Search Results
Please click on the part name in red in order to get a complete description.
Prop shaft support service
p/n: 70-0748-27
Bearing support bracket assembly, drive shaft center bearing. Revulcanization service only. .
Defroster vent gasket
p/n: 70-2279-31
Gasket, defroster vent at base of windshield. One (1) pair required per car.Length: 14.5 inches. Height: .5625 inches.
Hood to cowl filler
p/n: 70-2258-43
Filler, hood to cowl side extension weatherstrip. Fully molded from soft rubber with all original details.
Splash apron
p/n: 70-2494-45
Filler, splash apron. Die cut masticated rubber to authentic original dimensions. Includes all factory style holes required for installation.
Rigid run channel
p/n: 70-0536-58
Run channel, front door window, for full length of division bar (approximately twenty nine (29) inches). Rigid, bright beaded edge, mohair lined channel, die trimmed and formed at top.
Upper suspension arm dust seal
p/n: 70-0890-32
Seal, upper A-arm, inner and outer. Four (4) piece set.Height: 1.0 inches.
Front suspension bumper
p/n: 70-2649-35
Bumper, front suspension, lower on A-arm. Fully molded with integral mounting bolt.Width: 2.125 inches.
Axle rebound pad
p/n: 70-2591-32
Bumper, air suspension rear axle impact. Located on frame rail. Rubber only, does not include metal retaining clips or bolts.
Stabilizer bushing
p/n: 70-0627-33
Bushings, stabilizer bar, front. Fully molded rubber. One and three fourths inch (1 3/4") length by one and one half inch (1 1/2") width by three fourths inch (3/4") inside hole diameter by one and five eighths inch (1 5/8") height.
Fenderskirt Edge Seal
p/n: 70-0154-45
Seal, fenderskirt edge, exact copy, trim notch for skirt lock at installation. Compare sketch with your original to be sure. Two (2), five (5) foot strips.
Hood To Cowl Weatherstrip
p/n: 70-1019-42
Weatherstrip, hood to cowl.Length: 47.75 inches. Width: 1.5 inches.
Axle rebound pad
p/n: 70-2225-32
Bumper, rear spring axle impact. Located on frame rail. Rubber only, does not include metal retaining clips or bolts.Width: 1.9375 inches. Height: 2.
Door weatherstrip hinge pillar
p/n: 60-0326-73
Weatherstrip, front door opening. Auxiliary on door hinge pillar at beltline, right and left. Sometimes called "L" or "J" strips. Fully molded with authentic configuration to help guide water to the outside of vehicle. Set includes four (4) button-type fa
Front coil spring pad
p/n: 70-2302-35
Pad, front coil spring insulator cushion. Fully molded, mounts at top of front coil springs.
Front Stabilizer Bar End Link Kit
p/n: 70-2109-33
Kit, front stabilizer bar link assembly replacement. Twenty-two (22) piece set. One (1) set for both sides of one (1) car. Hex head bolt. 5/16"-24nf x 7- 5/8" lg. Comes with metal sleeve, metal cup washers and rubber grommets.
Body Anti-Squeak Rubber
p/n: 60-0054-73
Bulb type seal, gravel shield-to-rear bumper, anti-squeak. Also used as a door weatherstrip for some makes and models. Twelve (12) foot strip.
Rigid Run Channel
p/n: 70-0347-58
Channel, rigid run, window division bar. Stainless beaded edge, mohair-lined, exact replacement for rear side of division bar.
Hood Bumper
p/n: 70-0501-42
Bumpers, hood. Four (4) per set.Length: 1.4375 inches. Width: .5625 inches.
Inner fender seal
p/n: 70-2786-45
Seal, inner fender. Die cut masticated rubber to authentic original dimensions. Includes all factory style holes required for installation.
Window Sash / Beltline Channel
p/n: 70-0651-58
Weatherstrip, window sash channel (beltline), inner. Rigid, rubber covered weatherstrip with flock lining and one fourth (1/4) inch chrome edge. Used on front door, rear door and rear quarter window. Six (6) foot strip.
Suspension arm bumper
p/n: 70-1021-32
Bumper, front or rear suspension, upper. Uses two (2) per car on front suspension, one (1) per car on rear.
Radiator Top Seal
p/n: 70-2784-45
This Radiator Top Seal is die cut masticated rubber made to authentic original dimensions. Upper Radiator filler with the factory style holes required for installation.
Lower suspension arm dust seal
p/n: 70-0646-32
Seal, lower suspension arm, inner. Four (4) piece set.
Fog light lens gasket
p/n: 70-3093-17
Gasket, signal and fog light lens, outer. Each car with fog lights requires 2 pairs (4 gaskets total one for each fog/signal lamp).
Rear spring pad
p/n: 70-0980-32
Pad, rear spring insulator. Two and one half (2-1/2) inches wide, with cloth reinforcement. Used upper and lower on spring. Four (4) used per car.
Metal sleeved grommet
p/n: 70-0203-41
Flanged rubber grommet with metal sleeve bushing. Used as part of the accelerator relay lever. Also used from 1959-61 on all Cadillac models as a bushing for the windshield wiper relay lever adaptor.
Body Mount Isolator Pad
p/n: 70-0929-48
Body Mount Isolator Pad - Rubber with metal core and locating collar as original part. Part dimensions = Two and three sixteenths inch (2 3/16") square by one inch (1") overall height with thirteen sixteenths inch (13/16") inside bolt diameter. Does not include any fastener hardware.
Door handle gasket kit
p/n: 70-0925-69
Gasket set, outside door handle. Die cut rubber construction. Six (6) piece set for two (2) handles.
Battery clamp cover
p/n: 70-0095-21
Cover, battery clamp. Control unsightly sulfate buildup. Help protect the nearby metal and finish. Good copy from original part.Length: 3.5 inches.
Cowl to fender seal
p/n: 70-3075-43
Seal, cowl to fender. Two (2) piece set. Die cut masticated rubber.
Bumper support bar pad
p/n: 70-0993-30
Bumper, impact bar end to body, for rear bumper. Fully molded rubber. Two inches (2") length by seven sixteenths inch (7/16") width by eleven sixteenths inch (11/16") height.
Masticated rubber sheet
p/n: 70-0645-45
Masticated sheet. Three thirty seconds (3/32) inch thick rubber sheet containing random milled cotton cord reinforcement for front end splash aprons, etc. This product is a four (4) foot wide roll, and will only be sold in four (4) square foot multiples
Body mounting pad
p/n: 70-2233-48
Pad, body mounting to chassis. Fully molded rubber. One and seven eighths inch (1 7/8") outside diameter by eleven sixteenths inch (11/16") inside hole diameter by nine sixteenths inch (9/16") height.
Body mounting pad
p/n: 70-2232-48
Pad, body mounting to chassis. Fully molded rubber. One and seven eighths inch (1 7/8") outside diameter by fifteen sixteenths inch (15/16") inside hole diameter by nine sixteenths inch (9/16") height.
Body mounting pad
p/n: 70-2234-48
Pad, body mounting to chassis. Fully molded rubber, square type. Six (6) or more are used per car. Two and three sixteenths inch (2 3/16") square by three fourths inch (3/4") inside diameter hole by one half inch (1/2") inch height.
Headlight dimmer switch pad
p/n: 70-0930-14
Pad, headlight dimmer switch. Rubber slip-over cover for floor mounted switch.
Taillight gasket
p/n: 70-0836-15
Gasket, taillight housing and molding-to-tailfin. Seven and one half (7-1/2) foot strip. Enough for both lights.Length: 90.0 inches.
Hood bumper
p/n: 70-0973-42
Bumper, front hood adjuster. Our #70-0294-42 type cap attached to 5/16-18 threaded bolt. In 1957-1958 use four (4) per vehicle. In 1959-1960 use two (2) per vehicle.
Brown door lock knob
p/n: 70-0660-70
Knob or push button for inside door lock, fits over 1/8" steel rod to door lock. Hard brown rubber, may be lacquered other colors as required.
Run channel mohair liner
p/n: 70-2863-58
Liner, mohair. Liner with a rubber backing. Apply with adhesive to division bars and channels. Helps reline guide bars on lock side of hardtops and convertibles.
Universal mounting pad
p/n: 70-0308-17
Mounting pad, continuous for lights, hinges, brackets, and other bright work when no molded pad is available.
Body hole plug
p/n: 35-0863-45
Plug, body sheet metal holes. Used in various places (like trunks). For one and one half (1-1/2) inch hole in body.
Stabilizer or shock grommet
p/n: 70-0737-33
Grommet, front stabilizer link or shock absorber. Fully molded rubber. One and one eighths inch (1 1/8") by three eighths inch (3/8") inside hole diameter by seven eighths inch (7/8") height. Use as a front stablizer link for 1946-1970 Cadillac: All mode
Door drain hole seal
p/n: 70-1042-70
Weatherstrip, door bottom drain hole.Length: 3.625 inches. Width: .40625 inches.
Sash channel filler 1/16 cork
p/n: 70-1115-57
Filler strip, window glass sash channel. One sixteenths (1/16) inch thick by 1-1/2 inches wide. For all applications fitting glass to sash channel not requiring weatherstrip type of filler. This is the highest quality linen back, rubber cork composition on
Firewall retainer
p/n: 60-0586-20
Retainer, firewall insulation panel. "Christmas Tree" style popular during this time. Constructed of vinyl plastic. Up to ten (10) required per car.
Hood Bumper
p/n: 70-1251-42
Bumper, hood to cowl weatherstrip, one fourth (1/4) inch high. For three sixteenths (3/16) inch high see our #70-1250-42.
Sash Channel Filler 1/16 Rubber
p/n: 70-2170-57
Filler strip, window glass sash channel. One sixteenths (1/16) inch thick by 1-1/2 inches wide. For all applications fitting glass to sash channel not requiring weatherlip type of filler. This is the highest quality rubber like polymer designed for settin
Door or tailgate bumper
p/n: 33-1228-71
Bumper pads, door or tailgate. Twin retainer style. Three eighths (3/8) inch by seven eighths (7/8) inch by one half (1/2) inch high.
Filler and cushion strip
p/n: 70-1237-48
Filler and cushion strip, many applications. Five thirty seconds (5/32) inch by one and five eighths (1-5/8) inch.
Hood Bumper
p/n: 70-1252-42
Bumper, hood to cowl weatherstrip, five sixteenths (5/16) inch high. For three sixteenths (3/16) inch high see our #70-1250-42.
Filler and cushion strip
p/n: 70-1236-48
Filler and cushion strip, many applications. One sixteenth (1/16) inch by one and three eighths (1-3/8) inch.
Sash channel filler 1/32 cork
p/n: 70-1114-57
Filler strip, window glass sash channel. One thirty seconds (1/32) inch thick by 1-1/2 inches wide. For all applications fitting glass to sash channel not requiring weatherlip type of filler. This is the highest quality linen back, rubber cork composition
Sash Channel Filler 1/32 Rubber
p/n: 70-2169-57
Filler strip, window glass sash channel. One thirty seconds (1/32) inch thick by 1-1/2 inches wide. For all applications fitting glass to sash channel not requiring weatherlip type of filler.
Door bumper
p/n: 33-1227-71
Bumper, door edge, twin retainer style, three eighths (3/8) inch wide by seven eighths (7/8) inch long by three eighths (3/8) inch high.
Floor pan plug
p/n: 35-0262-20
Plug, floor pan, rear compartment and body. Up to 12 per car, as required.
Hood bumper
p/n: 70-0294-42
Bumper, hood rest, cap type for adjustable screw, fifteenth sixteenths (15/16) inch, seven sixteenths (7/16) inch thick.
Door Bumper
p/n: 33-1234-71
Bumper, door side. One half (1/2) inch block height. Two (2) or four (4) used per car.
Door weatherstrip fastener
p/n: 50-0198-73
Fastener, door edge weatherstrip, steel. One half (1/2) inch long, thirteen thirty second (13/32) inch diameter head, black finish.
Door Bumper
p/n: 33-1233-71
Bumper, door side. Five eighths (5/8) inch block height. Two (2) or four (4) used per car.
Door Bumper
p/n: 33-1232-71
Bumper, door side. Seven eighths (7/8) inch block height. Two (2) or four (4) used per car.
Door Bumper
p/n: 33-1235-71
Bumper, door side. Three eighths (3/8) inch block height. Two (2) or four (4) used per car.
Hood weatherstrip clip
p/n: 70-0564-42
Fastener, hood to cowl weatherstrip (and other uses), self-retaining steel button, eleven sixteenths (11/16) inch head, for five sixteenths (5/16) inch hole but will fit down to one fourth (1/4) inch hole.
Door weatherstrip fastener
p/n: 70-0553-73
Fastener, auxiliary weatherstrip on door edge. Nylon, self-locking button, for one eighth (1/8) inch hole, thirteen thirty seconds (13/32) inch diameter head.
