Spring Shackle Bushing Set
p/n: 20-1834-32
This Spring Shackle Bushing Set is for the rear of the rear leaf spring on car models and the front of the front leaf spring on truck models. Two (2) sets needed per vehicle.
Body to Frame Mounting Pad
p/n: 60-0188-48
This Body to Frame Mounting Pad with locating collar functions as a body to frame isolator mounting pad. Molded from a top-quality EPDM rubber with a metal core, locating collar, and metal bolt. Two (2) required per vehicle.
Vent Window Division Post Weatherstrips
p/n: 20-1892-56
This Front Vent Window Division Post Weatherstrip pair is designed from the original part for superior fitment and seal. This piece mounts on the back edge of the vertical vent window division post.
Steering Column Tube To Floor Gasket
p/n: 20-1531-88
This Steering Column Tube To Floor Gasket is designed from the original part for superior fitment and sealing. This part fits around the steering column to seal the column tube through the body floor pan.
Radiator Mounting Pad Set
p/n: 20-0641-31
This Radiator Mounting Pad Set is designed from the original parts for a factory like appearance and function.
Fender Skirt Edge Weatherstrip
p/n: 20-1862-44
This Fender Skirt Edge Weatherstrip pair is designed from the original part for superior fitment and seal. For original skirts only this seal fits between fender skirt and rear fender body.
Front Stabilizer Bar End Link Set
p/n: 70-2109-33
A twenty-two (22) piece Front Stabilizer Bar End Link set. Comes complete with fasteners, metal sleeves, metal cup washers and black rubber bushings. One (1) end link set for both sides of stabilizer bar on one (1) car.
Wiring grommet
p/n: 70-0864-15
Grommet, taillight wiring through trunk inner panel. One (1) pair per car.
Gearshift Boot
p/n: 70-2285-26
Boot, transmission control shift lever. Fully molded out of black rubber instead of original white rubber, though it could be painted like original. For vehicles with Hydra-Matic column shift
Headlight Outer Rim Seal
p/n: 27-0063-14
Headlight Outer Rim Seal - Used to seal the headlight beam retainer ring. Replaces # 5945844.
Door Lock Bumper
p/n: 70-0538-71
Bumper, door lock striker plate. Rubber with steel core, seven sixteenths (7/16) inch thick, one (1) per door. Installed in rotary latch receiver.
Brake and Clutch Pedal Pads
p/n: 25-0058-22
A pair of brake and clutch pedal pads. Two (2) per car. Length: 4 inches. Width: 2-1/2 inches.
Roof Rail Filler
p/n: 70-1763-73
This Roof Rail Filler pair installs on the front corner of the side roof rail, just in front of the flipper seal. Molded as left and right with molded screw holes.
Brake and Clutch Pedal Pad
p/n: 60-0218-22
Pad, brake and clutch pedal. Length: 3.75 inches. Width: 2.375 inches.
Transmission Mount
p/n: 20-1269-11
This Transmission Mount is designed from the original part for a correct fitment. Mounts at the rear of manual and automatic transmissions.
Vent Window Division Post Weatherstrips
p/n: 20-1891-56
Front vent window division post seal. Fully molded with metal core and attaching tabs.
Steering Column Connecting Rod Seal
p/n: 60-0400-36
Steering column steering connecting rod seal. Power steering models require one (1) per car. Non-power steering models require two (2) per car.
Front Fender Seal
p/n: 60-0438-45
Seal, vertical, front quarter panel (fender) to cab at rear of fender (cowl). Two (2) piece set for both sides of cab.
Lower suspension arm dust seal
p/n: 70-0646-32
Seal, lower suspension arm, inner. Four (4) piece set.
Fuel Filler Dust Shield
p/n: 70-2783-45
This Fuel Filler Dust Shield is designed from the original part for superior fitment and function. Shield piece is die cut from quality masticated rubber to authentic original dimensions. Shield fits around the fuel filler neck to body.
Convertible Roof Rail Bumper
p/n: 20-1920-67
Bumpers, roof assembly to quarter panel. Four (4) piece set.
Door Bumper
p/n: 60-0334-71
Bumper, back door check link above door. Dovetail base fits check arm.Length: 1.0 inches. Width: 1.0 inches. Height: .625 inches.
Clutch and Brake Pedal Pads - Black
p/n: 50-0054-22
This reproduction Clutch and Brake Pedal Pad pair slips over the full perimeter of the pedal for a precise, factory fit. A perfect reproduction to replace worn original pedal pads. Manufactured in quality black rubber.
Fan Shroud Assembly Rubber
p/n: 70-2779-45
This two (2) piece Fan Shroud Assembly Rubber pair is designed from the original part for superior fitment and function. Shroud rubber is die cut from quality masticated rubber to authentic original dimensions. For models with Air Conditioning.
Trunk Weatherstrip
p/n: 70-0773-84
This Trunk Weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the trunk directly to the body.
1-3/8" Firewall Grommet
p/n: 70-1013-20
This Firewall Grommet is used to run the speedometer cable through the firewall. Designed from the original part for superior fit and seal.
Door Flipper Stops
p/n: 70-2853-62
This Door Flipper Stop pair is designed from the original part for superior fitment and function. These rear flipper stops mount inside the flipper opening at the very rear of the door flipper.
Fuel Neck Grommet
p/n: 60-0475-41
Grommet, fuel filler neck (1955-2nd type). Fully molded rubber, slightly oblong. Three and one half inch (3-1/2") outside width by three and fifteen sixteenths inch (3-15/16") outside length.
Liftgate Weatherstrip
p/n: 20-1963-84
This Liftgate Weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the sides and top of the liftgate opening directly to the body.
Clutch and Brake Pedal Pads
p/n: 60-0242-22
This reproduction Clutch and Brake Pedal Pad pair slips over the full perimeter of the pedal for a precise, factory fit. A perfect reproduction to replace worn original pedal pads. Manufactured in quality black rubber.
Trunk Weatherstrip
p/n: 20-1389-84
This Trunk Weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the trunk lid.
Firewall Grommet
p/n: 70-0984-20
This Firewall Grommet is used to run the wiring harness through the firewall. Designed from the original part for superior fit and seal.
Stabilizer Bar End Link Repair Set
p/n: 20-1294-33
This eleven (11) piece Stabilizer Bar End Link Repair Set is designed to withstand harsh conditions without deteriorating. Two (2) end link sets required per car.
Roof Rail Filler
p/n: 60-0429-73
This Roof Rail Filler pair installs on the front corner of the side roof rail, just in front of the flipper seal. Molded as left and right with molded screw holes. High-quality EPDM rubber a solid brass core.
Taillight Lens Gasket
p/n: 70-0951-15
Gasket, taillight lens. Die cut one eighth (1/8) inch sponge rubber. Note: Sixty Special (60 Special) will require two (2) pairs.
5" Wide Bow Drill Cloth Tape
p/n: 70-1175-65
This Bow Drill Cloth Tape is used for covering convertible side window weatherstrip. Black in color and available in a five (5) foot roll.
Windshield Frame to Cowl Weatherstrip
p/n: 70-3004-42
This Windshield Frame to Cowl Weatherstrip is designed from the original part for superior fitment and seal. This cowl rubber goes in between the windshield frame and cowl. This part also fits the 1952-1971 M38A1 model.
Body Bumper Kit
p/n: 90-0206-90
This ten (10) piece Body Bumper Kit is designed from the original part for superior fitment, finish and function. Designed from originals and made from top quality rubber to ensure durability.
Firewall Grommet
p/n: 70-1012-20
This Firewall Grommet is used to run the parking brake cable through the firewall. Designed from the original part for superior fit and seal.
Convertible Roof Rail Weatherstrip T-Bolt Set
p/n: 70-4606-67
These Convertible Top Roof Rail Weatherstrip T-Bolt reproductions are designed from the original part for superior fitment and function. This twenty two (22) t-bolts and twenty two (22) nut set fastens to the convertible top bow weatherstrips.
Window Division Bar Filler
p/n: 70-2661-62
This Window Division Bar Filler is sold as a four (4) piece set for the upper and lower. This filler set fits into inside garnish molding between rear seat side window and rear side window.
Parking Brake Pedal Pad
p/n: 50-0405-22
Pad, parking brake pedal. With "PARK" written on pad. Black only. For pedal pad without "PARK" written on pad see our #50-0348-22.Width: 2.0625 inches.
Trunk Weatherstrip
p/n: 70-1122-85
This Trunk Weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the trunk lid. The seal glues directly to the trunk lid.
Taillight Mounting Pad
p/n: 50-0100-15
Mounting pad, extrusion, taillight body-to-rear fender. Sold in sets sufficient for two (2) taillights. Length: 55.0 inches. Width: .3125 inches.
Suspension arm bumper
p/n: 70-1021-32
Bumper, front or rear suspension, upper. Uses two (2) per car on front suspension, one (1) per car on rear.
Rear Bumper Gravel Shield
p/n: 60-0213-30
This Rear Bumper Gravel Shield, also known as a rear bumper face bar-to-body seal, is made of high quality dense rubber. This seal is the exact profile as original.
Fender Skirt Edge Weatherstrip
p/n: 20-1316-44
This Fender Skirt Edge Weatherstrip pair is designed from original for superior fitment, finish, and seal. This weatherstrips fits between the rear wheel fender skirt and the rear fender quarter panel.
Splash Apron
p/n: 20-1867-45
This four (4) piece Splash Apron pair is designed from the original part for superior fitment and seal. Installs on the fender splash apron.
Rigid Run Channels
p/n: 70-0516-58
This Rigid Run Channel pair is zinc plated steel with black cloth inside lining to provide a smooth sliding surface for glass movement. Also works to protect the glass. Fastens in place by small screws or rivets on top and bottom.
Convertible A-Pillar Post Weatherstrips
p/n: 20-1912-63
This Convertible A-Pillar Post Weatherstrip pair is designed from the original part for superior fitment and sealing.. These windshield post weatherstrips attach to the body to seal between the A-pillar post and the front section of the door or vent window frame when the door is closed.
Firewall Grommet
p/n: 70-0967-20
This Firewall Grommet is used to run the windshield washer, vacuum lines, antenna lead, and other wires through the firewall. Designed from the original part for superior fit and seal.
Windshield Post to Door Seal
p/n: 70-0304-73
Weatherstrip, windshield post, upper to door. Seals between front door vent window frame and windshield pillar. Top quality rubber made to original cross-section. Two (2) strips approximately fifteen (15) inches long. May need to trim ends to fit.
Front Door Hinge Pillar Weatherstrips
p/n: 70-0552-73
This Front Door Hinge Pillar Weatherstrip pair is designed from the original parts for superior fitment and seal. The pair attaches above the beltline, hinge pillar windshield post. These two (2) strips with pre-installed clips, one for each door, are manufactured for a factory like fit.
Wiring grommet
p/n: 70-2113-20
Grommet, main wiring harness through firewall. Fully molded with proper lips and pass through holes for electrical lines.
Spring Shackle Bushing Set
p/n: 20-1836-32
This Spring Shackle Bushing Set is for the front of the rear leaf spring. One (1) set completes one spring.
Vent division bar weatherstrip
p/n: 20-1893-56
Front vent window division post seal. Fully molded with metal core and attaching tabs.
Side Window Sash Channel
p/n: 70-0641-58
This Side Window Sash Channel is the u-shaped steel channel only, no filler. Sold in 4 foot strip, usually sufficient for two (2) windows.
Peel-N-Stick Trunk Weatherstrip
p/n: 20-1389-WT
This Peel-N-Stick Trunk Weatherstrip is designed for superior fitment and seal. The weatherstrip mounts around the full perimeter of the trunk directly to the body. Easy to install 3M Peel-N-Stick backing provides superior adhesion for reliable performance.
Fender Skirt Edge Weatherstrip
p/n: 60-0201-45
This Fender Skirt Edge Weatherstrip pair is designed from the original part for superior fitment and seal. This weatherstrips fits between the removable fender skirt and the rear fender quarter panel.
Peel-N-Stick Trunk Weatherstrip
p/n: 70-0773-WT
This Peel-N-Stick Trunk Weatherstrip is designed from the original part for superior fitment and seal. The weatherstrip mounts around the full perimeter of the trunk directly to the body.
Headlight Mounting Pad
p/n: 70-0201-14
This Headlight Mounting Pad is designed from the original part for superior fitment and seal. This pad acts as the headlight adjusting collar. Sold as a pair.
Accelerator Pedal Pad
p/n: 60-0301-41
Pad, accelerator pedal. Slipover cover type. Exact copy. Fits original steel core. Length: 8.0 inches.
Front Stabilizer Bushing
p/n: 60-0088-34
This Front Stabilizer Bushing pair is fully molded from EPDM dense rubber to ensure durability. Used to connect the stabilizer bar to the vehicle frame. Two (2) required per car.