip that mounts to the lid.
Pad, taillight bodies to fender. Correct molded part with correct beading. Four (4) required per car.
Support pad, transmission mount (insulator). Revulcanization service only.Length: 5.0 inches. Width: 2.0 inches.
Support, transmission (insulator). Revulcanization service only. See also our #50-0262-25, many models use both.Length: 5.0 inches. Width: 1.875 inches.
Pad, transmission mounting, thrust. Revulcanization service only. One (1) per car required. See also our #50-0263-25. Many models use both.Length: 7.
Retainer, torque ball, heavy steel jacket with molded rubber inner collar. Revulcanization service only.
Boot, taillight and turn signal wiring. Excellent quality tubing with correct molded ends. Overall length 10". Two (2) pair required per car.
Weatherstrip, body hinge pillar to door, bellows type seal.
Run channel, front door window, for full length of division bar (approximately twenty nine (29) inches). Rigid, bright beaded edge, mohair lined channel, die trimmed and formed at top.
Bumper, rear axle stop. Molded left and right. Revulcanization service only.
Welting, fender, bright chrome vinyl, three sixteenths (3/16) inch bead, one and one half (1-1/2) inch width. Superior quality. Fifty (50) foot roll. Typically used to attach four (4) fenders to body. For twenty five (25) foot roll see #70-1101-44.
These trunk weatherstrip corners are designed from the original part for superior fitment and seal. The seals mount to the front corners of the trunk directly to the body.
Weatherstrip, hood to cowl. An exact reproduction of the original profile. This seal mounts at the rear of the engine bay directly to the body.
Bumper, door side. Square type held by four (4) screws, metal core as original.
Pad, rear compartment lid emblem.Width: 16.5 inches.
Boot, torque ball.Height: 2.375 inches.
Kit, stabilizer bar link assembly. Twenty two (22) piece set for both sides of one (1) car, front and rear. (Order 2 sets if you need both). Hex head bolt. 5/16"-24nf x 7-5/8" lg. Comes with metal sleeve, cup washers and rubber grommets.
Insulators, rear coil spring. Fabric reinforced rubber as original. One (1) pair per car.
Bumper, side window glass in vent frame at top, right and left, brass core.Length: 1.625 inches.
Gasket, rear stop and turn signal. Four (4) piece set required per car.
Channel, rigid run, window division bar. Stainless beaded edge, mohair-lined, exact replacement for rear side of division bar.
Weatherstrip, door window inner and outer, front and rear doors. Seven sixteenths (7/16) inch wide, with chrome bead, mohair faced, flexible. Two (2) three (3) foot strips. Bend to fit.
Headlight door to lens seal. Molded without wire. Single lip type for sealed beams.
Bumper, front suspension, upper arm.Height: 2.0 inches.
Front vent window division post seal. Fully molded with metal core and attaching tabs.
Bushings, front stabilizer shaft-to-frame or stabilizer shaft, front or rear. Fully molded rubber. One and one half inch (1 1/2") length by one and one half inch (1 1/2") width by eleven sixteenths inch (11/16") inside hole diameter by one and one half in
Pad, brake and clutch pedal. Brown rubber. For black see our part #50-0054-22. Perfect copy, fine detail.Color:brown Width: 3.125 inches.
Weatherstrip, inner and outer for sliding quarter window, chrome beaded, mohair faced, flexible stock. May be formed to required outline. Six (6) foot strip.
Welting, fender, bright chrome vinyl, three sixteenths (3/16) inch bead, one and one half (1-1/2) inch width. Superior quality. Twenty five (25) foot roll. Typically used to attach two (2) fenders to body. For fifty (50) foot roll see our #70-1102-44.
Weatherstrip, front door opening, front body hinge pillar, lower. Extruded sponge to original configuration. Two (2) required per car.Width: .875 inches.
Bumper, front suspension, lower arm. Steel core, with threaded stud, as original. Two (2) per car required.
Gasket, front parking and signal light to fender. One (1) pair per car. Fits between signal lamp body and headlamp to fender adapter.Width: 4.0 inches.
Seal, heater control valve. High quality sponge rubber designed to cushion heater control valve and keep out noise and water.
Headlight body mounting gasket. Rubber.
Gasket, headlight door parking lens. Constructed out of soft durable rubber.Height: .375 inches.
Sash channel, side window glass. U-shaped steel channel only, no filler. Will require that you attach your own window regulator cam to underside as required.
Pedal pad, power brake only, slip-over.Width: 4.75 inches.
Channel, rigid run, lower side window below beltline, zinc plated steel with black cloth lining, one half (1/2) inch deep by one half (1/2) inch wide, fifteen (15) inches long.
Bumper, quarter window at lock pillar.Width: 1.125 inches.
Tape, black bowdrill cloth. Adhesive backed, used to create cloth cover surface for side rail weatherstrips typically. Five (5) inches by five (5) foot roll. Pressure sensitive, for covering convertible side window weatherstrip such as our #70-1170-99 or
Grommet, brake and clutch pedal floor seal.Width: 1.8125 inches. Height: 2.375 inches.
Gasket, front parking lens. High quality sponge rubber better than original. One (1) pair per car.Width: 3.375 inches. Height: 2.625 inches.
Pad, parking brake pedal. Without "PARK" written on pad. Black only. For pedal pad with "PARK" written on pad see our #50-0405-22.Height: 2.0 inches.
Pad, brake and clutch pedal. Black rubber. For brown see our part #50-0054-89. Perfect copy, fine detail.Width: 3.125 inches. Height: 2.125 inches.
Insulators, front coil spring. Fabric reinforced rubber as original.
Seal, reflector signal, between taillights. With correct slits for tabs on reflector. One (1) pair required per car.
Boot, starter solenoid.
Grommet, spark plug wire. Trapezoidal style under spark plug cover flange at right end of both sides. One (1) pair required per car with our #50-0345-21.
Weatherstrip, front bow of convertible. Sponge rubber extrusion of correct dimensions.Length: 60.0 inches. Width: .8125 inches.
Grommet, spark plug wire. Oblong style for spark plug wire clip at right rear of head. One (1) pair required per car with our #50-0346-21.Width: 1.
Boot, battery cable at starter solenoid.Width: 2.75 inches.
This Leading Edge Vertical Weatherstrip seal pair is designed from the original part for superior fitment and seal. Slides into metal retaining channel attached to rear side window and seals between the front door window and the rear quarter window.
Seal, heater control valve. High quality sponge rubber designed to cushion heater control valve and keep out noise and water. For all except right-hand drive.
T-nut, trunk bumper in gutter at sides, brass core tapped 10-32 thread. Two (2) required per car. For models having partial weatherstrip in gutter of body.
Pad, body mounting. Fully molded rubber with metal core & locating collar. One and seven eighths inch (1 7/8") outside diameter by one and one eighths inch (1 1/8") locating collar outside diameter by three fourths inch (3/4") locating collar inside diame
Gasket set, door handle, outside. For front and rear door if necessary. Six (6) piece set for two (2) doors.
Pad, mounting, hydraulic pump. Used on models with hydraulic window lifts or hydraulic convertible top. Two (2) to three (3) required. per car.
Cover, battery clamp. Control unsightly sulfate buildup. Help protect the nearby metal and finish. Good copy from original part.Length: 3.5 inches.
Tape, black bowdrill cloth. Adhesive backed, used to create cloth cover surface for side rail weatherstrips typically. Two and one half (2-1/2) inches by five (5) foot roll. Pressure sensitive, for covering convertible side window weatherstrip such as our
Bumper, hood ledge corner at shroud.Width: 1.25 inches. Height: .5 inches.
Gasket, wiper transmission. Replaces #4573556.
Pad, body mounting. Fully molded rubber with steel core and locating collar. Two inch (2") square by one and one eighth inch (1 1/8") locating collar outside diameter by eleven sixteenths inch (11/16") locating collar inside diameter by one half inch (1/2
Insulator, rear coil spring clamp bolt (upper end). Two (2) per car. Fabric reinforced rubber as original.
Grommet, for various usage. Sheet Metal Hole: 11/16" Center Hole: 3/8" Outside Diameter: 1-3/16" Slot Width: 1/16"
Tape, brown (tan) bowdrill cloth. Adhesive backed, used to create cloth cover surface for side rail weatherstrips typically. Two and one half (2-1/2) inches by five (5) foot roll. Pressure sensitive, for covering convertible side window weatherstrip such
Gasket, front parking and signal light lens gasket. Backup lens on cars with optional backup lenses.
Pad, body mounting. Required replacement for body-off restorations. Constructed of high quality rubber for long lasting durability. Two inch (2") square by fifteen sixteenths inch (15/16) inside hole diameter by one fourth inch (1/4") height.
Masticated sheet. Three thirty seconds (3/32) inch thick rubber sheet containing random milled cotton cord reinforcement for front end splash aprons, etc. This product is a four (4) foot wide roll, and will only be sold in four (4) square foot multiples
Grommet, firewall, oil pressure and water temperature, or washer vacuum hose.
Grommet, firewall, windshield washer hose.
Gasket set, rear license light assembly. One (1) rubber ring and one (1) cork rubber gasket comprise set.
Bumper, hood to radiator grille frame. Four (4) per car, normally.
Bushing, rear axle, anti-sway rod ends. Fully molded rubber. Four (4) required per car. One and one fourth inch (1 1/4") top outside diameter by one and one eighth inch (1 1/8") bottom outside diameter by five eighths inch (5/8") inside hole diameter by t
Bumper, hood in fender flange.Width: 1.0 inches. Height: 1.5 inches.
Bumper, hood to fender. Uses four (4) per car for most models.Width: 1.375 inches. Height: 1.25 inches.
Bumper, glove box check link. Fits on glove box door arm as needed.Length: .75 inches. Width: .5625 inches. Height: .3125 inches.
Cushion (stem bumper), window stop, lower. For front and rear door, rear side and quarter windows as required.
Dust cover, tie rod ends.
Grommet, shift lever insulator. One (1) per car. Three eighths (3/8) inch inside diameter by five eighths (5/8) inch barrel by one half (1/2) inch long.
Anti-rattle roller, side windows. Rubber only, replaces original perfectly and easily. Fits both styles of brackets.
Knob or push button for inside door lock, fits over 1/8" steel rod to door lock. Hard brown rubber, may be lacquered other colors as required.
Trunk weatherstrip made from high quality EPDM sponge rubber. Excellent for use on many different vehicle models.
This weatherstrip was designed from an original part for a specific application but has many uses outside of its original purpose. The seal is structured to be applied to the body of the car.
Liner, mohair. Liner with a rubber backing. Apply with adhesive to division bars and channels. Helps reline guide bars on lock side of hardtops and convertibles.
Weatherstrip, door edge. Fine grain sponge. Larger type used on most GM cars this period. Width: 13/16". Height: 11/16".
Grommet, shock and stabilizer link. Eight (8) required per car. Fully molded rubber with locating collar. One and one sixteenth inch (1 1/16") outside diameter by nine sixteenths inch (9/16") locating collar outside diameter by three eighths inch (3/8") i
Trunk weatherstrip made from high quality EPDM sponge rubber. Excellent for use on many different vehicle models.
Mounting cushion, vacuum pump. Three (3) per car required.Width: .625 inches.
Bumper, license plate. Fully molded rubber.