Please click on the part name in red in order to get a complete description.
Cover, starter pedal button. Rubber slip over type for old metal. Two (2) inch outside diameter. If car doesn't have old metal, see our #60-0322-21.
Grommet, emergency brake cable through firewall. Excellent reproduction of original.Width: 2.5 inches.
Seal, battery hole cover to floor.
Hose, cowl vent drain.Length: 7.25 inches.
Seal, radiator air deflector to hood.
Pad, mounting, hydraulic pump. Used on models with hydraulic window lifts or hydraulic convertible top. Two (2) to three (3) required. per car.
Cover, battery clamp. Control unsightly sulfate buildup. Help protect the nearby metal and finish. Good copy from original part.Length: 3.5 inches.
Seal, steering column to floor. Installs under floor mat.
Rubber, garnish molding to dash. Eighty two (82) inches long.
Kit, cowl lacing. Includes tacks to install.
Cushion mount, hydraulic pump.Width: .6875 inches. Height: 1.0 inches.
Cover, rocker panel inner dust shield. Fully molded with proper attaching teeth and flap.
Insulator, gear shift.
Insulator, transmission gear shift column lever.
Seal, steering column tube. Installs on top of floor mat.
Seals, taillight lamp housing.
Bushing, control arm. Two (2) required per side.
Gasket, cowl vent.
Bumper set, hood.
Bushings, stabilizer bar to frame. One (1) pair required per car.
Grommet, accelerator pedal hinge to floorboard.Length: 3.50 inches. Width: 2.50 inches.
Grommet, speedometer cable line through firewall. Excellent reproduction of original.
Grommet, vacuum hose and ignition resistor wire through firewall. Excellent reproduction of original.
Grommet, oil pressure and temperature line through firewall. Excellent reproduction of original.
Bumpers, seat back for second seat.
Gaskets, ventilator air valve.1952-54: 1 pair required. 1955-56: 2 pair required.
Repair kit, gear shift lever grommet. Column shift only. Two (2) kits required.
Bumper, dovetail, left hand back door, rubber only. To be used with old casing.
Bumper, hood, on side of fender. Six (6) required per car.Length: 1.0 inches. Width: 1.375 inches.
Tape, black bowdrill cloth. Adhesive backed, used to create cloth cover surface for side rail weatherstrips typically. Two and one half (2-1/2) inches by five (5) foot roll. Pressure sensitive, for covering convertible side window weatherstrip such as our
Grommet, wiring harness through firewall, for one and one fourth (1-1/4) inch hole in sheet metal.Height: .75 inches.
Cushion (stem bumper), window stop, lower. For front and rear door, rear side and quarter windows as required. (See sketch and our #33-0540-62).
Grommet, glove box link.Width: .625 inches.
Bumper, front axle. Fully molded with retaining bolt. Typically order two (2) per truck.
Gaskets, back-up light housing to body.
Kit, bed to frame pad. Set of eight (8) pads.
Bushing, control arm. Upper inner rear. One (1) required per side.
Bushing, control arm. Upper inner front. One (1) required per side.
Seal, hood front to top of radiator.
Boot, solenoid plunger, starter switch at starter.Height: 1.625 inches.
Bushing, spring shackle. Four (4) required.
Gaskets, taillight housing to body.
Vent window division post seal. Extruded thirty (30") inch rubber strip that may have to be glued to your old original division post seal core, or directly to the division post.
Grommet, antenna mounting. Fits all models with power antenna. Used with our #70-0756-19.
Pad, body mounting. Fully molded rubber with steel core and locating collar. Two inch (2") square by one and one eighth inch (1 1/8") locating collar outside diameter by eleven sixteenths inch (11/16") locating collar inside diameter by one half inch (1/2
Insulator, rear coil spring clamp bolt (upper end). Two (2) per car. Fabric reinforced rubber as original.
Bushing, rear stabilizer. Four (4) are required per car. Fully molded rubber. One and one half inch (1 1/2") outside diameter by five eighths inch (5/8") inside hole diameter by seven eighths inch (7/8") height.
Grommet, for various usage. Sheet Metal Hole: 11/16" Center Hole: 3/8" Outside Diameter: 1-3/16" Slot Width: 1/16"
Pad, brake and clutch pedal. Replacement type.
Pad, front of cab to frame. Lower. Fully molded rubber with locating collar. One and five eighths inch (1 5/8") outside diameter by three fourths inch (3/4") locating collar outside diameter by one half inch (1/2") locating collar inside hole diameter. On
Seal, steering column, brake and clutch arms to floor. Floor shift models.
Seal, steering column, brake and clutch arms to floor. Column shift models. Installs under metal plate.
Tape, brown (tan) bowdrill cloth. Adhesive backed, used to create cloth cover surface for side rail weatherstrips typically. Two and one half (2-1/2) inches by five (5) foot roll. Pressure sensitive, for covering convertible side window weatherstrip such
Knob, gear shift lever.
Dust seal, "O" ring. Lower suspension arm pin bushing. Four (4) required per car.Height: .25 inches.
Gasket, parking light lens and backup light lens. Die cut from one eighth (1/8) inch rubber.
Insulator (support). Muffler/tailpipe system, strap type as original. One and three fourths (1-3/4) inch by three and five eighths (3-5/8) inch.
Bellows, starter pedal shaft to floorboard. Three eighths (3/8) inch top hole with three (3) inch height.Width: 2.875 inches. Height: 3.0 inches.
Bumper, front or rear axle.Truck: Typically order two per truck.
Weatherstrip, window sash channel. Thirty six (36) inch long roll. One (1) required per window.Length: 36.0 inches.
Pad, fear of cab to frame suspension arm.
Pads, outside door handle. Pair does two (2) doors.
Bumper, front suspension upper.
Clips, roof headliner and seal retainer. Set of sixteen (16) pieces.
Insulator, rear spring leaf clip. Seven and one half (7-1/2) inch long, customer may trim for shorter lengths. May use up to eight (8) per car.
Gaskets, taillight lamp lens.
Seals, tie rod end. Four (4) piece set.
Bumper, hood to fender, side.Length: 1.1875 inches. Width: .8125 inches.
Grommet, parking brake cable through frame.
Bushing, for shock absorber link cross pin or stabilizer link cross pin.1931-36 Bushing, rubber, for shock absorber link cross pin, #41151.
Seal, outside door handle button.
Pads, outside door handle. Four (4) piece set.
Bushing, shock absorber link and rear stabilizer bar link.
Grommet, accelerator pedal rod through floorboard.
Grommet, dimmer switch for carpet application.
Pad, front mount antenna.
Pad, front of cab to frame. Upper.
Pad, body mounting. Required replacement for body-off restorations. Constructed of high quality rubber for long lasting durability. Two inch (2") square by fifteen sixteenths inch (15/16) inside hole diameter by one fourth inch (1/4") height.
Bushing, gearshift shaft lever, larger type. Three eighths (3/8) inch inside diameter by nine sixteenths (9/16) inch outside diameter barrel.Height: .
Knob, gear shift. Ball type. Fits models with column shift.
Masticated sheet. Three thirty seconds (3/32) inch thick rubber sheet containing random milled cotton cord reinforcement for front end splash aprons, etc. This product is a four (4) foot wide roll, and will only be sold in four (4) square foot multiples
Gaskets, parking light lens.
Seal, lower radiator grille splash pan to radiator. Twenty three and one half (23-1/2) inches long.
Bolt and bushing, front of rear spring. Two (2) kits required per car.
Seal, steering column at toe pan, sponge.Length: 5.375 inches. Height: .25 inches.
Gaskets, taillight lens to housing.
Pad, body mounting to chassis. Fully molded rubber. One and seven eighths inch (1 7/8") outside diameter by fifteen sixteenths inch (15/16") inside hole diameter by nine sixteenths inch (9/16") height.
Pad, body mounting to chassis. Fully molded rubber. One and seven eighths inch (1 7/8") outside diameter by eleven sixteenths inch (11/16") inside hole diameter by nine sixteenths inch (9/16") height.
Pad, several useages. Use as a body mounting pad or as a cushion for body mounting bolt. Fully molded rubber. Up to twenty (20) required per car. Two inches (2") outside diameter by three fourths inch (3/4") inside hole diameter by one half inch (1/2") he
Gasket set, front or rear doors. Six (6) piece set for two (2) handles.
Grommet, electric wire into light body under fenders, for headlights, taillights, some parking lights and auxiliary (fog) lights. Fits seven eighths (7/8) inch hole in light body. Two (2) to eight (8) per car as required.
Pad, body mounting to chassis. Fully molded rubber, square type. Six (6) or more are used per car. Two and three sixteenths inch (2 3/16") square by three fourths inch (3/4") inside diameter hole by one half inch (1/2") inch height.
Bumpers, tailgate chain. Fits in bracket.
Gasket, windshield wiper transmission mounting. Replaces #4597009. Two (2) required per car.
Bumper, hood to radiator grille frame. Four (4) per car, normally.
Bushing, rear axle, anti-sway rod ends. Fully molded rubber. Four (4) required per car. One and one fourth inch (1 1/4") top outside diameter by one and one eighth inch (1 1/8") bottom outside diameter by five eighths inch (5/8") inside hole diameter by t
Knob, inside door lock control, flexible rubber, black only.Height: 1.125 inches.
Cushion, used as either a body mounting pad or for all body bolt nuts, below brackets. Fully molded rubber. Two inch (2") outside diameter by one half inch (1/2") inside hole diameter by three eighths inch (3/8") height.
Grommets, front stone deflector to bumper arm anti-rattler. Four and one half (4-1/2) inch long. Two (2) piece set.
Gaskets, parking light lens.