1" Floor Pan Grommet
p/n: 35-0515-20
This Floor Pan Grommet is fully molded and designed from the original part for superior fitment and seal. This grommet is made from high-quality EPDM dense rubber to provide excellent durability.
Hood to Cowl Bumper
p/n: 70-1249-42
Bumper, hood to cowl, intermediate. Attaches to our hood to cowl weatherstrips. Use as required, four (4) to six (6) per car.
Hood to Cowl Bumper
p/n: 70-1247-42
Bumper, hood to cowl, intermediate. Attaches to our hood to cowl weatherstrips, .28 inch high. Use as required four (4) to six (6) per car.
1-3/16" Utility Plug
p/n: 35-0099-20
This Utility Plug is fully molded and designed from the original part for superior fitment and seal. This plug is made from high-quality EPDM dense rubber to provide excellent durability.
Hood Bumper
p/n: 70-1607-42
This Hood Bumper is a quality reproduction of the original factory part. These rubber bumpers attach to support / cushion the hood closure.
Wiring grommet
p/n: 20-1801-17
Grommet, license plate light wire. Installs where wire comes in rear bottom of trunk.
Steering Column Floorplate
p/n: 20-0587-36
This Steering Column Floorplate pad wraps between the steering column and bracket. The pad is used to reduce noise between the steering column and the dash.
Hood to Cowl Bumper
p/n: 70-1248-42
Bumper, hood to cowl, intermediate. Attaches to our hood to cowl weatherstrips, .34 inch high. Use as required four (4) to six (6) per car.
Shock Absorber Grommet
p/n: 60-0235-33
This Shock Absorber Grommet is fully molded and designed from the original part for superior fitment and durability. The grommet the plain cylinder type with flat ends for shock absorber mounting.
5/8" Door Weatherstrip
p/n: 70-0219-73
The Door Weatherstrip is designed for 1941-1957 GM and Mopar vehicles but with its generic shape it has many uses outside of its original purpose. Available by the foot.
Rear of Door Bumper
p/n: 70-2613-71
This Rear of Door Bumper is a quality reproduction of the original factory part. This rubber door bumper attaches to support / cushion the door closure. Usually requires four (4) bumpers each per vehicle.
Glovebox or Fuel Tank Filler Door Bumpers
p/n: 20-1220-88
This Glovebox or Fuel Tank Filler Door Bumper pair is a quality reproduction of the original factory part. This push on rubber bumper attaches to support / cushion the glovebox or filler door closure.
Spring shackle seal
p/n: 70-1125-33
Washer, front and rear spring shackle, seal for shackle pin. Constructed of neoprene.
Control arm bushing seal
p/n: 60-0094-32
Seal, upper and lower control arm cross shaft bushing, at inner end of arm.1939-48: Lower only, all pass. (exc.
Stabilizer Link or Shock Grommet
p/n: 70-0737-33
This Stabilizer Link or Shock Grommet is designed from the original part for superior fitment and usage. Fully molded rubber.
Door Drain Hole Seal
p/n: 60-0442-70
This Door Drain Hole Seal installs on the door bottom and is also used on the tailgate of station wagons. Two (2) required per vehicle. Molded from high-quality EPDM dense rubber.
5/8" Door Weatherstrip without Clips
p/n: 70-1111-73
This Door Weatherstrip made from high-quality EPDM sponge rubber. Excellent for use on many different vehicle models. Available by the foot.
Trunk Bumper
p/n: 20-1923-67
Bumpers, package tray panel. Glues on bottom of trunk lid door where front of package tray panel contacts bottom of trunk lid.
Front Fender Pads
p/n: 20-1866-45
This Front Fender Pad pair is designed from the original part for superior fitment and seal. These weatherstrip pads fit at the top rear of the front fender to cowl panel.
2-1/4" Body Hole Plug
p/n: 35-0863-45
This Body Hole Plug is fully molded and designed from the original part for superior fitment and seal. Designed for the trunk, however the generic shape makes this plug usable for a variety of applications.
1" Trunk Weatherstrip
p/n: 70-0510-85
This Trunk Weatherstrip was designed from an original part for a specific application but has many uses outside of its original purpose. Available by the foot.