Front Door Weatherstrips
p/n: 60-0377-72
This Door Weatherstrip pair is designed from the original parts for superior fitment and seal to keep the elements out and reduce road noise while driving. Mount with pre-installed pins, to seal the driver and passenger doors when closed.
Front Door Weatherstrips
p/n: 60-0299-72
This Front Door Weatherstrip pair is high-quality sponge rubber with inserted nylon clips. Designed from the original part for superior fitment and seal. Each strip is approximately one hundred sixty-six (166) inches long.
Front Door Weatherstrips
p/n: 20-3113-72
This four (4) piece Front Door Weatherstrip set is designed from the original parts for superior fitment and seal. These door seals mount directly to the left and right front door pair to seal the full perimeter of the doors against the vehicle body when the door is closed.
Front Door Weatherstrips
p/n: 20-0525-72
This Front Door Weatherstrip pair is designed from the original part for superior fitment and seal. These primary door weatherstrips mount (glue-on) directly to the left and right front doors sealing the full perimeter of the doors against the vehicle body when the door is closed.
Front Door Weatherstrips
p/n: 60-0416-72
This Front Door Edge Weatherstrip pair is the primary door to body weatherstrip. This Original profile weatherstrip pair for 1955-2nd type pair is the OEM cross-section profile, proper length door edge seal which attaches to the door with pre-inserted plastic attaching pins.
Front Door Weatherstrips
p/n: 60-0485-72
This Front Door Edge Weatherstrip pair is the primary door to body weatherstrip. This smaller for 1955-2nd type weatherstrip pair is the proper length door edge seal which attaches to the door with pre-inserted plastic attaching pins.
Front Door Weatherstrips
p/n: 60-0248-72
This Front Door Weatherstrip pair provides superior fitment and seal to keep the elements out and reduce road noise. These door weatherstrips are the primary door to body seals for the driver and passenger doors when closed.
Front Engine Mount
p/n: 20-1786-11
This Front Engine Mount is made of a quality rubber over a metal core to provide maximum life and performance. Two (2) required per car.
Front fender center pad
p/n: 20-1865-45
Pads, back center of front fender. Mounts where fender bolts to cowl.
Front Fender Seal
p/n: 60-0438-45
Seal, vertical, front quarter panel (fender) to cab at rear of fender (cowl). Two (2) piece set for both sides of cab.
Front Header Bow Weatherstrip
p/n: 20-3097-64
This convertible top Front Header Bow Weatherstrip is designed from the original part for superior fitment and seal. This seal installs directly to the convertible top to seal between the soft top and the top of the windshield.
Front of Door Bumper
p/n: 70-2614-71
This Front of Door Bumper is a quality reproduction of the original factory part. This rubber door bumper attaches to support / cushion the door closure. Usually requires four (4) bumpers each per vehicle.
Front Spring Bumper
p/n: 30-0517-32
Bumper, front spring rebound, lower.Width: 2.125 inches. Height: 2.25 inches.
Front Spring Rubber Bumpers
p/n: 70-0329-32
This Front Spring Rubber Bumper Pair fits to the upper control arms on frame. Manufactured to OEM specifications to install for an authentic fit, finish and function.
Front Stabilizer Bar Bushing
p/n: 70-1293-33
A Front Stabilizer Bar to Frame Bushing pair for both sides of the vehicle. Fits front stabilizer or sway bar. Manufactured with quality materials to original specifications. One (1) pair per vehicle.
Front Stabilizer Bushing
p/n: 30-0298-33
Bushings, front stabilizer rod end. One (1) pair required per car. Fully molded rubber.
Front Stabilizer Bushing
p/n: 50-0094-34
Bushings, front stabilizer shaft-to-frame or stabilizer shaft, front or rear. Fully molded rubber.
Front Stabilizer Bushing
p/n: 60-0088-34
This Front Stabilizer Bushing pair is fully molded from EPDM dense rubber to ensure durability. Used to connect the stabilizer bar to the vehicle frame. Two (2) required per car.
Front Suspension Bumper
p/n: 27-0080-32
This Front Suspension Bumper, front suspension lower A-arm, is made from high-quality EPDM rubber for a precise, factory fit.
Front Suspension Bumper
p/n: 70-1295-32
Bumper assembly, front load compression, lower.Width: 2.125 inches. Height: 2.75 inches.
Front Suspension Bumper
p/n: 70-1294-32
Bumper, front load rebound, upper.Width: 1.625 inches. Height: 2.75 inches.
Front Suspension Bumpers
p/n: 40-0251-32
This Front Suspension Bumper pair for the upper arm is made from high-quality EPDM dense rubber for a precise, factory like fit. Two (2) required per car.
Front Suspension Rubber Bumper
p/n: 60-0103-32
Front Suspension Rubber Bumper for the front suspension lower control arm (attaches to lower arm spring mount). Steel core, with original size bolt. Width: 1.625 inches.
Front Upper Control Arm Bumpers
p/n: 60-0219-32
This front suspension Upper Control Arm Bumper pair is for the front suspension upper control arms. Self-retaining type rubber bumper.
Fuel Filler Neck Grommet
p/n: 20-0585-39
This Fuel Filler Neck Grommet is designed from the original part for superior fitment and seal. This grommet fits around the vehicles fuel filler neck between the filler neck and vehicle body.
Fuel Filler Neck Lower Cover Collar Seal
p/n: 70-3700-39
This Fuel Filler Neck Lower Cover seals the neck where it goes through rear fender splash panel on the trunk floor. Part is fully molded rubber with a corrosion resistant brass core.
Fuel Neck Grommet
p/n: 60-0475-41
Grommet, fuel filler neck (1955-2nd type). Fully molded rubber, slightly oblong. Three and one half inch (3-1/2") outside width by three and fifteen sixteenths inch (3-15/16") outside length.
Fuel Neck Grommet
p/n: 20-0581-39
Grommet, gas tank neck. Oval shaped. Fully molded rubber with retaining flange. Three and thirteen sixteenth inch (3-13/16") outside width by four and five sixteenths inch (4-5/16") outside length.
Fuel Tank Filler Neck Grommet
p/n: 20-1298-39
This Fuel Filler Neck Grommet is designed from the original part for superior fitment and seal. This fully molded flexible rubber grommet fits around the vehicles fuel filler neck between the filler neck and vehicle body.
Gas Filler Neck Seal Kit
p/n: 70-3763-39
This two (2) piece kit includes the gas tank filler neck upper and lower collar seals. These seals prevent gas fumes from entering the cabin. The upper seal fits on top of the fuel neck and seals against the back side of the fender behind the taillight. The collar seals the neck where it goes through rear fender splash panel on the trunk floor.
Gas Tank Filler Upper Seal
p/n: 70-3701-39
This Gas Tank Filler Upper Seal fits on top of the fuel neck and seals against the back side of the fender behind the taillight. A premium part fully molded with high quality EPDM rubber.
Gearshift Boot
p/n: 70-2285-26
Boot, transmission control shift lever. Fully molded out of black rubber instead of original white rubber, though it could be painted like original. For vehicles with Hydra-Matic column shift
Gearshift Boot
p/n: 70-2126-24
Boot, transmission gear hand shift lever. Molded in pliable black rubber which may be painted if needed for restoration.
Gearshift Bushing
p/n: 60-0237-24
This Gearshift Bushing is fully molded and designed from the original part for superior fitment and seal. This bushing is made from high-quality EPDM dense rubber to provide excellent durability. Designed for the gearshift shaft lever, large type.
Gearshift Knob
p/n: 20-0583-24
This black floor shift lever Gearshift Knob is designed from the original part for a superior fit and finish. This reproduction part is a direct screw on replacement for that broken, aged-out original knob.
Gearshift Knob
p/n: 20-0521-24
This black column shift lever Gearshift Knob is designed from the original part for a superior fit and finish. This sphere shaped reproduction part is a direct push on replacement for that broken, aged-out original knob.
Glass Weatherstrip Kit
p/n: 90-3045-90
This kit includes the weatherstrip components needed for the glass on your restoration project.
Glass Weatherstrip Kit
p/n: 90-3026-90
This Glass Weatherstrip Kit includes the weatherstrip components needed for the glass on your restoration project.
Glass Weatherstrip Kit
p/n: 90-3325-90
This seventeen (17) piece Glass Weatherstrip Kit includes the weatherstrip components needed for the glass on your classic restoration project. These parts are designed from originals for superior performance and a factory fit.
Glass Weatherstrip Kit
p/n: 90-3038-90
This kit includes the weatherstrip components needed for the glass on your restoration project.
Glass Weatherstrip Kit
p/n: 90-3025-90
This comprehensive twenty (20) piece glass kit includes the weatherstrip components needed for the glass on your restoration project. These parts are designed from originals for superior performance and a factory fit.
Glass Weatherstrip Kit
p/n: 90-3070-90
This kit includes the weatherstrip components needed for the glass on your restoration project.
Glass Weatherstrip Kit
p/n: 90-3081-90
This kit includes the weatherstrip components needed for the glass on your restoration project.
Glass Weatherstrip Kit
p/n: 90-3073-90
This twenty two (22) piece Glass Weatherstrip Kit includes the weatherstrip components needed for the glass on your restoration project. These parts are designed from originals for superior performance and factory fit.
Glass Weatherstrip Kit
p/n: 90-3068-90
This kit includes the weatherstrip components needed for the glass on your restoration project.
Glass Weatherstrip Kit
p/n: 90-3027-90
This Glass Weatherstrip Kit includes the weatherstrip components needed for the glass on your restoration project.
Glass Weatherstrip Kit
p/n: 90-3074-90
This kit includes the weatherstrip components needed for the glass on your restoration project.
Glass Weatherstrip Kit
p/n: 90-3029-90
This kit includes the weatherstrip components needed for the glass on your restoration project.
Glass Weatherstrip Kit
p/n: 90-3050-90
This Glass Weatherstrip Kit includes the weatherstrip components needed for the glass work on your restoration project.
Glass Weatherstrip Kit
p/n: 90-3022-90
This twenty (20) piece Glass Weatherstrip Kit includes the weatherstrip components needed for the glass on your restoration project.
Glass Weatherstrip Kit
p/n: 90-3071-90
This kit includes the weatherstrip components needed for the glass on your restoration project.
Glass Weatherstrip Kit
p/n: 90-3024-90
This kit includes the weatherstrip components needed for the glass on your restoration project.
Glass Weatherstrip Kit
p/n: 90-3048-90
This kit includes the weatherstrip components needed for the glass on your restoration project.
Glass Weatherstrip Kit
p/n: 90-3043-90
This kit includes the weatherstrip components needed for the glass on your restoration project.
Glass Weatherstrip Kit
p/n: 90-3075-90
This twenty (20) piece Glass Weatherstrip Kit includes the weatherstrip components needed for the glass on your restoration project. These parts are designed from originals for superior performance and factory fit.
Glass Weatherstrip Kit
p/n: 90-3028-90
This kit includes the weatherstrip components needed for the glass on your restoration project.
Glass Weatherstrip Kit
p/n: 90-3077-90
This kit includes the weatherstrip components needed for the glass on your restoration project.
Glovebox Arm Bumper Stop
p/n: 20-1399-88
Stop, glovebox arm.Ford Truck 1957-64 Stop, glovebox arm. Requires 2 each. Ford Cars 1955-68 Bumper, glovebox door check arm stop.
Glovebox Door Link Grommet
p/n: 70-0968-88
This Glovebox Door Link Grommet is designed from the original part for superior fitment and function. Grommet works to cushion the glovebox door closure.
Glovebox Link Bumper
p/n: 50-0367-88
This Glovebox Link Bumper is made to original specifications for an authentic fit and appearance. The glovebox check link bumper fits on the glovebox door arm.
Glovebox or Fuel Tank Filler Door Bumpers
p/n: 20-1220-88
This Glovebox or Fuel Tank Filler Door Bumper pair is a quality reproduction of the original factory part. This push on rubber bumper attaches to support / cushion the glovebox or filler door closure.
Gravel shield bumper
p/n: 20-2956-28
Pads, front stone deflector to bumper arm anti-rattler. One (1) required per car.
Hardtop Roof Rail Weatherstrip
p/n: 70-0842-73
Weatherstrip, hardtop roof rail filler or extension. Attaches to body. Made with metal core like original.
Hardtop Roof Rail Weatherstrips
p/n: 70-1008-68
This Hardtop Roof Rail Weatherstrip pair is made of ozone resistant EPDM sponge rubber with molded A pillar ends and metal cores for a factory like fit. These high-quality weatherstrips fit on the roof of the vehicle and work to seal the side windows when the window is fully raised.