Rear Shield to Bumper Seal
p/n: 30-0476-44
This Rear Shield to Bumper Seal is made of high quality EPDM dense rubber. The seal is designed from an original part so it fits correctly. Overall length is seven (7) feet.
Quarter Window Filler
p/n: 20-3085-62
Seal assembly. Installs on body below rear quarter glass to body weatherstrip.
Clutch and Brake Pedal Pads
p/n: 60-0068-22
This reproduction Clutch and Brake Pedal Pad pair slips over the full perimeter of the pedal for a precise, factory fit. An oval style perfect reproduction to replace worn or damaged original pedal pads.
Front Spring Rubber Bumpers
p/n: 70-0329-32
This Front Spring Rubber Bumper Pair fits to the upper control arms on frame. Manufactured to OEM specifications to install for an authentic fit, finish and function.
Front Door Auxiliary Weatherstrips
p/n: 70-0551-73
This Front Door Auxiliary Weatherstrip pair fits to the left and right doors at the beltline. Uses snap-in fasteners, four (4) each included.
Vent division bar weatherstrip
p/n: 70-1511-56
Front vent window division post seal. Fully molded with metal core and attaching tabs.
Rear Window Gasket Set
p/n: 60-0082-83
This Rear Window Gasket Set contains the rear window gasket itself and the locking strip. Both strips comes in a ninety inch (90") piece and mount around the full perimeter of the back glass. The ends may require trimming and bonding for installation.
Stabilizer Bar End Link Set
p/n: 70-0567-34
Twenty-two (22) piece Stabilizer Bar End Link set for both sides of one (1) vehicle, fits front or rear bar. Order two (2) sets for vehicles with front and rear stabilizer bars. Hex head bolt. 5/16"-24NF x 7-5/8" long. Includes metal sleeves, cup washers and rubber grommets.
Exhaust System Support Pad
p/n: 60-0319-13
This Exhaust System Support Pad is the right-angle type insulator and fabric reinforced. Molded with a steel core at one end as original style.
Quarter Window Filler
p/n: 70-3431-67
These quarter window fillers mount inside the rear panel at the bottom of the rear side window. The pair is fully molded as left and right with brass cores.
Front Stabilizer Bar Bushing
p/n: 70-1293-33
A Front Stabilizer Bar to Frame Bushing pair for both sides of the vehicle. Fits front stabilizer or sway bar. Manufactured with quality materials to original specifications. One (1) pair per vehicle.
Carpet Heel Plate
p/n: 70-3019-88
Heel pad for carpet. Seven and three eighths (7-3/8) inch wide by sixteen (16) inches long.
Front Suspension Rubber Bumper
p/n: 60-0103-32
Front Suspension Rubber Bumper for the front suspension lower control arm (attaches to lower arm spring mount). Steel core, with original size bolt. Width: 1.625 inches.
Division Bar Grommet
p/n: 70-0483-62
These Division Bar Grommets are fully molded for the rear door vent divider post (wind deflector). Four (4) piece set.
Vent division bar weatherstrip
p/n: 30-0532-56
Front vent window division post seal. Fully molded with metal core and attaching tabs.
Running Board To Body Filler
p/n: 70-1116-45
This Running Board To Body Filler is extruded from dense rubber for a durable and proper seal. Sold as a forty (40") inch pair of filler strips.
Rear Quarter Window Gasket Set
p/n: 60-0092-83
This rear corner quarter window gasket set contains the quarter window gaskets and locking strips. All of the strips in this four (4) piece set come in forty-five inch (45") pieces and mount around the perimeters of the quarter windows on five window trucks. The ends may require trimming and bonding for installation.
Hood to Cowl Weatherstrip
p/n: 70-0940-42
This Hood to Cowl Weatherstrip is designed from the original part for superior fitment and seal. An exact reproduction of the original profile. This seal mounts at the rear of the engine bay to seal between the hood and vehicle body cowl.
Flexible Run Channel
p/n: 60-0375-58
This flexible corrugated steel, cloth covered, and mohair lined channel is for windows with metal glass frames. Available in 5ft. lengths.
Vent Window Division Post Seals
p/n: 70-4333-56
This Front Vent Window Division Post Seal pair is designed from the original part for superior fitment and seal. Parts are fully molded EPDM rubber over a brass metal core.
Headlight seal
p/n: 70-2574-14
Seal, headlight to front fender retainer seal. Fully molded to fit like original, unlike a extruded strip that will buckle.
Axle Rebound Pad
p/n: 30-0534-32
Bumper, rear axle rebound.Length: 3.0 inches. Width: 2.375 inches. Height: 1.6875 inches.
U Jamb Lock Pillar Filler
p/n: 60-0570-79
This U Jamb Door Lock Pillar Filler pair is designed from the original part for superior fitment and sealing. This part seals the bottom of the rear side window. Fully molded authentic rubber construction with metal core.
Upper Control Arm Shaft
p/n: 20-1278-32
This three (3) piece Upper Control Arm Shaft set is designed from the original part for superior fitment and performance. Renew the performance of your aged and worn front suspension to restore the ride of your classic vintage vehicle.
Rear Window Gasket
p/n: 70-2051-81
This Rear Window Gasket is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the back glass and has vulcanized, or bonded, ends which means no cutting or splicing is required for installation.
Rear Vent Window Division Post Weatherstrip
p/n: 70-3762-56
This Rear Door Vent Window Division Post Weatherstrip pair is designed from the original part for superior fitment and seal. This seal is fully molded with EPDM rubber over brass metal cores. This part fits opposite the glass run channel and seals the vent window when the vent is closed.
Trunk Weatherstrip - Clipped
p/n: 70-1123-85
This Clipped Trunk Weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter and directly to the trunk lid using properly spaced plastic clips.
Windshield Gasket
p/n: 20-1321-50
This windshield gasket mounts around the full perimeter of the front glass and has properly molded corners for a precise, factory like fit. It also has the slot to accommodate the outer edge's decorative molding.
Fender Skirt Edge Weatherstrip
p/n: 70-0154-45
This Fender Skirt Edge Weatherstrip pair is designed from the original part for superior fitment, finish, and seal. This weatherstrips fits between the rear wheel fender skirt and the rear fender quarter panel.
Front Spring Bumpers
p/n: 60-0393-32
This Front Spring Bumper pair is a quality reproduction of the original factory part. These axle to frame bottoming rebound pads are dense rubber blocks that mount to the front axle.
Lower Tailgate Weatherstrip
p/n: 20-3142-85
This Lower Tailgate Weatherstrip is designed from the original part for superior fitment and seal. The weatherstrip mounts on the bottom of the tailgate.
Front Suspension Bumper
p/n: 70-1294-32
Bumper, front load rebound, upper.Width: 1.625 inches. Height: 2.75 inches.
Front Door Weatherstrips
p/n: 60-0299-72
This Front Door Weatherstrip pair is high-quality sponge rubber with inserted nylon clips. Designed from the original part for superior fitment and seal. Each strip is approximately one hundred sixty-six (166) inches long.
Fender Skirt Edge Weatherstrip
p/n: 25-0092-44
This Fender Skirt Edge Weatherstrip pair is designed from the original part for superior fitment, finish, and seal. This weatherstrips fits between the rear wheel fender skirt and the rear fender quarter panel.
Beltline Weatherstrip
p/n: 30-0301-57
Window felt inner and/or outer. Flexible, pile lined, rubber covered, with stainless bead. Available in 3ft pair.
Stabilizer Bushing
p/n: 70-0627-33
Bushings, stabilizer bar, front. Fully molded rubber. One and three fourths inch (1 3/4") length by one and one half inch (1 1/2") width by three fourths inch (3/4") inside hole diameter by one and five eighths inch (1 5/8") height.
Axle Rebound Pad
p/n: 70-1289-32
Bushing, rear support arm. Rear upper. Four (4) per car. For lower see #70-1290-32.
Axle Rebound Pad
p/n: 70-1290-32
Bushing, rear support arm. Rear lower. Four (4) per car. For upper see #70-1289-32.
Rear Axle Bumpers
p/n: 70-0210-32
This Rear Axle Bumper pair is a quality reproduction of the original factory part. These bottoming pads are dense rubber blocks that mount by bracket to the rear axle tube.
Axle Bumpers
p/n: 60-0491-32
This Rear Axle Bumper pair is a quality reproduction of the original factory part. These bottoming rebound pads are dense rubber blocks that mount to the rear axle tube.
U Jamb lock pillar filler
p/n: 50-0269-79
Door lock pillar seal. This part seals the bottom of the rear side window, and may also be known as a door jamb seal.