This four (4) piece Front Door Vent Window Set contains the main vent window seals and division post seals. All of the pieces were designed from original parts for a precise, factory fit.
This Rear Window Gasket mounts around the full perimeter of the back glass and has properly molded corners. It also has the slot to accommodate the outer edge's decorative molding.
These Front Door Vent Window Weatherstrips are the main seals needed to replace the rubber on your vent windows. They are designed and molded from original parts for superior fitment and seal.
This Windshield Gasket mounts around the full perimeter of the front glass and has properly molded corners for a precise, factory fit. It also has the slot to accommodate the outer edge's decorative molding.
Weatherstrip, door. Installs on inner dog leg.
Channel, side window glass, vertical run. Flexible, felt lined, rubber covered channel. Available 60" lengths.
This Flexible Run Channel helps to eliminate window rattle, provides a smooth sliding surface for glass movement, and works to protect the glass. Stainless steel beaded. Available in sixty (60) inch strips.
Bushings, stabilizer bar to frame. Four (4) piece set.
This Beltline Weatherstrip installs on the left and right doors to wipe the inside and outside of the windows when the glass is lowered. Flexible, pile lined, rubber covered, with a black bead. Available in 3ft pair.
Seals, air vent inlet duct to heater outside.
This Beltline Weatherstrip is sold as a three (3) foot pair. The beltline is used for side window inner and/or outer, front and/or rear doors. Available in a 3ft pair.
This Side Window Weatherstrips can be used for inner and/or outer. The weatherstrip is flexible, pile lined, rubber covered, with black bead. Available in 3ft pairs.
This Peel-N-Stick Trunk Weatherstrip is designed for superior fitment and seal. The seal mounts around the full perimeter of the trunk directly to the body. Easy to install 3M Peel-N-Stick backing provides superior adhesion for reliable performance.
Front vent window division post seal. Fully molded with metal core and attaching tabs.
This Spring Shackle Bushing Set is for the front of the rear leaf spring. One (1) set completes one spring.
This four (4) piece Splash Apron pair is designed from the original part for superior fitment and seal. Installs on the fender splash apron.
This Trunk Weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the trunk lid.
Mount, motor support, front.
Bushing, brake master cylinder. Installs on push rod.
This Transmission Mount is designed from the original part for a correct fitment. Mounts at the rear of manual and automatic transmissions.
This Fender Skirt Edge Seal pair is designed from the original part for superior fitment and seal. For original skirts only this seal fits between fender skirt and rear fender body.
This Spring Shackle Bushing Set is for the rear of the rear leaf spring on car models and the front of the front leaf spring on truck models. Two (2) sets needed per vehicle.
Bumper, front suspension lower arm.
Pads, taillight to body.
Insulator, transmission gear shift column lever.
Insulator, gear shift.
Six (6) piece Spring Clamp Liner Set. The front spring takes eight pieces for both sides and the rear spring takes four pieces for both sides.
This Splash Apron mounts between the front fender splash apron and the front fender. The seal is an exact reproduction of the original Ford part. Sold as a seventy-two (72) inch strip.
Bumper, front suspension upper arm. Three eighths (3/8) inch by three fourths (3/4) inch bolt, twenty four (24) threads.
Bumpers, top of cowl to hood.
This Hood to Cowl Weatherstrip is designed from the original part for superior fitment and seal. An reproduction using dense rubber extrusion and screw fasteners.
Pad, brake and clutch pedal. Replacement type.
Seal, garnish molding to dash rubber. Eighty six (86) inches long. Replaces factory #B9A-7003127.
Gaskets, back-up light housing to body.
This Hood to Cowl Weatherstrip is used to reduce noise from the cowl top ventilator grille. These U-Shaped stripes are designed for a superior fitment and seal.
Pads, outside door handle. Front only. Four (4) piece set.
Pad, parking brake pedal. Slip over type.
This Window Sash Channel Weatherstrip is designed from the original part for superior fitment and seal. Thirty four and three-fourths (34-3/4") inch long EPDM extrusion that goes between glass and metal sash lift channel. One (1) roll required per window.
Pad, brake and clutch pedal. Slip over type.
Bumper, rear spring and axle. 1957-59: Full size Fords: Five (5) required per car (1 in center, 2 each side).
Insulator, front coil spring.
Pad, front fender mount antenna.
Gaskets, taillight lens to housing.
Grommet, main wiring loom through firewall.
Gaskets, back-up light lens.
Gaskets, back-up light to housing.
Grommet, overdrive pull cable.
Grommet, antenna lead-in. For front mount type.
This Rear Spring Pad is used as a spring insert silencer. The leaf spring insulator installs between the leaves.