Brake Master Cylinder Push Rod Boot
p/n: 60-0180-24
This Brake Master Cylinder Push Rod Boot is made from high-quality Nitrile rubber for a precise, factory like fit for your classic vehicle. Manufactured to OEM specifications to install for an authentic fit and finish.
Stabilizer Bar End Link Set
p/n: 60-0221-33
Twenty-two (22) piece Stabilizer Bar End Link set for both sides of one (1) vehicle, fits front or rear bar. Order two (2) sets for vehicles with front and rear stabilizer bars. Hex head bolt 3/8"-16 NF x 6-15/16" long. Comes with metal sleeve, metal cup washers and rubber grommets.
Windshield Post to Door Weatherstrips
p/n: 20-3093-63
This Windshield Post To Door Weatherstrip pair is designed from the original part for superior fitment and seal. These weatherstrips attache to the body and seal between the A-pillar post and the front section of the door or vent window frame when the door is closed.
Backup light gasket
p/n: 20-1246-17
Gaskets, back-up light cover. Used on models without back-up lights.
Firewall Grommet
p/n: 70-2066-24
This Firewall Grommet is used to run the emergency brake cable through the firewall. Designed from the original part for superior fit and seal.
Convertible Front Bow Weatherstrip
p/n: 60-0253-64
This Convertible Front Bow Weatherstrip is designed from the original part for superior fitment and seal. This header seal installs directly to the windshield frame to seal between the soft top and the rear center section.
Hood Bumper Set
p/n: 33-0681-42
This ten (10) piece Hood Bumper set is designed from the original parts for superior fitment and function.
Front Bow Weatherstrip
p/n: 60-0200-64
This convertible top Front Bow Weatherstrip is designed from the original part for superior fitment and seal. This seal installs directly to the convertible top between the folding soft top and the top of the outer windshield.
Vent Window Division Bar Weatherstrip
p/n: 70-1432-56
This Front Vent Window Division Bar Weatherstrip is designed from the original part for superior fitment and seal. A single 32" inch (approximate) length of original cross-section extruded rubber.
Body Mounting Pad
p/n: 50-0477-48
Pad, body mounting. Fully molded rubber with metal core & locating collar.
Header Bow Weatherstrip - Hardtop
p/n: 70-3918-64
This Header Bow Weatherstrip is the top and front seal rubber across windshield header for removable hardtops. Fully molded with the proper, as original, cross section in top quality rubber.
Body Mounting Pad
p/n: 70-1429-48
Pad, body mounting. Fully molded rubber with metal core and rubber locating collar. Also used for radiator cradle to frame. Eight (8) to ten (10) required per car. Two and one fourth inch (2 1/4") outside diameter by one and one sixteenth inch (1 1/16") l
1-7/16" Firewall Grommet
p/n: 60-0276-45
This Firewall Grommet is used to run the throttle rod and tube, oil pressure gauge pipe, heat indicator tube, and choke rod through the firewall.
Lower Rear Engine Mount
p/n: 20-0584-11
This Lower Rear Engine Mount is designed from original part for correct fitment and function. Made of a quality dense rubber for durability and proper engine vibration isolation. Two (2) required per truck.
Firewall Grommet
p/n: 70-2067-20
This Firewall Grommet is used to run the main wiring harness through the firewall. Designed from the original part for superior fit and seal.
Body Mount Isolator Pad
p/n: 70-0929-48
Body Mount Isolator Pad - Rubber with metal core and locating collar as original part. Part dimensions = Two and three sixteenths inch (2 3/16") square by one inch (1") overall height with thirteen sixteenths inch (13/16") inside bolt diameter. Does not include any fastener hardware.
Trunk Bumper
p/n: 70-0296-87
T-nut, trunk bumper in gutter at sides, brass core tapped 10-32 thread. Two (2) required per car. For models having partial weatherstrip in gutter of body.
Body Mounting Pad
p/n: 27-0092-48
Insulator, body mounting pad. Metal core & locating collar covered with rubber.
Parking Brake Pedal Pad
p/n: 25-0071-22
Pad, parking brake pedal.Length: 2.125 inches. Width: 2.0 inches.
Metal Sleeved Grommet
p/n: 70-0203-41
Flanged rubber grommet with metal sleeve bushing. Used as part of the accelerator relay lever. Also used from 1959-61 on all Cadillac models as a bushing for the windshield wiper relay lever adaptor.
Body Mounting Pad
p/n: 30-0500-48
Pad, body mounting. Fully molded rubber with locating collar and metal core. Number used varied according to body type.
Rear Leaf Spring Insulator
p/n: 70-0980-32
This Rear Leaf Spring Insulator is an exact replacement for the upper and lower spring pad. Two and one half (2-1/2) inches wide, with cloth reinforcement. Four (4) used per car.
Side Window Vertical Leading Edge
p/n: 20-3126-80
Side window vertical leading edge weatherstrip. Cut to length. NOT cloth covered. This part attaches to the vertical edge of the rear side windows when the rear side windows are fully raised. Designed from the original part for superior fitment and seal.
Fender Skirt Edge Weatherstrip
p/n: 20-3019-44
This Fender Skirt Edge Weatherstrip pair is designed from the original part for superior fitment, finish, and seal. This weatherstrips fits between the rear wheel fender skirt and the rear fender quarter panel.
Brake and Clutch Pedal Pad
p/n: 40-0287-22
Pads, brake and clutch pedal. Length: 3.625 inches. Width: 2.0 inches.
Brake and Clutch Pedal Pads
p/n: 70-3003-22
This reproduction Clutch and Brake Pedal Pad pair slips over the full perimeter of the brake pedal for a precise, factory fit. A square style direct fit reproduction to replace worn original pedal pads. Manufactured in black rubber.
Window Locking Strip - Black
p/n: 70-2195-52
This extruded Locking Strip is used to retain windshield gaskets in pickups and vans. Designed from the original part for superior fitment, finish and function. Available in 16ft lengths.
Fender Welting
p/n: 20-1591-44
This black Fender Welting is designed from the original part for superior fitment and seal. This welting material fits between the fenders and the vehicle body. Eight (8) foot length.
Roof emblem mounting pad
p/n: 70-2575-88
Pad, roof emblem mounting gasket. Machine die cut sponge rubber to exact required shape.
Spring Shackle Bushing Set
p/n: 20-1834-32
This Spring Shackle Bushing Set is for the rear of the rear leaf spring on car models and the front of the front leaf spring on truck models. Two (2) sets needed per vehicle.
Power brake carpet grommet
p/n: 70-3147-24
Grommet, carpet. Floor front carpet grommet use for power brake hole.
Body to Frame Mounting Pad
p/n: 60-0188-48
This Body to Frame Mounting Pad with locating collar functions as a body to frame isolator mounting pad. Molded from a top-quality EPDM rubber with a metal core, locating collar, and metal bolt. Two (2) required per vehicle.
Threaded Ends Insulator for Propeller Shaft and Exhaust Muffler
p/n: 70-0631-27
A steel core, double end threaded quality rubber Insulator that functions as an exhaust system muffler pipe bracket insulator. Also functions as a propeller shaft bearing to frame crossmember insulator.
Steering Column Tube To Floor Gasket
p/n: 20-1531-88
This Steering Column Tube To Floor Gasket is designed from the original part for superior fitment and sealing. This part fits around the steering column to seal the column tube through the body floor pan.
Cab Running Board Seal
p/n: 20-0519-45
This Cab Running Board Seal installs between the bottom of the cab and the running board. Sold as a pair for the left and right side.
Gearshift Boot
p/n: 70-2285-26
Boot, transmission control shift lever. Fully molded out of black rubber instead of original white rubber, though it could be painted like original. For vehicles with Hydra-Matic column shift
Firewall Seal
p/n: 70-1600-36
Grommet, power steering lines to frame.Length: 2.75 inches. Height: .75 inches.
Body Mounting Pad
p/n: 30-0501-48
Pad, body mounting. Fully molded rubber with metal core. Number used varied according to body type.
Headlight Outer Rim Seal
p/n: 27-0063-14
Headlight Outer Rim Seal - Used to seal the headlight beam retainer ring. Replaces # 5945844.
Brake and Clutch Pedal Pads
p/n: 25-0058-22
A pair of brake and clutch pedal pads. Two (2) per car. Length: 4 inches. Width: 2-1/2 inches.