Kit, body to frame pad.
This rear window gasket set contains the seals that mount around all of the back glass pieces. The three (3) piece set has properly molded corners for a precise, factory fit and it also has the slot to accommodate the outer edge's decorative molding.
This front door vent window weatherstrip set is a four (4) piece set that contains the main vent window seals and division post seals. All of the pieces were designed from original parts for a precise, factory fit.
Bushing and bracket kit, front stabilizer bar. Twenty-six (26) piece set. Includes: four (4) rubber bushings, two (2) metal inner brackets, two (2) outer metal brackets, six (6) bolts, six (6) washers and six (6) nuts.
These front door vent window weatherstrips are the main seals needed to replace the rubber on your vent windows. They are designed and molded from original parts for superior fitment and seal.
This windshield gasket is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the front glass and has vulcanized, or bonded, ends which means no cutting or splicing is required for installation. It also has the slot to accommodate the outer edge's decorative molding.
Weatherstrip, door. Installs on inner dog leg.
Deflector, rear stone. Rubber. Installs between body and rear bumper. Includes fasteners.
Channel, side window glass, vertical run. Flexible, felt lined, rubber covered channel. Available 60" lengths.
Channel, flexible door window run. Stainless steel beaded. Available in 5ft lengths.
Mount, front motor. Two (2) required per car.
Bushings, stabilizer to frame. Four (4) piece set.
Window felt inner and/or outer. Flexible, pile lined, rubber covered, with black bead. Available in 3ft pair.
Seals, air vent inlet duct to heater outside.
Weatherstrip, door window inner and outer, front and rear doors. Bend to fit. Available in a 3ft pair.
Window felt inner and/or outer. Flexible, pile lined, rubber covered, with black bead. Available in 3ft pairs.
Tube, windshield cowl drain.
Seal, front fender splash apron to frame.
Seals, air vent damper rubber.
Bushing, brake master cylinder. Installs on push rod.
This Transmission Mount is designed from the original part for a correct fitment. Mounts at the rear of manual and automatic transmissions.
This Fender Skirt Edge Seal pair is designed from the original part for superior fitment and seal. For original skirts only this seal fits between fender skirt and rear fender body.
Front vent window division post seal. Fully molded with metal core and attaching tabs.
Insulator, transmission gear shift column lever.
Seal, steering column tube. Installs on top of floor mat.
Seal, front fender splash apron to fender anti-squeak. Seventy two (72) inch strip.
Seal, steering column to floor. Installs under floor mat.
Kit, cowl lacing. Rubber.
Pad, brake and clutch pedal. Replacement type.
Seals, ventilator air inlet duct door to duct inside.
Pad, rear mount antenna.
Seal, garnish molding to dash rubber. Eighty four (84) inches long. Replaces factory #B7A-7003127-E.
Seals, cowl top ventilator grille anti-squeak. U-shaped.
Pads or gaskets for the outside door handles. Front or rear, this is a four (4) piece set.
This Window Sash Channel Weatherstrip is designed from the original part for superior fitment and seal. Thirty four and three-fourths (34-3/4") inch long EPDM extrusion that goes between glass and metal sash lift channel. One (1) roll required per window.
Seal, garnish molding to dash rubber. Forty six (46) inches long. Models WITH A/C. Replaces factory #B7A-7003127-B.
Gaskets, parking light lens.
Insulator, steering column bracket cover to dash.
Gaskets, taillight lens to housing.
Pad, front fender mount antenna.
Grommet, main wiring loom through firewall.
Grommet, overdrive pull cable.
Gasket, headlight bulb bucket to fender.
Grommet, antenna lead-in. For front mount type.
Pad, hood ornament to hood.
Pads, top rear of front to cowl.
Bumpers, glovebox and/or fuel filler door. Used as glove box door bumpers for all models listed, used as fuel door bumper for 1950-51 cars and 57-59 retractables only.
Seal, idler arm. Two (2) required per car.
Grommet, license plate light wire. Installs where wire comes in rear bottom of trunk.
Plug, cowl and floor pan. This body plug covers a sheet metal hole that is one and one seven eighths (1-7/8) inch in diameter.