Search Results

70 items found matching 1956 Pontiac Chieftain 4 door Wagon - 2 seat
The listing below contains just short, abbreviated descriptions.
Please click on the part name in red in order to get a complete description.
Glass Weatherstrip Kit

p/n: 90-3028-90

This kit includes the weatherstrip components needed for the glass on your restoration project.

$865.90/set
$779.30/set
10% discount
Kit
Body Weatherstrip Kit

p/n: 90-3017-90

This kit includes the major weatherstrip components and some other essential parts needed for the body of your restoration project.

$391.70/set
$352.50/set
10% discount
Kit
Side window run channel kit

p/n: 90-0141-58

This ten (10) piece kit includes the inner and outer windowfelts, upper and lower rigid run channels, and flexible run channels needed to complete two (2) doors. Used for front or rear doors in models with vent windows in the door.

$272.20/set
$245.00/set
10% discount
Kit
Front Door Vent Window Kit

p/n: 90-0402-90

This front door vent window weatherstrip kit is a four (4) piece set that contains the main vent window seals and division post seals. All of the pieces were designed from original parts for a precise, factory fit.

$139.60/set
$132.60/set
5% discount
Kit
Door weatherstrip

p/n: 60-0247-72

Door edge weatherstrip, with pins. This part is the primary door to body weatherstrip. For Cadillac models, these are for the FRONT doors ONLY. For Chevrolet and Pontiac models, these are for the REAR doors ONLY.

$128.60/pr.
In Stock
Motor mount service

p/n: 27-0044-11

Insulator, engine support rear, right and left. For models with a manual transmission. Revulcanization service only.

$127.80/pr.
Call or Email
Front Door weatherstrip

p/n: 60-0299-72

Door weatherstrip, front door snap-on type. High quality sponge rubber with inserted nylon clips. Each strip approximately one hundred sixty six (166) inches long. Note: For 4 door vehicles see our part #60-0247-72 for the rear door.

$122.60/pr.
In Stock
Windshield Gasket

p/n: 60-0266-50

This windshield gasket is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the front glass and has vulcanized, or bonded, ends which means no cutting or splicing is required for installation. It also has the slot to accommodate the outer edge's decorative molding.

$117.30/ea.
In Stock
Motor mount service

p/n: 25-0063-11

Motor mount, upper, engine bracket at front cross member. One (1) per vehicle. Revulcanization service only.Length: 6.1875 inches. Width: 2.875 inches.

$95.80/ea.
Call or Email
Front Door Vent Window Weatherstrips

p/n: 38-0060-55

These front door vent window weatherstrips are the main seals needed to replace the rubber on your vent windows. They are designed and molded from original parts for superior fitment and seal.

$93.50/pr.
In Stock
Front suspension bumper

p/n: 27-0080-32

Bumper, front suspension lower A-arm.

$91.60/pr.
In Stock
Rigid run channel

p/n: 70-0536-58

Run channel, front door window, for full length of division bar (approximately twenty nine (29) inches). Rigid, bright beaded edge, mohair lined channel, die trimmed and formed at top.

$85.50/pr.
In Stock
Axle rebound pad

p/n: 27-0081-32

Bumper, rear axle on leaf spring.Width: 3.25 inches. Height: 4.75 inches.

$81.60/pr.
Made to Order Takes 1-2 Days
Rear Window Gasket

p/n: 70-2051-81

This rear window gasket is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the back glass and has vulcanized, or bonded, ends which means no cutting or splicing is required for installation.

$64.60/ea.
In Stock
Door Auxiliary Weatherstrip

p/n: 60-0342-73

Weatherstrip, front door, auxiliary on door front at beltline, right and left. Held on by button fasteners (our #50-0198-73, four (4) each included in set). Also known as a "J" seal.

$60.40/set
In Stock
Tailgate or Back Door Weatherstrip

p/n: 70-3604-84

This tailgate or back door weatherstrip is designed from the original part for superior fitment and seal. The seal mounts with properly spaced plastic clips around the full perimeter of the rear opening.

$56.10/ea.
In Stock
Stabilizer bushing

p/n: 27-0085-34

Bushings, for stabilizer bracket. Fully molded rubber. Correct dimensions, not an aftermarket replacement. One and three fourths inch (1 3/4') length by one and three eighths inch (1 3/8") width by three fourths inch (3/4") inside hole diameter by one and

$52.70/pr.
In Stock
Motor (Engine) Mount

p/n: 25-0060-11

Motor (engine) mount, lower front. One (1) per car. Length: 4.50 inches.

$52.10/ea.
In Stock
Rigid Run Channel

p/n: 70-0347-58

Channel, rigid run, window division bar. Stainless beaded edge, mohair-lined, exact replacement for rear side of division bar.

$52.10/pr.
In Stock
Flexible Run Channel 6 Foot

p/n: 70-1239-58

Window run channel with stainless beaded edge. Six (6) foot length. Cloth covered, mohair lined, flexible channel for sides and top of door windows. Exact replacement for listed vehicles but can be used in many applications.

$48.20/ea.
In Stock
Beltline weatherstrip

p/n: 70-0555-58

Weatherstrip, door window inner and outer, front and rear doors. Seven sixteenths (7/16) inch wide, with chrome bead, mohair faced, flexible. Two (2) three (3) foot strips. Bend to fit.

$47.70/pr.
In Stock
Axle rebound pad

p/n: 27-0089-32

Bumper, rear axle.

$46.50/pr.
Made to Order Takes 2-3 Days
Vent division bar weatherstrip

p/n: 60-0529-56

Front vent window division post seal. Fully molded with metal core and attaching tabs.

$46.10/pr.
In Stock
Flexible Run Channel 5 Foot

p/n: 70-1238-58

Window run channel, stainless beaded edge. Cloth covered, mohair lined flexible metal channel for sides and top of door windows. Perfect dimensions, Five eighths (5/8) inch wide by nine sixteenths (9/16) inch overall height, exact replacement. Five (5) fo

$44.30/ea.
In Stock
Headlight Mounting Pad

p/n: 70-0201-14

Headlight body mounting gasket. Rubber.

$41.10/pr.
In Stock
Fenderskirt edge seal

p/n: 60-0201-45

Seal, fenderskirt edge. Proper profile for most skirts of this period, including Fox-Craft. Sixty (60) inch strip.Length: 60. inches. Width: .75 inches.

$40.00/pr.
In Stock
Steel sash channel

p/n: 70-0641-58

Sash channel, side window glass. U-shaped steel channel only, no filler. Will require that you attach your own window regulator cam to underside as required.

$39.10/ea.
In Stock
Rigid run channel

p/n: 70-0516-58

Channel, rigid run, lower side window below beltline, zinc plated steel with black cloth lining, one half (1/2) inch deep by one half (1/2) inch wide, fifteen (15) inches long.

$36.10/pr.
In Stock
Headlight Outer Rim Seal

p/n: 27-0063-14

Headlight Outer Rim Seal - Used to seal the headlight beam retainer ring. Replaces # 5945844.

$26.50/pr.
In Stock
Hood to cowl weatherstrip

p/n: 60-0153-42

Weatherstrip, hood to cowl. Exact copy with clips.

$24.00/ea.
In Stock
Body mounting pad

p/n: 27-0092-48

Insulator, body mounting pad. Metal core & locating collar covered with rubber. Two inch (2") square by fifteen sixteenths inch (15/16") locating collar outside diameter by five eighths inch (5/8") locating collar inside hole diameter. Seven sixteenths in

$21.80/ea.
In Stock
Battery clamp cover

p/n: 70-0095-21

Cover, battery clamp. Control unsightly sulfate buildup. Help protect the nearby metal and finish. Good copy from original part.Length: 3.5 inches.

$18.80/ea.
In Stock
Rocker panel dust shield cover

p/n: 70-2392-45

Cover, rocker panel inner dust shield. Fully molded with proper attaching teeth and flap.

$18.30/pr.
In Stock
Window stop stem bumper

p/n: 33-0675-62

Cushion (stem bumper), window stop, lower. For front and rear door, rear side and quarter windows as required. (See sketch and our #33-0540-62).

$15.10/pr.
In Stock
Hood bumper

p/n: 27-0056-42

Bumper, hood side to fender ledge. Not all models used the same number of these, so check your car to see how many you need.Width: 1.0 inches.

$13.30/ea.
In Stock
Dimmer switch grommet

p/n: 40-0083-88

Grommet, dimmer switch for carpet application.

$11.00/ea.
In Stock
Masticated rubber sheet

p/n: 70-0645-45

Masticated sheet. Three thirty seconds (3/32) inch thick rubber sheet containing random milled cotton cord reinforcement for front end splash aprons, etc. This product is a four (4) foot wide roll, and will only be sold in four (4) square foot multiples

$10.80/sqf
In Stock
Wiring grommet

p/n: 70-0355-14

Grommet, electric wire into light body under fenders, for headlights, taillights, some parking lights and auxiliary (fog) lights. Fits seven eighths (7/8) inch hole in light body. Two (2) to eight (8) per car as required.

$10.60/ea.
In Stock
Window stop stem bumper

p/n: 33-0622-62

Bumper, window stop. One and one fourth (1-1/4) inch square by one half (1/2) inch thick. Compare with our #33-0540-62 and #33-0675-62.Length: 1.

$9.50/ea.
In Stock
Glovebox link bumper

p/n: 50-0367-88

Bumper, glove box check link. Fits on glove box door arm as needed.Length: .75 inches. Width: .5625 inches. Height: .3125 inches.

$7.90/ea.
In Stock
Window stop stem bumper

p/n: 33-0540-62

Cushion (stem bumper), window stop, lower. For front and rear door, rear side and quarter windows as required.

$7.90/ea.
In Stock
Tie rod dust cover

p/n: 70-0537-32

Dust cover, tie rod ends.

$7.80/ea.
In Stock
Body Bolt Cushion

p/n: 60-0189-48

Pad, for each body bolt under frame bracket, to cushion washer and nut. Fully molded rubber. One and seven eighths inch (1 7/8") outside diameter by seven eighths inch (7/8") inside hole diameter by nine sixteenths inch (9/16) height.

$7.60/ea.
In Stock
Door Weatherstrip w/ Clips (Sponge Rubber Extrusion - General Use)

p/n: 70-1112-73

Door edge weatherstrip made from high quality EPDM sponge rubber. Excellent for use on many different vehicle models.

$7.40/ft.
In Stock
Side window roller

p/n: 70-0117-62

Anti-rattle roller, side windows. Rubber only, replaces original perfectly and easily. Fits both styles of brackets.

$7.30/ea.
In Stock
Taillight Gasket

p/n: 60-0671-15

Gasket, taillight to fender. Two 1/4" strips of sponge rubber cut 26-3/4" long. One (1) pair required per car.

$7.20/pr.
In Stock
Brown door lock knob

p/n: 70-0660-70

Knob or push button for inside door lock, fits over 1/8" steel rod to door lock. Hard brown rubber, may be lacquered other colors as required.

$7.00/ea.
In Stock
Brown door lock knob

p/n: 70-0354-70

Knob for inside door lock control rod. Neutral brown color rubber, 3/32 inch hole. See also our #70-0660-70.

$6.30/ea.
In Stock
Shock and stabilizer grommet

p/n: 70-0274-33

Grommet, shock and stabilizer link. Eight (8) required per car. Fully molded rubber with locating collar. One and one sixteenth inch (1 1/16") outside diameter by nine sixteenths inch (9/16") locating collar outside diameter by three eighths inch (3/8") i

$6.30/ea.
In Stock
Universal mounting pad

p/n: 70-0308-17

Mounting pad, continuous for lights, hinges, brackets, and other bright work when no molded pad is available.

$5.80/ft.
In Stock
Door drain hole seal

p/n: 60-0442-70

Weatherstrip, door bottom drain hole seal. Also used on tailgate of station wagon. (Two (2) required for this use).Length: 4.0 inches.

$5.60/ea.
In Stock
Door Weatherstrip w/o Clips (Sponge Rubber Extrusion - General Use)

p/n: 70-1111-73

Door edge weatherstrip made from high quality EPDM sponge rubber. Excellent for use on many different vehicle models.

$5.50/ft.
In Stock
Door weatherstrip

p/n: 70-0219-73

Weatherstrip, door edge, constant section on some models. Five eighths (5/8) inch by (5/8) inch cross-section, high grade, fine grain sponge rubber.

$5.30/ft.
In Stock
Firewall grommet

p/n: 35-0515-20

Grommet, floor pan, rear compartment and body.

$4.70/ea.
In Stock
Sash channel filler 1/16 cork

p/n: 70-1115-57

Filler strip, window glass sash channel. One sixteenths (1/16) inch thick by 1-1/2 inches wide. For all applications fitting glass to sash channel not requiring weatherstrip type of filler. This is the highest quality linen back, rubber cork composition on

$4.69/ft.
In Stock
Firewall retainer

p/n: 60-0586-20

Retainer, firewall insulation panel. "Christmas Tree" style popular during this time. Constructed of vinyl plastic. Up to ten (10) required per car.

$4.60/ea.
In Stock
Door lock bumper

p/n: 34-0484-71

Bumper, door lock post, upper, one half (1/2) inch diameter by one half (1/2) inch tall, plated screw.Height: .50 inches.

$4.30/ea.
In Stock
Sash Channel Filler 1/16 Rubber

p/n: 70-2170-57

Filler strip, window glass sash channel. One sixteenths (1/16) inch thick by 1-1/2 inches wide. For all applications fitting glass to sash channel not requiring weatherlip type of filler. This is the highest quality rubber like polymer designed for settin

$4.29/ft.
In Stock
Door or tailgate bumper

p/n: 33-1228-71

Bumper pads, door or tailgate. Twin retainer style. Three eighths (3/8) inch by seven eighths (7/8) inch by one half (1/2) inch high.

$4.20/ea.
In Stock
Shock absorber bushing

p/n: 70-0541-33

Bushing, shock absorber mounting. Five eighths (5/8) inch hole, one and one fourth (1-1/4) inch outside diameter, five eighths (5/8) inch thick.

$4.10/ea.
In Stock
Sash channel filler 1/32 cork

p/n: 70-1114-57

Filler strip, window glass sash channel. One thirty seconds (1/32) inch thick by 1-1/2 inches wide. For all applications fitting glass to sash channel not requiring weatherlip type of filler. This is the highest quality linen back, rubber cork composition

$3.99/ft.
In Stock
Sash Channel Filler 1/32 Rubber

p/n: 70-2169-57

Filler strip, window glass sash channel. One thirty seconds (1/32) inch thick by 1-1/2 inches wide. For all applications fitting glass to sash channel not requiring weatherlip type of filler.

$3.99/ft.
In Stock
Door bumper

p/n: 33-1227-71

Bumper, door edge, twin retainer style, three eighths (3/8) inch wide by seven eighths (7/8) inch long by three eighths (3/8) inch high.

$3.50/ea.
In Stock
Shock absorber bushing

p/n: 70-0547-32

Bushing, shock absorber mounting. Double cone style, rear. Five eighths (5/8) inch hole, one and one sixteenths (1-3/16) inch outside diameter, three fourth (3/4) inch thick.

$3.50/ea.
In Stock
Gearshift bushing

p/n: 32-0051-24

Insulator (bushing). Gearshift selector rod. Sheet Metal Hole: 9/16" Center Hole: 3/8" Outside Diameter: 5/8" Slot Width: 5/32"

$3.30/ea.
In Stock
Trunk floor pan plug

p/n: 35-0070-87

Plug, trunk and floor pan drain hole. Buick 1950-65 Plug, trunk and floor pan drain hole.

$3.20/ea.
In Stock
Door weatherstrip fastener

p/n: 60-0260-73

Clip, retainer for door edge weatherstrip. Two (2) prong type with oval screw hole, spring steel, cadmium plated.Width: .875 inches. Height: .9375 inches.

$3.10/ea.
In Stock
Hood bumper

p/n: 70-0294-42

Bumper, hood rest, cap type for adjustable screw, fifteenth sixteenths (15/16) inch, seven sixteenths (7/16) inch thick.

$3.00/ea.
In Stock
Door weatherstrip fastener

p/n: 50-0198-73

Fastener, door edge weatherstrip, steel. One half (1/2) inch long, thirteen thirty second (13/32) inch diameter head, black finish.

$2.50/ea.
In Stock
Lock cylinder gasket

p/n: 60-0641-69

Gasket, door or trunk lock cylinder. Exact reproduction

$2.10/ea.
In Stock