Search Results
Glass Weatherstrip Kit
p/n: 90-3073-90
This kit includes the weatherstrip components needed for the glass on your restoration project.
Side Window Run Channel Kit
p/n: 90-0141-58
This ten (10) piece kit includes the inner and outer windowfelts, upper and lower rigid run channels, and flexible run channels needed to complete two (2) doors.
Rear Window Gasket
p/n: 50-0215-81
This rear window gasket mounts around the full perimeter of the back glass and has properly molded corners for a precise, factory fit.
Front Door Vent Window Set
p/n: 90-0418-90
This front door vent window weatherstrip set is a four (4) piece set that contains the main vent window seals and division post seals. All of the pieces were designed from original parts for a precise, factory fit.
Windshield Gasket
p/n: 50-0212-50
This windshield gasket is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the front glass and has vulcanized, or bonded, ends which means no cutting or splicing is required for installation. It also has the slot to accommodate the top edge's decorative molding.
Motor mount service
p/n: 25-0072-11
Insulator, cushion assembly. Engine mount at bell housing, right and left. Revulcanization service only.Length: 5.25 inches.
Motor mount service
p/n: 25-0059-11
Motor mounts, rear at transmission, right and left. Revulcanization service only.Length: 5.25 inches.
Front Door Vent Window Weatherstrips
p/n: 38-0081-55
These front door vent window weatherstrips are the main seals needed to replace the rubber on your vent windows. They are designed and molded from original parts for superior fitment and seal.
Motor mount service
p/n: 25-0063-11
Motor mount, upper, engine bracket at front cross member. One (1) per vehicle. Revulcanization service only.Length: 6.1875 inches. Width: 2.875 inches.
Motor mount service
p/n: 25-0073-11
Insulator, engine mount, front lower. Revulcanization service only.Length: 5.125 inches.
Trunk Weatherstrip
p/n: 50-0483-84
This trunk weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the trunk lid.
Trunk Weatherstrip Corners
p/n: 60-0511-85
These trunk weatherstrip corners are designed from the original part for superior fitment and seal. The seals mount to the front corners of the trunk directly to the body.
Hood To Cowl Weatherstrip
p/n: 70-0940-42
This Hood to Cowl Weatherstrip is designed from the original part for superior fitment and seal. An exact reproduction of the original profile. This seal mounts at the rear of the engine bay to seal between the hood and vehicle body cowl.
Door Auxiliary Weatherstrip
p/n: 60-0342-73
Weatherstrip, front door, auxiliary on door front at beltline, right and left. Held on by button fasteners (our #50-0198-73, four (4) each included in set). Also known as a "J" seal.
Stabilizer Bar End Link Set
p/n: 70-0567-34
Twenty-two (22) piece Stabilizer Bar End Link set for both sides of one (1) vehicle, fits front or rear bar. Order two (2) sets for vehicles with front and rear stabilizer bars. Hex head bolt. 5/16"-24NF x 7-5/8" long. Includes metal sleeves, cup washers and rubber grommets.
Front Spring Rubber Bumper
p/n: 70-0329-32
Front Spring Rubber Bumper - for upper control arm on frame.
Motor (Engine) Mount
p/n: 25-0060-11
Motor (engine) mount, lower front. One (1) per car. Length: 4.50 inches.
Rigid Run Channel
p/n: 70-0347-58
Stainless beaded edge, mohair-lined, exact replacement for rear side of division bar. Available in 15" pairs.
Flexible Run Channel
p/n: 70-1239-58
Cloth covered, mohair lined flexible metal channel for sides and top of door windows.
Beltline Weatherstrip
p/n: 70-0555-58
Weatherstrip, door window inner and outer, front and rear doors. Bend to fit. Available in a 3ft pair.
Vent division bar weatherstrip
p/n: 60-0534-56
Front vent window division post seal. Fully molded with metal core and attaching tabs.
Gearshift boot
p/n: 70-2126-24
Boot, transmission gear hand shift lever. Molded in pliable black rubber which may be painted if needed for restoration.
Front stabilizer bushing
p/n: 50-0094-34
Bushings, front stabilizer shaft-to-frame or stabilizer shaft, front or rear. Fully molded rubber. One and one half inch (1 1/2") length by one and one half inch (1 1/2") width by eleven sixteenths inch (11/16") inside hole diameter by one and one half in
Flexible Run Channel
p/n: 70-1238-58
Cloth covered, mohair lined flexible metal channel for sides and top of door windows.
Fenderskirt Edge Seal
p/n: 60-0109-45
Fenderskirt Edge Seal - One (1) ten (10) foot strip. Length: 120.0 inches.
Side Window Sash Channel
p/n: 70-0641-58
Sash channel, side window glass. U-shaped steel channel only, no filler. Will require that you attach your own window regulator cam to underside as required.
Rigid Run Channel
p/n: 70-0516-58
Channel, rigid run, lower side window below beltline, zinc plated steel with black cloth lining. Available in 15" pairs.
Door handle gasket kit
p/n: 70-2673-69
Gasket set, front or rear door handles. Machine die cut from long lasting thin stock rubber. Six (6) piece set for two (2) doors.
Brake & Clutch Pedal Pads
p/n: 25-0058-22
Pads, brake and clutch pedal. Two (2) per car. Length: 4.0 inches. Width: 2.5 inches.
Splash Apron / A-Arm Dust Shield
p/n: 70-3064-45
This two (2) piece Splash Apron / A-Arm Dust Shield Filler set is designed from the original part for superior fitment and seal. Filler pieces are die cut from quality masticated rubber to authentic original dimensions. Pieces fit over suspension a-arms and inside front inner fenders.
Body mounting pad
p/n: 27-0092-48
Insulator, body mounting pad. Metal core & locating collar covered with rubber. Two inch (2") square by fifteen sixteenths inch (15/16") locating collar outside diameter by five eighths inch (5/8") locating collar inside hole diameter. Seven sixteenths in
Hydraulic pump mounting pad
p/n: 70-0852-67
Pad, mounting, hydraulic pump. Used on models with hydraulic window lifts or hydraulic convertible top. Two (2) to three (3) required. per car.
Battery clamp cover
p/n: 70-0095-21
Cover, battery clamp. Control unsightly sulfate buildup. Help protect the nearby metal and finish. Good copy from original part.Length: 3.5 inches.
Rocker panel dust shield cover
p/n: 70-2392-45
Cover, rocker panel inner dust shield. Fully molded with proper attaching teeth and flap.
Window Stop Stem Bumper
p/n: 33-0675-62
Cushion (stem bumper), window stop, lower. For front and rear door, rear side and quarter windows as required.
Solenoid plunger boot
p/n: 60-0567-21
Boot, solenoid plunger, starter switch at starter.Height: 1.625 inches.
Hood bumper
p/n: 25-0068-42
Bumper, hood to fender, side.Length: 1.1875 inches. Width: .8125 inches.
Masticated rubber sheet
p/n: 70-0645-45
Masticated sheet. Three thirty seconds (3/32) inch thick rubber sheet containing random milled cotton cord reinforcement for front end splash aprons, etc. This product is a four (4) foot wide roll, and will only be sold in four (4) square foot multiples
Wiring grommet
p/n: 70-0355-14
Grommet, electric wire into light body under fenders, for headlights, taillights, some parking lights and auxiliary (fog) lights. Fits seven eighths (7/8) inch hole in light body. Two (2) to eight (8) per car as required.
Window Stop Stem Bumper
p/n: 33-0622-62
Bumper, window stop. One and one fourth (1-1/4) inch square by one half (1/2) inch thick. Compare with our #33-0540-62 and #33-0675-62.
Door bumper
p/n: 50-0203-41
Bumper, fuel filler door, rear fender. With steel core, screw retained two (2) per car.Width: .5 inches. Height: .625 inches.
Glovebox link bumper
p/n: 50-0367-88
Bumper, glove box check link. Fits on glove box door arm as needed.Length: .75 inches. Width: .5625 inches. Height: .3125 inches.
Window Stop Stem Bumper
p/n: 33-0540-62
Cushion (stem bumper), window stop, lower. For front and rear door, rear side and quarter windows as required.
Body Bolt Cushion
p/n: 60-0189-48
Pad, for each body bolt under frame bracket, to cushion washer and nut. Fully molded rubber. One and seven eighths inch (1 7/8") outside diameter by seven eighths inch (7/8") inside hole diameter by nine sixteenths inch (9/16) height.