Door edge weatherstrip. Includes both front and rear doors. This part is the primary door to body weatherstrip. Includes our part #20-3122-73.
This front door vent window weatherstrip kit is a four (4) piece set that contains the main vent window seals and division post seals. All of the pieces were designed from original parts for a precise, factory fit.
Pad kit, body to frame.
These front door vent window weatherstrips are the main seals needed to replace the rubber on your vent windows. They are designed and molded from original parts for superior fitment and seal.
This rear window gasket mounts around the full perimeter of the back glass and has properly molded corners for a precise, factory fit. It also has the slot to accommodate the outer edge's decorative molding.
Rear door stationary vent seal
Original equipment style side window horizontal seal kit (also known as beltline weatherstrip). Eight (8) piece kit includes inner and outer felt beltline weatherstrip for each door and quarter windows.
Door edge weatherstrip. This part is the primary door to body weatherstrip. Includes our part #20-3122-73.
This windshield gasket is designed from the original part for superior fitment and seal. This gasket has a slot completely all around the seal to accommodate the outer edge's decorative molding.
Channel, side window glass, vertical run. Flexible, felt lined, rubber covered channel. Available 60" lengths.
Channel, flexible door window run. Stainless steel beaded. Available in 5ft lengths.
Mount, front motor. Two (2) required per car.
Channel, front door sash. Right side.
Channel, front door sash. Left side.
Window felt inner and/or outer. Flexible, pile lined, rubber covered, with black bead. Available in 3ft pair.
Weatherstrip, door window inner and outer, front and rear doors. Bend to fit. Available in a 3ft pair.
This trunk weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the trunk directly to the body. Easy to install 3M Peel-N-Stick backing provides superior adhesion for reliable performance.
Pads, radiator splash shield. Four (4) required per vehicle.
Window felt inner and/or outer. Flexible, pile lined, rubber covered, with black bead. Available in 3ft pairs.
Seals, front fender inner splash apron to suspension arm.
Channel, front door division bar.Length: 30.0 inches.
Bumper kit, hood. Ten (10) piece set.
Front vent window division post seal. Fully molded with metal core and attaching tabs.
This trunk weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the trunk lid.
This Clutch Rod to Firewall Boot is designed from the original part for superior fitment and seal. This boot makes a weathertight connection for the clutch rod lever as it passes through the firewall.
Seals, air vent damper. Must drill out spot welds to replace the cracked rubber. Includes screws to put back together.
Pads, taillight to body.
Bumpers, upper door glass. Installs on backside top of vent window frame where window rolls up against it.
Support, transmission. Models with manual transmission only.
Bushing, brake master cylinder. Installs on push rod.
Seals, fender skirt.
Bumper, front suspension lower. Left side.
Bumper, front suspension lower. Right side.
Grommet, fuel filler neck. Fully molded rubber.
Pad, rear spring. Upper and lower. Four (4) required per car.
Gaskets, back-up light cover. Used on models without back-up lights.
Seal, steering tube to floor. Installs under floor mat.
Seal, radiator air deflector to hood. Twenty two and one fourth (22-1/4) inches long. Two (2) piece set.
Bushing, Rear Spring - Front #B5A-5781-C
Insulator, transmission gear shift column lever.
Seal, steering column tube. Installs on top of floor mat.
Bushing, control arm. Two (2) required per side.
Seal, front fender splash apron to fender anti-squeak. Seventy two (72) inch strip.
Bushings, stabilizer bar to frame. One (1) pair required per car.
Gaskets, ventilator air valve.1952-54: 1 pair required. 1955-56: 2 pair required.
Pad, rear mount antenna.
Bushing, control arm. Upper inner front. One (1) required per side.
Bushing, control arm. Upper inner rear. One (1) required per side.