Search Results
Side window run channel kit
p/n: 20-0564-58
Complete window channel and felt kit. Includes vent window division post channels, glass run channels, and inner and outer windowfelts. Completes both doors.
Front Door Vent Window Kit
p/n: 90-0305-90
This front door vent window weatherstrip kit is a four (4) piece set that contains the main vent window seals and division post seals. All of the pieces were designed from original parts for a precise, factory fit.
Front Door Vent Window Weatherstrips
p/n: 20-0560-55
These front door vent window weatherstrips are the main seals needed to replace the rubber on your vent windows. They are designed and molded from original parts for superior fitment and seal.
Windshield Gasket
p/n: 20-0557-50
This windshield gasket is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the front glass and has vulcanized, or bonded, ends which means no cutting or splicing is required for installation.
Front Door weatherstrip
p/n: 20-0559-72
Door edge weatherstrip. This part is the primary door to body weatherstrip.
Flexible run channel
p/n: 20-0510-58
Channel, door glass run. Stainless beaded edge. Includes clips pre-installed. Enough for one door only.
Vent division bar assembly
p/n: 20-0566-56
Assembly, complete division bar. Left-side only. Ready to install. Comes complete with brackets and back of vent window seal.
Vent division bar assembly
p/n: 20-0565-56
Assembly, complete division bar. Right-side only. Ready to install. Comes complete with brackets and back of vent window seal.
Window felt weatherstrip
p/n: 80-0630-57
Original equipment style side window horizontal seal kit (also known as beltline weatherstrip). Kit includes inner and outer felt beltline weatherstrip for each door and quarter windows. These strips wipe the side windows when the glass is lowered. They c
Rear Window Gasket
p/n: 20-0571-81
This rear window gasket is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the back glass and has vulcanized, or bonded, ends which means no cutting or splicing is required for installation.
Brake and clutch pedal pad
p/n: 20-0494-22
Pads, brake and clutch pedal. Three and one half (3-1/2) inch diameter.
Motor mount
p/n: 20-0515-11
Mount, upper motor. One (1) required per truck. 1953-56: F100-F350 239 & 272 V8 and 1953-56: F100 & F250 215 & 223 6 cylinder.
Radiator mounting pad kit
p/n: 20-0570-45
Kit, radiator support to frame pad. Includes: two (2) center pads, two (2) outer support pads, bolts, nuts, lock washers.
Fabric Hood Lacing
p/n: 20-0354-42
Lacing, hood cowl. Forty nine (49) inches long. Cloth anti-squeak material where hood rests on cowl. Includes tacks.
Vent division bar weatherstrip
p/n: 20-0562-56
Front vent window division post seal. This part fits opposite the glass run channel and seals the vent window when the vent is closed.
Gearshift grommet
p/n: 20-2460-26
Repair kit, gear shift lever grommet. Column shift only. Two (2) kits required.
Axle rebound pad
p/n: 20-0833-32
Bumper, front axle. Fully molded with retaining bolt. Typically order two (2) per truck.
Body mounting pad
p/n: 20-0553-48
Pad, front of cab to frame. Lower. Fully molded rubber with locating collar. One and five eighths inch (1 5/8") outside diameter by three fourths inch (3/4") locating collar outside diameter by one half inch (1/2") locating collar inside hole diameter. On
Radiator splash shield
p/n: 20-0509-45
Seal, lower radiator grille splash pan to radiator. Twenty three and one half (23-1/2) inches long.
Vent division bar weatherstrip
p/n: 20-0708-56
Front vent window division post seal. Extruded rubber strip only that will have to be attached to division post.
Glovebox and fuel door bumper
p/n: 20-1220-88
Bumpers, glovebox and/or fuel filler door. Used as glove box door bumpers for all models listed, used as fuel door bumper for 1950-51 cars and 57-59 retractables only.
Body Hole Plug
p/n: 20-1041-21
Plug, cowl and floor pan. This body plug covers a sheet metal hole that is one and one seven eighths (1-7/8) inch in diameter.
Body mounting pad
p/n: 20-0458-48
Bushings, rear of cab to frame suspension arm. Set of four (4) pieces.