Body Mounting Pad
p/n: 70-1749-48
This Body Mounting Pad is fully molded rubber with a metal core and locating collar. These frame pads are installed between the frame and the floor pans.
Door Handle Gasket Set
p/n: 70-0925-69
This Door Handle Gasket Set is designed from the original part for superior fitment and seal. This six (6) piece gasket set will do two (2) doors.
Lower Rear Engine Mount
p/n: 20-0584-11
This Lower Rear Engine Mount is designed from original part for correct fitment and function. Made of a quality dense rubber for durability and proper engine vibration isolation. Two (2) required per truck.
Body Mount Isolator Pad
p/n: 70-0929-48
Body Mount Isolator Pad - Rubber with metal core and locating collar as original part. Part dimensions = Two and three sixteenths inch (2 3/16") square by one inch (1") overall height with thirteen sixteenths inch (13/16") inside bolt diameter. Does not include any fastener hardware.
Upper Radiator Filler
p/n: 70-2784-45
This single piece Upper Radiator Filler is designed from the original part for superior fitment and function. This upper radiator to core support filler piece is die cut from quality masticated rubber to authentic original dimensions.
Metal Sleeved Grommet
p/n: 70-0203-41
Flanged rubber grommet with metal sleeve bushing. Used as part of the accelerator relay lever. Also used from 1959-61 on all Cadillac models as a bushing for the windshield wiper relay lever adaptor.
Rear Leaf Spring Insulator
p/n: 70-0980-32
This Rear Leaf Spring Insulator is an exact replacement for the upper and lower spring pad. Two and one half (2-1/2) inches wide, with cloth reinforcement. Four (4) used per car.
Vent Window Division Bar Weatherstrips
p/n: 20-0709-56
This Front Vent Window Division Bar / Post Weatherstrip pair is designed from the original part for superior fitment and seal. This piece mounts with rivets on the vertical division bar and seals as the vent window glass closes against it.
Body Bolt Cushion
p/n: 27-0079-48
Pad, body bolt insulator. Metal core & locating collar covered with rubber. Number used varies per car. Two inch (2") square by seven eights inch (7/8") locating collar outside diameter by five eighths (5/8") locating collar inside hole diameter. Five eig
Front Engine Mount
p/n: 20-0594-11
This Front Engine Mount is designed from original part for correct fitment and function. Rubber coated over a metal core for durability and proper engine vibration isolation.
Window Locking Strip - Black
p/n: 70-2195-52
This extruded Locking Strip is used to retain windshield gaskets in pickups and vans. Designed from the original part for superior fitment, finish and function. Available in 16ft lengths.
Brake and Clutch Pedal Pads
p/n: 70-3003-22
This reproduction Clutch and Brake Pedal Pad pair slips over the full perimeter of the brake pedal for a precise, factory fit. A square style direct fit reproduction to replace worn original pedal pads. Manufactured in black rubber.
Brake and Clutch Pedal Pad
p/n: 40-0287-22
Pads, brake and clutch pedal. Length: 3.625 inches. Width: 2.0 inches.
Fender Welting
p/n: 20-1591-44
This black Fender Welting is designed from the original part for superior fitment and seal. This welting material fits between the fenders and the vehicle body. Eight (8) foot length.
Hood Bumper Set
p/n: 20-0683-42
This six (6) piece Hood Bumper set is designed from the original parts for superior fitment and function. The set fits Ford F-Series Trucks.
Clutch or Brake Pedal Pad
p/n: 60-0467-22
This reproduction Clutch or Brake Pedal Pad pair slips over the full perimeter of the pedal for a precise, factory fit. A perfect reproduction to replace worn original pedal pads. Manufactured in quality black rubber.
Splash Apron / A-Arm Dust Shield
p/n: 70-3066-45
This two (2) piece Splash Apron / A-Arm Dust Shield Filler set is designed from the original part for superior fitment and seal. Filler pieces are die cut from quality masticated rubber to authentic original dimensions. Pieces fit over suspension a-arms and inside front inner fenders.
Spring Shackle Bushing Set
p/n: 20-1834-32
This Spring Shackle Bushing Set is for the rear of the rear leaf spring on car models and the front of the front leaf spring on truck models. Two (2) sets needed per vehicle.
Firewall Grommet
p/n: 70-1914-20
This Firewall Grommet is used for running the heater control cabled wiring harness through the firewall. Designed from the original part for superior fit and seal.
Firewall Grommet
p/n: 25-0099-20
This Firewall Grommet is used to run accessory wiring through the firewall. Designed from the original part for superior fit and seal.
Steering Column Tube To Floor Gasket
p/n: 20-1531-88
This Steering Column Tube To Floor Gasket is designed from the original part for superior fitment and sealing. This part fits around the steering column to seal the column tube through the body floor pan.
Radiator Mounting Pad Set
p/n: 20-0641-31
This Radiator Mounting Pad Set is designed from the original parts for a factory like appearance and function.
Front Stabilizer Bar End Link Set
p/n: 70-2109-33
A twenty-two (22) piece Front Stabilizer Bar End Link set. Comes complete with fasteners, metal sleeves, metal cup washers and black rubber bushings. One (1) end link set for both sides of stabilizer bar on one (1) car.
Gearshift Boot
p/n: 70-2285-26
Boot, transmission control shift lever. Fully molded out of black rubber instead of original white rubber, though it could be painted like original. For vehicles with Hydra-Matic column shift
Hood Bumper
p/n: 70-3022-42
Bumper, hood to fender. Attaches to the hood with single carrot tab on back side. Four (4) per car.
Brake and Clutch Pedal Pad
p/n: 60-0218-22
Pad, brake and clutch pedal. Length: 3.75 inches. Width: 2.375 inches.
Transmission Mount
p/n: 20-1269-11
This Transmission Mount is designed from the original part for a correct fitment. Mounts at the rear of manual and automatic transmissions.
Steering Column Connecting Rod Seal
p/n: 60-0400-36
Steering column steering connecting rod seal. Power steering models require one (1) per car. Non-power steering models require two (2) per car.
Outer Fender To Inner Fender Gaskets
p/n: 70-4797-45
This Outer Fender To Inner Fender Gasket pair is designed from the original part for superior fitment and seal. Gaskets fit at the top of the left and right front fenders. Gasket pieces are die-cut from quality masticated rubber to authentic original OEM dimensions.
Lower suspension arm dust seal
p/n: 70-0646-32
Seal, lower suspension arm, inner. Four (4) piece set.
Hood to Cowl Weatherstrip
p/n: 70-1446-43
Weatherstrip, hood to cowl seal. Approximately fifty seven (57) inches of extruded rubber.
Clutch and Brake Pedal Pads - Black
p/n: 50-0054-22
This reproduction Clutch and Brake Pedal Pad pair slips over the full perimeter of the pedal for a precise, factory fit. A perfect reproduction to replace worn original pedal pads. Manufactured in quality black rubber.
Fender Skirt Edge Weatherstrip
p/n: 20-1317-44
This Fender Skirt Edge Weatherstrip pair is designed from the original part for superior fitment, finish, and seal. This weatherstrips fits between the rear wheel fender skirt and the rear fender quarter panel.
Fender Skirt Edge Weatherstrips
p/n: 20-0061-44
This Fender Skirt Edge Weatherstrip pair is designed from the original part for superior fitment and seal. This weatherstrip fits between the rear quarter panel wheel opening and the fender skirt.
Trunk Weatherstrip
p/n: 70-0773-84
This Trunk Weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the trunk directly to the body.
Trunk Weatherstrip
p/n: 20-1389-84
This Trunk Weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the trunk lid.
Front Engine Mount
p/n: 20-0018-11
This right or left Front Engine Mount is designed from original for correct fitment and function. Rubber bonded to inner metal core with bolt and mounting holes for durability and proper engine vibration isolation.
Wiper Transmission Gasket
p/n: 60-0593-53
Wiper Transmission Gasket - This is the seal for the wiper motor crank. For two (2) speed wiper motors only. These parts are made of the highest quality and authenticity. Replaces # 4906021.
Tailgate Weatherstrip
p/n: 70-1519-87
Weatherstrip, tailgate opening. Pinchweld finish on body. This tailgate weatherstrip reproduction is designed from the original part for superior fitment and seal.
Hood To Cowl Weatherstrip
p/n: 50-0495-43
This Hood To Cowl Weatherstrip is designed from the original part for superior fitment and seal. This 48” long x 1-1/8” wide weatherstrip provides complete coverage.
Windshield Frame to Cowl Weatherstrip
p/n: 70-3004-42
This Windshield Frame to Cowl Weatherstrip is designed from the original part for superior fitment and seal. This cowl rubber goes in between the windshield frame and cowl. This part also fits the 1952-1971 M38A1 model.
Quarter Window Lower Front Corner Seals
p/n: 20-0024-79
This Quarter Window Lower Front Corner seal pair is designed from the original part for superior fitment and seal. A fully molded reproduction of the original for convertible and hardtop models.
Convertible Roof Rail Weatherstrip T-Bolt Set
p/n: 70-4606-67
These Convertible Top Roof Rail Weatherstrip T-Bolt reproductions are designed from the original part for superior fitment and function. This twenty two (22) t-bolts and twenty two (22) nut set fastens to the convertible top bow weatherstrips.
Hood Bumper Set
p/n: 20-0032-42
This six (6) piece Hood Bumper set is designed from the original parts for superior fitment and function.
Vent division bar weatherstrip
p/n: 20-1478-56
Front vent window division post seal. Fully molded with metal core and attaching tabs.
Brake and Clutch Pedal Pads
p/n: 20-0008-22
Pad, brake and clutch pedal. Slip over type. Automatic transmission and manual brakes.
Suspension arm bumper
p/n: 70-1021-32
Bumper, front or rear suspension, upper. Uses two (2) per car on front suspension, one (1) per car on rear.
Convertible Top Rear Rail Water Deflector
p/n: 20-0028-67
This Convertible Top Rear Rail Water Deflector pair is designed from the original part for superior fitment and seal. For soft folding tops the deflector pair is included in Convertible Roof Rail Weatherstrip sets 20-0027-65 and 20-0139-65.
Transmission Mount Service
p/n: 60-0465-25
Transmission mount. One (1) per car. Revulcanization service only.Length: 5.75 inches.
Spring Shackle Bushing Set
p/n: 20-0035-33
This Spring Shackle Bushing Set is an original style rubber leaf spring bushing used on the front of rear spring. One (1) set is required per spring.
Rigid Run Channels
p/n: 70-0516-58
This Rigid Run Channel pair is zinc plated steel with black cloth inside lining to provide a smooth sliding surface for glass movement. Also works to protect the glass. Fastens in place by small screws or rivets on top and bottom.
Rear Bumper Gravel and Splash Guard Shields
p/n: 70-1279-30
This two (2) piece Rear Bumper Gravel and Splash Guard Shield pair is designed from the original part for superior fitment and seal. Twenty-two (22) inches long per side.
Vent division bar weatherstrip
p/n: 20-0021-56
Front vent window division post seal. Fully molded with metal core and attaching tabs.
Door Glass Rigid Run Channel
p/n: 20-0022-58
A Lower Door Glass Rigid Run Channel designed from the original part for superior fitment and function. Installs on the lock side of the door glass frame at the rear of the front door.
Spring Shackle Bushing Set
p/n: 20-1836-32
This Spring Shackle Bushing Set is for the front of the rear leaf spring. One (1) set completes one spring.
Side Window Sash Channel
p/n: 70-0641-58
This Side Window Sash Channel is the u-shaped steel channel only, no filler. Sold in 4 foot strip, usually sufficient for two (2) windows.
Peel-N-Stick Trunk Weatherstrip
p/n: 20-1389-WT
This Peel-N-Stick Trunk Weatherstrip is designed for superior fitment and seal. The weatherstrip mounts around the full perimeter of the trunk directly to the body. Easy to install 3M Peel-N-Stick backing provides superior adhesion for reliable performance.
Fender Skirt Edge Weatherstrip
p/n: 60-0201-45
This Fender Skirt Edge Weatherstrip pair is designed from the original part for superior fitment and seal. This weatherstrips fits between the removable fender skirt and the rear fender quarter panel.
Rear Grill to Body Seal
p/n: 70-3124-31
This Rear Grill to Body Seal is designed from the original part for superior fitment and seal. This seal mounts on the top edge of REAR grill above the rear bumper.