Kit, body to frame pad.
This front door vent window weatherstrip kit is a four (4) piece set that contains the main vent window seals and division post seals. All of the pieces were designed from original parts for a precise, factory fit.
This rear window gasket mounts around the full perimeter of the back glass and has properly molded corners for a precise, factory fit. It also has the slot to accommodate the outer edge's decorative molding.
Bushing and bracket kit, front stabilizer bar. Includes: Two (2) each of #5492 and 5476, four (4) each of #5493 and attaching parts.
These front door vent window weatherstrips are the main seals needed to replace the rubber on your vent windows. They are designed and molded from original parts for superior fitment and seal.
This windshield gasket is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the front glass and has vulcanized, or bonded, ends which means no cutting or splicing is required for installation. It also has the slot to accommodate the outer edge's decorative molding.
Weatherstrip, door. Installs on inner dog leg.
Deflector, rear stone. Rubber. Installs between body and rear bumper. Includes fasteners.
Side window vertical leading edge weatherstrip.
Mount, front motor. Two (2) required per car.
Bushings, stabilizer bar to frame. Four (4) piece set.
Window felt inner and/or outer. Flexible, pile lined, rubber covered, with black bead. Available in 3ft pair.
Seals, air vent inlet duct to heater outside.
Weatherstrip, door window inner and outer, front and rear doors. Bend to fit. Available in a 3ft pair.
Channel, door glass run. Lock side. Rear of front door. Your original brackets attach to this.
Window felt inner and/or outer. Flexible, pile lined, rubber covered, with black bead. Available in 3ft pairs.
This Peel-N-Stick Trunk Weatherstrip is designed for superior fitment and seal. The seal mounts around the full perimeter of the trunk directly to the body. Easy to install 3M Peel-N-Stick backing provides superior adhesion for reliable performance.
Front vent window division post seal. Fully molded with metal core and attaching tabs.
Shackle kit, front of rear spring. Kit completes one spring.
Tube, windshield cowl drain.
Seal, front fender splash apron to frame.
This trunk weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the trunk lid.
Seals, air vent damper rubber.
Seal, vent window upper tip at door window post.
Bushing, brake master cylinder. Installs on push rod.
This Transmission Mount is designed from the original part for a correct fitment. Mounts at the rear of manual and automatic transmissions.
This Fender Skirt Edge Seal pair is designed from the original part for superior fitment and seal. For original skirts only this seal fits between fender skirt and rear fender body.
Bolt and bushing kit, rear of rear spring shackle. Enough for one (1) side only.
Bumper, front suspension lower arm.
Insulator, transmission gear shift column lever.
Insulator, gear shift.
Set, spring clamp liner. Front spring takes eight pieces for both sides Rear spring takes four pieces for both sides. Six (6) piece set.
Seal, steering column tube. Installs on top of floor mat.
Seal, front fender splash apron to fender anti-squeak. Seventy two (72) inch strip.
Pads, taillight to body.
Seal, steering column to floor. Installs under floor mat.
Bumper, front suspension upper arm. Three eighths (3/8) inch by three fourths (3/4) inch bolt, twenty four (24) threads.
Bumper, front suspension lower arm. Without stud.
Grommet, fuel filler neck. Fully molded flexible rubber. Four inch (4") outside diameter by two and one eighth inch (2-1/8") inside diameter by one half inch (1/2") height.
Bumpers, top of cowl to hood.
Kit, cowl lacing. Rubber.
Pad, brake and clutch pedal. Replacement type.
Seals, ventilator air inlet duct door to duct inside.
Pad, rear mount antenna.
Seal, garnish molding to dash rubber. Eighty four (84) inches long. Replaces factory #B7A-7003127-E.
Seals, cowl top ventilator grille anti-squeak. U-shaped.
Pads or gaskets for the outside door handles. Front or rear, this is a four (4) piece set.
This Window Sash Channel Weatherstrip is designed from the original part for superior fitment and seal. Thirty four and three-fourths (34-3/4") inch long EPDM extrusion that goes between glass and metal sash lift channel. One (1) roll required per window.
Seal, garnish molding to dash rubber. Forty six (46) inches long. Models WITH A/C. Replaces factory #B7A-7003127-B.