This is a six (6) piece door edge weatherstrip set. With three (3) parts for each door, this part is the primary door to body weatherstrip. Includes our part #20-3122-73.
This rear window gasket mounts around the full perimeter of the back glass and has properly molded corners for a precise, factory fit. It also has the slot to accommodate the outer edge's decorative molding.
This roof rail weatherstrip pair is made of high-quality EPDM rubber with vulcanized corners for a factory like fit. This part fits on the roof of the vehicle and seals the side window when the window is fully raised.
Seal, sunroof or glass top.
This Windshield Gasket is designed from the original part for superior fitment and seal. This gasket has a slot only on the bottom of the seal to accommodate the outer edge's decorative molding.
This three (3) piece Upper Control Arm Shaft set is designed from the original part for superior fitment and performance. Renew the performance of your aged and worn front suspension to restore the ride of your classic vintage vehicle.
Seals, top rear of door. Not included in door seal kits.
Seal assembly. Installs on body below rear quarter glass to body weatherstrip.
Channel, side window glass, vertical run. Flexible, felt lined, rubber covered channel. Available 60" lengths.
Channel, flexible door window run. Stainless steel beaded. Available in 5ft lengths.
Mount, front motor. Two (2) required per car.
Channel, front door sash. Right side.
Channel, front door sash. Left side.
This Beltline Weatherstrip installs on the left and right doors to wipe the inside and outside of the windows when the glass is lowered. Flexible, pile lined, rubber covered, with a black bead. Available in 3ft pair.
This Beltline Weatherstrip is sold as a three (3) foot pair. The beltline is used for side window inner and/or outer, front and/or rear doors. Available in a 3ft pair.
Pads, radiator splash shield. Four (4) required per vehicle.
This Side Window Weatherstrips can be used for inner and/or outer. The weatherstrip is flexible, pile lined, rubber covered, with black bead. Available in 3ft pairs.
Seals, front fender inner splash apron to suspension arm.
This Peel-N-Stick Trunk Weatherstrip is designed for superior fitment and seal. The seal mounts around the full perimeter of the trunk directly to the body. Easy to install 3M Peel-N-Stick backing provides superior adhesion for reliable performance.
This ten (10) piece Hood Bumper set is designed from the original parts for superior fitment and function.
This Clutch Rod to Firewall Boot is designed from the original part for superior fitment and seal. This boot makes a weathertight connection for the clutch rod lever as it passes through the firewall.
Seals, air vent damper. Must drill out spot welds to replace the cracked rubber. Includes screws to put back together.
This Trunk Weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the trunk lid.
Pads, taillight to body.
Support, transmission. Models with manual transmission only.
Bushing, brake master cylinder. Installs on push rod.
Seals, fender skirt.
Bumper, front suspension lower. Left side.
Bumper, front suspension lower. Right side.
Grommet, fuel filler neck. Fully molded rubber.
Pad, rear spring. Upper and lower. Four (4) required per car.
Gaskets, back-up light cover. Used on models without back-up lights.
Seal, steering tube to floor. Installs under floor mat.
Hinge Pillar Weatherstrip - Attaches to the body and seals between the A-pillar post and the front section of the door or vent window frame when the door is closed.
Seal, radiator air deflector to hood. Twenty two and one fourth (22-1/4) inches long. Two (2) piece set.
Rubber, garnish molding to dash. Eighty two (82) inches long.
Bushing, Rear Spring - Front #B5A-5781-C
Insulator, transmission gear shift column lever.
Seal, steering column tube. Installs on top of floor mat.
Bushing, control arm. Two (2) required per side.
This Splash Apron mounts between the front fender splash apron and the front fender. The seal is an exact reproduction of the original Ford part. Sold as a seventy-two (72) inch strip.
Bushings, stabilizer bar to frame. One (1) pair required per car.
Gaskets, ventilator air valve.1952-54: 1 pair required. 1955-56: 2 pair required.
Pad, rear mount antenna.
Gaskets, back-up light housing to body.
Bushing, control arm. Upper inner rear. One (1) required per side.
Bushing, control arm. Upper inner front. One (1) required per side.
Weatherstrip, door. Installs on inner dog leg. Included with door seal kits.