Search Results
Please click on the part name in red in order to get a complete description.
Body Weatherstrip Kit
p/n: 90-3062-90
This kit includes the major weatherstrip components and some other essential parts needed for the body of your restoration project.
Convertible roof rail kit
p/n: 70-0757-65
Convertible roof rail weatherstrip. This part fits on the folding roof of the vehicle and seals the side window when the window is fully raised.
Front Door Vent Window Kit
p/n: 90-0412-90
This front door vent window weatherstrip kit is a four (4) piece set that contains the main vent window seals and division post seals. All of the pieces were designed from original parts for a precise, factory fit.
Bumper guard cap
p/n: 70-0883-30
Caps, front bumper guard. Rubber with molded in plate and bolt. A high quality reproduction. Four and seven eighths inch (4-7/8") outside diameter.
Front Door Vent Window Weatherstrips
p/n: 38-0074-55
These front door vent window weatherstrips are the main seals needed to replace the rubber on your vent windows. They are designed and molded from original parts for superior fitment and seal.
Front Motor Mount Revulcanizing Service
p/n: 70-0548-11
This Front Motor Mount revulcanizing service replaces the rubber in your original Motor Mounts to make them like new again. The process is designed for the original factory mounts only. Send in cores and allow three weeks for service.
Windshield Gasket
p/n: 70-0820-50
This windshield gasket mounts around the full perimeter of the front glass and has properly molded corners for a precise, factory fit. It also has the slot to accommodate the outer edge's decorative molding.
Front Door weatherstrip
p/n: 70-0848-72
Door edge weatherstrip with molded ends. This part is the primary door to body weatherstrip. Includes pins and clips for easy installation.
Cadillac Master Parts List 1948 - 1959 (Reprint)
p/n: 07-1442-07
This 1948 - 1959 Cadillac Master Parts List - Two (2) Volume set licensed Detroit Iron reprint provides the most comprehensive repair information in paper format. This OEM PARTS manual reproduction provides detailed original part numbers, part assembly diagrams / illustrations and part textual details for all vehicle subsystems. This information set is a high quality reproduction of the exact parts manual originally published for use by Cadillac dealer mechanics.
Motor mount service
p/n: 70-0674-11
Cushion, motor support, rear on transmission to cross member. Revulcanization service only.
Cadillac Master Parts List 1957 - 1964 (Reprint)
p/n: 07-1443-07
This 1957 - 1964 Cadillac Master Parts List - Two (2) Volume set licensed Detroit Iron reprint provides the most comprehensive repair information in paper format. This OEM PARTS manual reproduction provides detailed original part numbers, part assembly diagrams / illustrations and part textual details for all vehicle subsystems. This information set is a high quality reproduction of the exact parts manual originally published for use by Cadillac dealer mechanics.
Splash apron
p/n: 70-2493-45
Filler, splash apron. Die cut masticated rubber to authentic original dimensions. Includes all factory style holes required for installation.
Rigid run channel
p/n: 70-0536-58
Run channel, front door window, for full length of division bar (approximately twenty nine (29) inches). Rigid, bright beaded edge, mohair lined channel, die trimmed and formed at top.
Upper suspension arm dust seal
p/n: 70-0890-32
Seal, upper A-arm, inner and outer. Four (4) piece set.Height: 1.0 inches.
Stabilizer bushing
p/n: 70-0627-33
Bushings, stabilizer bar, front. Fully molded rubber. One and three fourths inch (1 3/4") length by one and one half inch (1 1/2") width by three fourths inch (3/4") inside hole diameter by one and five eighths inch (1 5/8") height.
Steering column floorplate
p/n: 70-1425-88
Seal, steering column to firewall. For 1956 vehicles purchase our #70-1509-88 grommet separately. For 1957-58 vehicles purchase our #70-2316-88 grommet separately.
Fenderskirt Edge Seal
p/n: 70-0154-45
Seal, fenderskirt edge, exact copy, trim notch for skirt lock at installation. Compare sketch with your original to be sure. Two (2), five (5) foot strips.
U Jamb lock pillar filler
p/n: 70-0729-79
Door lock pillar seal. This part seals the bottom of the rear side window, and may also be known as a door jamb seal.
Hood To Cowl Weatherstrip
p/n: 70-0827-42
This Hood to Cowl Weatherstrip is designed from the original part for superior fitment and seal. An exact reproduction of the original profile. This seal mounts at the rear of the engine bay to seal between the hood and vehicle body cowl.
Radiator support weatherstrip
p/n: 70-2780-45
Seal, radiator support kit. Die cut masticated rubber to authentic original dimensions. Includes all factory style holes required for installation.
Steering column grommet
p/n: 70-2316-88
Grommet, steering column at floor. Order our #70-2316-88 seal separately.
Axle rebound pad
p/n: 70-2225-32
Bumper, rear spring axle impact. Located on frame rail. Rubber only, does not include metal retaining clips or bolts.Width: 1.9375 inches. Height: 2.
Door weatherstrip
p/n: 70-0552-73
Weatherstrip, front door, auxiliary on body above beltline, hinge pillar windshield post. Two (2) strips, each thirteen and three eighths (13-3/8) inches long with retaining clips.
Door weatherstrip
p/n: 70-0551-73
Weatherstrip, front door auxiliary, on door at beltline, right and left. Uses snap-in fasteners, four (4) each included.
Front coil spring pad
p/n: 70-2302-35
Pad, front coil spring insulator cushion. Fully molded, mounts at top of front coil springs.
1935-1974 Cadillac Factory Parts Manual, CD
p/n: 07-1346-07
This GM Licensed Detroit Iron CD provides the most comprehensive set of digital Cadillac Factory parts manuals. The factory manuals on this CD were professionally scanned from the original service and parts manuals.
1957-1958 Cadillac Factory Shop Manual, CD
p/n: 07-1057-07
This GM Licensed Detroit Iron CD provides the most comprehensive set of digital Cadillac Factory shop repair manuals. The factory manuals on this CD were professionally scanned from the original service and parts manuals.
Front Stabilizer Bar End Link Kit
p/n: 70-2109-33
Kit, front stabilizer bar link assembly replacement. Twenty-two (22) piece set. One (1) set for both sides of one (1) car. Hex head bolt. 5/16"-24nf x 7- 5/8" lg. Comes with metal sleeve, metal cup washers and rubber grommets.
Body Anti-Squeak Rubber
p/n: 60-0054-73
Bulb type seal, gravel shield-to-rear bumper, anti-squeak. Also used as a door weatherstrip for some makes and models. Twelve (12) foot strip.
Run Channel Upper Bumper
p/n: 60-0183-62
Bumper, side window glass in vent frame at top, right and left, brass core.Length: 1.625 inches.
Rigid Run Channel
p/n: 70-0347-58
Channel, rigid run, window division bar. Stainless beaded edge, mohair-lined, exact replacement for rear side of division bar.
Window Sash / Beltline Channel
p/n: 70-0651-58
Weatherstrip, window sash channel (beltline), inner. Rigid, rubber covered weatherstrip with flock lining and one fourth (1/4) inch chrome edge. Used on front door, rear door and rear quarter window. Six (6) foot strip.
Battery cable grommet
p/n: 70-2318-20
Grommet, battery cable through radiator shroud. Reproduction of original rectangular design exactly. Replaces #1469080. Length: 2.4375 inches. Width: 1.5 inches.
Rear bumper end filler set
p/n: 70-3769-30
Seal, rear bumper end. Die cut masticated rubber to authentic original dimensions.
Headlight seal
p/n: 70-1465-14
Seal, headlight outer rim to sealed beam retainer ring. Possible fit for models with dual headlights.Width: .375 inches. Height: .9375 inches.
Vent division bar weatherstrip
p/n: 70-0922-56
Front vent window division post seal. Fully molded with metal core and attaching tabs.
Peel-N-Stick Trunk Weatherstrip
p/n: 70-0773-WT
This trunk weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the trunk directly to the body. Easy to install 3M Peel-N-Stick backing provides superior adhesion for reliable performance.
Hood Bumper
p/n: 70-0501-42
Bumpers, hood. Four (4) per set.Length: 1.4375 inches. Width: .5625 inches.
Steel sash channel
p/n: 70-0641-58
Sash channel, side window glass. U-shaped steel channel only, no filler. Will require that you attach your own window regulator cam to underside as required.
Rear Wheelhouse Seals
p/n: 70-2782-45
This Rear Wheelhouse Seal pair is die cut masticated rubber made to authentic original dimensions. Includes all factory style holes for installation.
Fan shroud assembly seal
p/n: 70-2779-45
Seal, fan shroud assembly. Die cut masticated rubber to authentic original dimensions. Includes all factory style holes required for installation.
Trunk Weatherstrip
p/n: 70-0773-84
This trunk weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the trunk directly to the body.
Firewall grommet
p/n: 70-0967-20
Grommet, used for windshield washer, vacuum lines, antenna lead, and others through firewall.
Rigid run channel
p/n: 70-0516-58
Channel, rigid run, lower side window below beltline, zinc plated steel with black cloth lining, one half (1/2) inch deep by one half (1/2) inch wide, fifteen (15) inches long.
Suspension arm bumper
p/n: 70-1021-32
Bumper, front or rear suspension, upper. Uses two (2) per car on front suspension, one (1) per car on rear.
Bowdrill cloth tape
p/n: 70-1175-65
Tape, black bowdrill cloth. Adhesive backed, used to create cloth cover surface for side rail weatherstrips typically. Five (5) inches by five (5) foot roll. Pressure sensitive, for covering convertible side window weatherstrip such as our #70-1170-99 or
Fuel filler dust shield
p/n: 70-2783-45
Seal, gas filler dust shield. Die cut masticated rubber to authentic original dimensions. Includes all factory style holes required for installation.
Inner fender seal
p/n: 70-2781-45
Seal, inner fender to bumper. Die cut masticated rubber to authentic original dimensions. Includes all factory style holes required for installation.
Lower suspension arm dust seal
p/n: 70-0646-32
Seal, lower suspension arm, inner. Four (4) piece set.
Wiring grommet
p/n: 70-0864-15
Grommet, taillight wiring through trunk inner panel. One (1) pair per car.
Metal sleeved grommet
p/n: 70-0203-41
Flanged rubber grommet with metal sleeve bushing. Used as part of the accelerator relay lever. Also used from 1959-61 on all Cadillac models as a bushing for the windshield wiper relay lever adaptor.
Trunk bumper
p/n: 70-0296-87
T-nut, trunk bumper in gutter at sides, brass core tapped 10-32 thread. Two (2) required per car. For models having partial weatherstrip in gutter of body.
Battery clamp cover
p/n: 70-0095-21
Cover, battery clamp. Control unsightly sulfate buildup. Help protect the nearby metal and finish. Good copy from original part.Length: 3.5 inches.
Rocker panel dust shield cover
p/n: 70-2392-45
Cover, rocker panel inner dust shield. Fully molded with proper attaching teeth and flap.
Inner fender seal
p/n: 70-3080-45
Filler, front auxiliary wheel house to inner fender. Two (2) piece set. Die cut masticated rubber.
Bowdrill cloth tape
p/n: 70-1172-65
Tape, black bowdrill cloth. Adhesive backed, used to create cloth cover surface for side rail weatherstrips typically. Two and one half (2-1/2) inches by five (5) foot roll. Pressure sensitive, for covering convertible side window weatherstrip such as our
Window stop stem bumper
p/n: 33-0675-62
Cushion (stem bumper), window stop, lower. For front and rear door, rear side and quarter windows as required. (See sketch and our #33-0540-62).
Parking brake pedal pad
p/n: 70-1273-22
Pad, parking brake locking pedal.Length: 2.0625 inches. Width: 1.5 inches.
Glovebox door check grommet
p/n: 70-0968-88
Grommet, glove box door cushion. One and three quarters long (1-3/4") and thirteen sixteenths (13/16")wide.Length: 1.75 inches. Width: .8125 inches.
Tan bowdrill cloth tape
p/n: 70-1173-65
Tape, brown (tan) bowdrill cloth. Adhesive backed, used to create cloth cover surface for side rail weatherstrips typically. Two and one half (2-1/2) inches by five (5) foot roll. Pressure sensitive, for covering convertible side window weatherstrip such
Body Mounting Pad
p/n: 50-0361-48
Pad, body mounting. Required replacement for body-off restorations. Constructed of high quality rubber for long lasting durability. Two inch (2") square by fifteen sixteenths inch (15/16) inside hole diameter by one fourth inch (1/4") height.
Masticated rubber sheet
p/n: 70-0645-45
Masticated sheet. Three thirty seconds (3/32) inch thick rubber sheet containing random milled cotton cord reinforcement for front end splash aprons, etc. This product is a four (4) foot wide roll, and will only be sold in four (4) square foot multiples
Body Mount Isolator
p/n: 70-2232-48
Isolator, body mounting to chassis. Fully molded rubber. One and seven eighths inch (1 7/8") outside diameter by fifteen sixteenths inch (15/16") inside hole diameter by nine sixteenths inch (9/16") height.
Window stop stem bumper
p/n: 33-0622-62
Bumper, window stop. One and one fourth (1-1/4) inch square by one half (1/2) inch thick. Compare with our #33-0540-62 and #33-0675-62.Length: 1.
Instrument panel grommet
p/n: 70-1654-88
Grommet, instrument panel to windshield frame. Two (2) to six (6) required.Length: 1.3125 inches. Width: 1.0625 inches.
Headlight dimmer switch pad
p/n: 70-0930-14
Pad, headlight dimmer switch. Rubber slip-over cover for floor mounted switch.
Hood bumper
p/n: 70-0973-42
Bumper, front hood adjuster. Our #70-0294-42 type cap attached to 5/16-18 threaded bolt. In 1957-1958 use four (4) per vehicle. In 1959-1960 use two (2) per vehicle.
Window stop stem bumper
p/n: 33-0540-62
Cushion (stem bumper), window stop, lower. For front and rear door, rear side and quarter windows as required.
Trunk bumper
p/n: 34-0399-87
Bumper, trunk opening on lid. Metal core, as original, screw held. Two (2) required per car.
Brown door lock knob
p/n: 70-0660-70
Knob or push button for inside door lock, fits over 1/8" steel rod to door lock. Hard brown rubber, may be lacquered other colors as required.
Parking brake pedal pad
p/n: 70-1274-22
Pad, parking brake release pedal.Length: 2.625 inches. Width: .8125 inches.
Run channel mohair liner
p/n: 70-2863-58
Liner, mohair. Liner with a rubber backing. Apply with adhesive to division bars and channels. Helps reline guide bars on lock side of hardtops and convertibles.
Peel-N-Stick Trunk Weatherstrip
p/n: 70-0510-WT
Peel-N-Stick Trunk Weatherstrip made from high quality EPDM sponge rubber. 3M Peel-N-Stick backing provides superior adhesion for reliable performance. Makes for an easier installation of deck lid weatherstripping. Also excellent for use in many different applications and on many different vehicle models.
Trunk Weatherstrip
p/n: 70-0346-85
This weatherstrip was designed from an original part for a specific application but has many uses outside of its original purpose. The seal is structured to be applied to the body of the car.
Trunk Weatherstrip
p/n: 70-0510-85
This weatherstrip was designed from an original part for a specific application but has many uses outside of its original purpose. The seal is structured to be applied to the body of the car.
Universal mounting pad
p/n: 70-0308-17
Mounting pad, continuous for lights, hinges, brackets, and other bright work when no molded pad is available.
Body hole plug
p/n: 35-0863-45
Plug, body sheet metal holes. Used in various places (like trunks). For one and one half (1-1/2) inch hole in body.
Door drain hole seal
p/n: 60-0442-70
Weatherstrip, door bottom drain hole seal. Also used on tailgate of station wagon. (Two (2) required for this use).Length: 4.0 inches.
Stabilizer or shock grommet
p/n: 70-0737-33
Grommet, front stabilizer link or shock absorber. Fully molded rubber. One and one eighths inch (1 1/8") by three eighths inch (3/8") inside hole diameter by seven eighths inch (7/8") height. Use as a front stablizer link for 1946-1970 Cadillac: All mode
Hood to cowl bumper
p/n: 70-1248-42
Bumper, hood to cowl, intermediate. Attaches to our hood to cowl weatherstrips, .34 inch high. Use as required four (4) to six (6) per car. For .
Hood to cowl bumper
p/n: 70-1247-42
Bumper, hood to cowl, intermediate. Attaches to our hood to cowl weatherstrips, .28 inch high. Use as required four (4) to six (6) per car. For .
Hood to cowl bumper
p/n: 70-1249-42
Bumper, hood to cowl, intermediate. Attaches to our hood to cowl weatherstrips. Use as required, four (4) to six (6) per car. For .
Sash channel filler 1/16 cork
p/n: 70-1115-57
Filler strip, window glass sash channel. One sixteenths (1/16) inch thick by 1-1/2 inches wide. For all applications fitting glass to sash channel not requiring weatherstrip type of filler. This is the highest quality linen back, rubber cork composition on
Firewall retainer
p/n: 60-0586-20
Retainer, firewall insulation panel. "Christmas Tree" style popular during this time. Constructed of vinyl plastic. Up to ten (10) required per car.
Power top cylinder spacer
p/n: 70-0822-67
Spacer, folding top power cylinder support. Four (4) used per car.
Door lock bumper
p/n: 34-0484-71
Bumper, door lock post, upper, one half (1/2) inch diameter by one half (1/2) inch tall, plated screw.Height: .50 inches.
Sash Channel Filler 1/16 Rubber
p/n: 70-2170-57
Filler strip, window glass sash channel. One sixteenths (1/16) inch thick by 1-1/2 inches wide. For all applications fitting glass to sash channel not requiring weatherlip type of filler. This is the highest quality rubber like polymer designed for settin
Door or tailgate bumper
p/n: 33-1228-71
Bumper pads, door or tailgate. Twin retainer style. Three eighths (3/8) inch by seven eighths (7/8) inch by one half (1/2) inch high.
Filler and cushion strip
p/n: 70-1237-48
Filler and cushion strip, many applications. Five thirty seconds (5/32) inch by one and five eighths (1-5/8) inch.