Search Results
Please click on the part name in red in order to get a complete description.
Front Door weatherstrip
p/n: 90-0126-72
Weatherstrip, front door kit. Includes weatherstrip for door perimeter, upper and lower hinge pillar.
Side roof rail weatherstrip
p/n: 30-0377-65
Weatherstrip, roof rail set, fits into metal retainer channels. Six (6) piece set for right and left side. For windshield stanchion pieces see our #30-0431-65 (1951-54) or our #30-0417-73 (1955-56).
Vibration damper service
p/n: 30-0520-12
Vibration damper, crankshaft, front. Revulcanizing service only. NOTE: This service does not include rebalancing.
Windshield Gasket
p/n: 30-0270-50
This windshield gasket mounts around the full perimeter of the front glass and has properly molded corners for a precise, factory fit. It also has the slot to accommodate the outer edge's decorative molding.
Front Door Vent Window Kit
p/n: 90-0332-90
This front door vent window weatherstrip kit is a four (4) piece set that contains the main vent window seals and division post seals. All of the pieces were designed from original parts for a precise, factory fit.
Front Door Vent Window Weatherstrips
p/n: 30-0531-55
These front door vent window weatherstrips are the main seals needed to replace the rubber on your vent windows. They are designed and molded from original parts for superior fitment and seal.
Motor mount service
p/n: 30-0378-11
Insulator assembly, engine support, front. Revulcanizing service only.
Door weatherstrip
p/n: 30-0326-73
Weatherstrip, front doors, right and left, on hinge pillar below beltline. This is a vertical weatherstrip mounted on the body.Length: 33.25 inches.
Motor mount service
p/n: 30-0424-11
Mount, engine support, rear. Revulcanization service only. For all models with UltraMatic transmission.
Taillight gasket kit
p/n: 70-1513-15
Gasket set, taillight housing and lens. Ten (10) piece set includes all lens and light body gaskets for both sides.
Accelerator pedal service
p/n: 70-3144-41
Pad, accelerator pedal. Revulcanization service only. Includes new ball sockets as original, with correctly detailed tread pattern.
Front suspension bumper
p/n: 70-1295-32
Bumper assembly, front load compression, lower.Width: 2.125 inches. Height: 2.75 inches.
Side window leading edge
p/n: 30-0388-57
Weatherstrip, rear quarter window leading edge against door glass frame, right and left.Length: 13.50 inches. Width: .8125 inches.
Door weatherstrip
p/n: 30-0468-73
Weatherstrip, door hinge pillar. Molded rubber ends attached to sponge rubber extrusion replacement.Length: 36.0 inches.
Trunk Weatherstrip
p/n: 70-1691-84
This trunk weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the trunk directly to the body.
Rigid run channel
p/n: 30-0180-57
Channel, rigid run, for vent window division bar. Chrome beaded edge, mohair lined steel channel to proper dimensions for window side of wing window frame.
Door weatherstrip
p/n: 30-0327-73
Weatherstrip, front door, right and left, lock side on door upper corner. Designed to attach to our #70-0219-73 weatherstrip.Length: 3.25 inches.
Steering column grommet
p/n: 70-1895-36
Grommet, steering column at dash. See #70-1894-36 for grommet at floorboard.Width: 2.625 inches.
Division bar bumper
p/n: 70-1443-62
Bumper, upper division post. Molded rubber part with a brass core.
Beltline weatherstrip
p/n: 30-0301-57
Window felt inner and/or outer. One (1) pair of three (3) foot lengths. Flexible, pile lined, rubber covered, with stainless bead. For front door, rear door and quarter windows. Replaces factory #466638, 466639
Front suspension bumper
p/n: 70-1294-32
Bumper, front load rebound, upper.Width: 1.625 inches. Height: 2.75 inches.
Axle rebound pad
p/n: 30-0534-32
Bumper, rear axle rebound.Length: 3.0 inches. Width: 2.375 inches. Height: 1.6875 inches.
Vent division bar weatherstrip
p/n: 30-0532-56
Front vent window division post seal. Fully molded with metal core and attaching tabs.
Front stabilizer bushing
p/n: 70-1293-33
Bushing, front stabilizer rod. One (1) pair per vehicleLength: 1.5625 inches. Width: 1.75 inches. Height: 1.625 inches.
Carpet heel plate
p/n: 70-3019-88
Heel pad for carpet. Seven and three eighths (7-3/8) inch wide by sixteen (16) inches long.
Beltline weatherstrip
p/n: 30-0300-58
Window felt inner and/or outer. One (1) pair of three (3) foot lengths. Flexible, pile lined, rubber covered, with stainless bead. For front door, rear door and quarter windows. Replaces factory #466634, 466635.
Coil wire sleeve
p/n: 70-2052-21
Boot, spark plug wire, at spark plug. All original textures and details.Length: 2.0 inches.
Front stabilizer bushing
p/n: 30-0298-33
Bushings, front stabilizer rod end. One (1) pair required per car. Fully molded rubber. One and one half inch (1 1/2") length by one and one eighth inch (1 1/8") width by three fourths inch (3/4") inside hole diameter by one and one half inch (1 1/2") hei
Windshield weatherstrip
p/n: 70-1535-52
Weatherstrip, windshield garnish molding on lower windshield post. Molded rubber replacement for #469222-3.
Hood to cowl weatherstrip
p/n: 30-0527-42
Weatherstrip, hood to cowl. Overall thirty seven (37) inches long.
Firewall grommet
p/n: 30-0456-20
Grommet, heater core at firewall.Length: 3.5625 inches. Width: 2.25 inches.
Parking light gasket
p/n: 70-2023-15
Gasket, parking light housing. Die cut from durable black sponge-cell rubber. One (1) pair needed per car.Length: 11.375 inches.
Antenna mount pad
p/n: 70-2264-21
Pad, antenna mount. For rear mounted twin antennas. See our #32-0390-21 for insulating grommet.
Power window switch bezel pad
p/n: 70-2137-21
Mounting pad, power window die cast bezel. Used under 4 way switch, typically found on drivers door.Width: 2.0 inches.
Bowdrill cloth tape
p/n: 70-1175-65
Tape, black bowdrill cloth. Adhesive backed, used to create cloth cover surface for side rail weatherstrips typically. Five (5) inches by five (5) foot roll. Pressure sensitive, for covering convertible side window weatherstrip such as our #70-1170-99 or
Firewall seal
p/n: 70-1599-36
Grommet, power steering lines to air duct.Length: 3.3125 inches. Width: .75 inches.
Power window switch bezel pad
p/n: 70-2136-21
Mounting pad, power window die cast bezel. Used under single window switch, typically found on front passenger door and rear windows.
Firewall seal
p/n: 70-1600-36
Grommet, power steering lines to frame.Length: 2.75 inches. Height: .75 inches.
Power brake carpet grommet
p/n: 70-3147-24
Grommet, carpet. Floor front carpet grommet use for power brake hole.
Body mounting pad
p/n: 70-1429-48
Pad, body mounting. Fully molded rubber with metal core and rubber locating collar. Also used for radiator cradle to frame. Eight (8) to ten (10) required per car. Two and one fourth inch (2 1/4") outside diameter by one and one sixteenth inch (1 1/16") l
Battery clamp cover
p/n: 70-0095-21
Cover, battery clamp. Control unsightly sulfate buildup. Help protect the nearby metal and finish. Good copy from original part.Length: 3.5 inches.
Accelerator hinge grommet
p/n: 30-0539-41
Grommet, accelerator pedal hinge to floorboard.Length: 3.50 inches. Width: 2.50 inches.
Hood bumper
p/n: 30-0304-42
Bumper, hood, on side of fender. Six (6) required per car.Length: 1.0 inches. Width: 1.375 inches.
Bowdrill cloth tape
p/n: 70-1172-65
Tape, black bowdrill cloth. Adhesive backed, used to create cloth cover surface for side rail weatherstrips typically. Two and one half (2-1/2) inches by five (5) foot roll. Pressure sensitive, for covering convertible side window weatherstrip such as our
Tan bowdrill cloth tape
p/n: 70-1173-65
Tape, brown (tan) bowdrill cloth. Adhesive backed, used to create cloth cover surface for side rail weatherstrips typically. Two and one half (2-1/2) inches by five (5) foot roll. Pressure sensitive, for covering convertible side window weatherstrip such
Heater core tube grommet
p/n: 30-0421-31
Grommet, heater inlet and outlet hose. Soft pliable rubber.
Power steering bushing
p/n: 70-1968-36
Bushing, power steering cylinder to frame. Two (2) required per car.Height: .625 inches.
Masticated rubber sheet
p/n: 70-0645-45
Masticated sheet. Three thirty seconds (3/32) inch thick rubber sheet containing random milled cotton cord reinforcement for front end splash aprons, etc. This product is a four (4) foot wide roll, and will only be sold in four (4) square foot multiples
Body mounting pad
p/n: 70-1430-48
Pad, body mounting. Fully molded rubber. Also used for radiator cradle to frame. Eight (8) to ten (10) required per car. Two and one eighth inch (2 1/8") outside diameter by three fourths inch (3/4") inside hole diameter by five sixteenths inch (5/16") he
Overdrive linkage grommet
p/n: 70-2031-24
Grommet, overdrive control linkage. Spool type grommet used on manual transmission models with factory overdrive. Three fourths inch (3/4") outside diameter by three eighths inch (3/8") inside hole diameter by three eighths inch (3/8") height.
Peel-N-Stick Trunk Weatherstrip
p/n: 30-0356-WT
This trunk weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the trunk directly to the body. Easy to install 3M Peel-N-Stick backing provides superior adhesion for reliable performance.
Run channel mohair liner
p/n: 70-2863-58
Liner, mohair. Liner with a rubber backing. Apply with adhesive to division bars and channels. Helps reline guide bars on lock side of hardtops and convertibles.
Door Weatherstrip
p/n: 70-0491-73
Weatherstrip, door edge. Fine grain sponge. Larger type used on most GM cars this period. Width: 13/16". Height: 11/16".
Trunk Weatherstrip (Sponge Rubber Extrusion - General Use)
p/n: 30-0356-85
Trunk weatherstrip made from high quality EPDM sponge rubber. Excellent for use on many different vehicle models.
Universal mounting pad
p/n: 70-0308-17
Mounting pad, continuous for lights, hinges, brackets, and other bright work when no molded pad is available.
Door weatherstrip
p/n: 70-0219-73
Weatherstrip, door edge, constant section on some models. Five eighths (5/8) inch by (5/8) inch cross-section, high grade, fine grain sponge rubber.
Sash channel filler 1/16 cork
p/n: 70-1115-57
Filler strip, window glass sash channel. One sixteenths (1/16) inch thick by 1-1/2 inches wide. For all applications fitting glass to sash channel not requiring weatherstrip type of filler. This is the highest quality linen back, rubber cork composition on
Antenna grommet
p/n: 32-0390-21
Grommet, insulator. For rear mounted twin antennas. Sheet Metal Hole: 1" Center Hole: 3/4" Outside Diameter: 1-1/4" Slot Width: 1/16"
Sash Channel Filler 1/16 Rubber
p/n: 70-2170-57
Filler strip, window glass sash channel. One sixteenths (1/16) inch thick by 1-1/2 inches wide. For all applications fitting glass to sash channel not requiring weatherlip type of filler. This is the highest quality rubber like polymer designed for settin
Sash channel filler 1/32 cork
p/n: 70-1114-57
Filler strip, window glass sash channel. One thirty seconds (1/32) inch thick by 1-1/2 inches wide. For all applications fitting glass to sash channel not requiring weatherlip type of filler. This is the highest quality linen back, rubber cork composition
Sash Channel Filler 1/32 Rubber
p/n: 70-2169-57
Filler strip, window glass sash channel. One thirty seconds (1/32) inch thick by 1-1/2 inches wide. For all applications fitting glass to sash channel not requiring weatherlip type of filler.
Shock absorber bushing
p/n: 70-0547-32
Bushing, shock absorber mounting. Double cone style, rear. Five eighths (5/8) inch hole, one and one sixteenths (1-3/16) inch outside diameter, three fourth (3/4) inch thick.