This Rear Window Gasket Set contains the rear window gasket itself and the locking strip. The gasket has the divider bars molded directly into it and has molded corners for a precise, factory fit. It also has the slot to accommodate the outer edge's decorative molding.
This Front Door Weatherstrip set is for the front doors. The set includes weatherstrip for door perimeter and hinge pillars.
This Windshield Gasket Set contains the windshield gasket itself and the locking strip. The seal mounts around the full perimeter of the front glass and has properly molded corners. It also has the slot to accommodate the outer edge's decorative molding.
Weatherstrip, front door hinge pillar.
This four (4) piece Front Door Vent Window Set contains the main vent window seals and division post seals. All of the pieces were designed from original parts for a precise, factory fit.
Weatherstrip, rear door kit. Includes weatherstrip for door perimeter and hinge pillars.
This rear door vent window weatherstrips pair is designed from the original parts for superior fitment and seal.
Weatherstrip, rear door hinge pillar. Attaches to body on hinge pillar. Molded without metal core.
These Front Door Vent Window Weatherstrips are the main seals needed to replace the rubber on your vent windows. They are designed and molded from original parts for superior fitment and seal.
This Revulcanization Service Only is designed to restore your Front Engine Support Mount to a like new original condition. Service requires your metal core. Please call or email for more service details and ordering.
This Revulcanization Service Only is designed to restore your Rear Engine Support Mount to a like new original condition. Service requires your metal core. Please call or email for more service details and ordering.
Pad, accelerator pedal. Revulcanization service only.
Bumper, front spring compression, lower arm. Steel core, retained by clip (not included).Height: 2.625 inches.
This Peel-N-Stick Trunk Weatherstrip is designed for superior fitment and seal. The seal mounts around the full perimeter of the trunk directly to the body. Easy to install 3M Peel-N-Stick backing provides superior adhesion for reliable performance.
Bumper, front spring rebound, lower.Width: 2.125 inches. Height: 2.25 inches.
This Trunk Weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the trunk directly to the body.
This Hood to Cowl Weatherstrip is designed from the original part for superior fitment and seal. Fully molded with carrot-bumper retainers.
Grommets, rear door vent divider post, upper and lower, right and left. 4 piece set.
Grommet, steering column at floorboard.Length: 4.50 inches.
Cover, power brake pedal, with "Easamatic power brake" logo. Fully molded with script just like original.
Bumper, front spring rebound, upper.Height: 2.25 inches.
Pad or Gasket, taillight to body. One (1) pair required per car, sold only in pairs.
Retainer, intermediate bearing. All models with two piece driveshafts.
Bumper, rear axle rebound.Length: 3.0 inches. Width: 2.375 inches. Height: 1.6875 inches.
Bearings or bushings, front stabilizer rod. One (1) pair used per vehicle. Fully molded rubber. One and nine sixteenths inch (1 9/16") length by one and nine sixteenths inch (1 9/16") width by three fourths inch (3/4") inside hole diameter by one and elev
Front vent window division post seal. Fully molded with metal core and attaching tabs.
This Rear Shield to Bumper Seal is made of high quality EPDM dense rubber. The seal is designed from an original part so it fits correctly. Overall length is seven (7) feet.
Division post seal pair for rear door vent window. Made from top quality rubber to ensure durability and proper seal. Designed from original part so it fits correctly.
This Back-Up Light To Body Gasket pair are top quality molded rubber seals manufactured to authentic original dimensions.
Bushings, front stabilizer rod end. One (1) pair required per car. Fully molded rubber. One and one half inch (1 1/2") length by one and one eighth inch (1 1/8") width by three fourths inch (3/4") inside hole diameter by one and one half inch (1 1/2") hei
Grommet, ignition cable.Length: 2.125 inches. Width: 1.50 inches.
These Window Felt Beltline Weatherstrips are sold as a three (3) foot pair. The beltline is used for side windows inner and/or outer, front and/or rear doors. Available in a 3ft pair.
Gaskets, headlight body mounting to fender. Cut to exact size as original.
Headlight body mounting gasket. Rubber.
Grommet, heater core at firewall.Length: 3.5625 inches. Width: 2.25 inches.
Grommet, handbrake rod to dash.Height: 1.875 inches.
Grommet, wiring harness.
This steering column Gearshift Boot is designed from the original part for superior fitment, finish and function. Brown rubber. Two and one quarter (2-1/4) inches long.
Anti-rattler, front stone shield. Insulates the front stone shield from the front bumper. Six (6) piece set.
Pad, rear spring insulator. Order four (4) per car.Length: 4.75 inches. Width: 2.875 inches.
Tail Light Lens Gasket
This steering column Gearshift Boot is designed from the original part for superior fitment, finish and function. Black rubber. Two and one quarter (2-1/4) inches long.
Grommet, carpet. Floor front carpet grommet use for power brake hole.
Pad, fender mounted antenna.Length: 2.5 inches.
Pad, body mounting. Fully molded rubber with metal core and rubber locating collar. Also used for radiator cradle to frame. Eight (8) to ten (10) required per car. Two and one fourth inch (2 1/4") outside diameter by one and one sixteenth inch (1 1/16") l
This black rubber Battery Clamp Cover helps to protect the nearby metal and finish. Good copy from an original part. Length: 3-1/2" inches.
Grommet, accelerator pedal hinge to floorboard.Length: 3.50 inches. Width: 2.50 inches.
This Hood to Fender Bumper is a quality reproduction of the original factory part. These rubber bumpers attach to the front fender to support / cushion the hood closure. Six (6) required per car.
Grommet, antenna mounting. Fits all models with power antenna. Used with our #70-0756-19.
Bushing, rear stabilizer. Four (4) are required per car. Fully molded rubber. One and one half inch (1 1/2") outside diameter by five eighths inch (5/8") inside hole diameter by seven eighths inch (7/8") height.