Side Window Sash Channel
p/n: 70-0641-58
This Side Window Sash Channel is the u-shaped steel channel only, no filler. Sold in 4 foot strip, usually sufficient for two (2) windows.
Steering Column Floorplate
p/n: 60-0403-24
This Steering Column Floorplate is used as the steering gear and clutch pedal push rod dash seal. Fully molded with original style pattern. Does not have metal backing.
Front Door Hinge Pillar Weatherstrips
p/n: 70-0552-73
This Front Door Hinge Pillar Weatherstrip pair is designed from the original parts for superior fitment and seal. The pair attaches above the beltline, hinge pillar windshield post. These two (2) strips with pre-installed clips, one for each door, are manufactured for a factory like fit.
Rigid Run Channels
p/n: 70-0516-58
This Rigid Run Channel pair is zinc plated steel with black cloth inside lining to provide a smooth sliding surface for glass movement. Also works to protect the glass. Fastens in place by small screws or rivets on top and bottom.
Trunk Weatherstrip
p/n: 70-1122-85
This Trunk Weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the trunk lid. The seal glues directly to the trunk lid.
Body Bumper Kit
p/n: 90-0206-90
This ten (10) piece Body Bumper Kit is designed from the original part for superior fitment, finish and function. Designed from originals and made from top quality rubber to ensure durability.
5" Wide Bow Drill Cloth Tape
p/n: 70-1175-65
This Bow Drill Cloth Tape is used for covering convertible side window weatherstrip. Black in color and available in a five (5) foot roll.
Hood To Cowl Weatherstrip
p/n: 60-0153-42
This Hood To Cowl Weatherstrip is designed from the original part for superior fitment and seal. An exact copy reproduction of the original profile. This weatherstrip installs at the rear of the engine bay to seal between the hood and vehicle body cowl.
Taillight Gasket
p/n: 60-0691-15
This Taillight Gasket is made of fully molded soft-dense rubber compound to ensure proper installation and performance. Designed from the original part for the correct profile. Two (2) strips cut thirty-six (36) inches long.
Exhaust System Hanger
p/n: 60-0307-13
This Exhaust System Hanger is used for the muffler-to-tailpipe support (insulator) with reinforced webbing. Fully molded from top-quality EPDM dense rubber to ensure durability. One (1) required per car.
Brake Master Cylinder Push Rod Boot
p/n: 60-0180-24
This Brake Master Cylinder Push Rod Boot is made from high-quality Nitrile rubber for a precise, factory like fit for your classic vehicle. Manufactured to OEM specifications to install for an authentic fit and finish.
Front Bow Weatherstrip
p/n: 60-0200-64
This convertible top Front Bow Weatherstrip is designed from the original part for superior fitment and seal. This seal installs directly to the convertible top between the folding soft top and the top of the outer windshield.
Convertible Front Bow Weatherstrip
p/n: 60-0253-64
This Convertible Front Bow Weatherstrip is designed from the original part for superior fitment and seal. This header seal installs directly to the windshield frame to seal between the soft top and the rear center section.
Stabilizer Bar End Link Set
p/n: 60-0221-33
Twenty-two (22) piece Stabilizer Bar End Link set for both sides of one (1) vehicle, fits front or rear bar. Order two (2) sets for vehicles with front and rear stabilizer bars. Hex head bolt 3/8"-16 NF x 6-15/16" long. Comes with metal sleeve, metal cup washers and rubber grommets.
Quarter Window Vertical Leading Edge
p/n: 70-0141-58
This quarter to side window Vertical Leading Edge Weatherstrip pair is designed from the original part for superior fitment and seal. Slides into metal retaining channel attached to rear side window and seals between the front door window and the rear quarter window.
Battery Clamp Cover
p/n: 70-0095-21
This Battery Clamp Cover helps to protect the nearby metal and finish. Fully molded from high-quality EPDM rubber to ensure durability. Good copy from an original part.
2-1/2" Black Bow Drill Cloth Tape
p/n: 70-1172-65
This Bow Drill Cloth Tape is used for covering convertible side window weatherstrip. Black in color and available in a five (5) foot roll.
Cowl Drain Gutter Hose Grommet
p/n: 33-0329-54
This Cowl Drain Gutter Hose Grommet is fully molded and designed from the original part for superior fitment and seal. This grommet is made from high-quality EPDM dense rubber to provide excellent durability.
Solenoid Plunger Boot
p/n: 60-0567-21
Boot, solenoid plunger, starter switch at starter.Height: 1.625 inches.
Window Regulator | Accelerator Rod Seal
p/n: 60-0652-70
This Window Regular | Accelerator Rod Seal is used as a front window regulator seal for 1955-60 passenger cars with electric windows and for 1957-62 Corvette models. Used as an accelerator rod through toeboard seal for 1955-62 V8 only Corvettes.
2-1/2" Tan Bow Drill Cloth Tape
p/n: 70-1173-65
This Bow Drill Cloth Tape is used for covering convertible side window weatherstrip. Tan in color and available in a five (5) foot roll.
Exhaust Tailpipe Hanger Strap
p/n: 60-0308-13
This Exhaust Tailpipe Hanger Strap is made from high-quality rubber for a precise, factory like fit for your classic vehicle. Muffler/tailpipe system, reproduction strap type is manufactured to OEM specifications.
Hood To Fender Bumper
p/n: 60-0318-42
This Hood To Fender Bumper is a quality reproduction of the original factory part. This rubber bumper attaches to the front fender to support / cushion the hood closure. Usually requires four (4) bumpers each per vehicle, order as needed.
Splash Apron / A-Arm Dust Shield Set
p/n: 70-4041-45
This two (2) piece Splash Apron / A-Arm Dust Shield Set is designed from the original part for superior fitment and seal. Filler pieces are die cut from quality masticated rubber to authentic original dimensions.
Gearshift Bushing
p/n: 60-0237-24
This Gearshift Bushing is fully molded and designed from the original part for superior fitment and seal. This bushing is made from high-quality EPDM dense rubber to provide excellent durability. Designed for the gearshift shaft lever, large type.