This kit includes the major weatherstrip components and some other essential parts needed for the body of your restoration project.
This front door vent window weatherstrip kit is a four (4) piece set that contains the main vent window seals and division post seals. All of the pieces were designed from original parts for a precise, factory fit.
This rear window gasket mounts around the full perimeter of the back glass and has properly molded corners for a precise, factory fit.
Rear door edge weatherstrip (6 window 4dr hardtop) This part is the primary door to body weatherstrip. Includes eight (8) clips. Note: this is for 6 window 4dr hardtops (vehicles with rear quarter windows).
Door edge weatherstrip with molded ends. This part is the primary door to body weatherstrip. Includes six (6) clips for easy installation. Made of top quality rubber.
Weatherstrip, fixed quarter window. Fully molded like original #4813454-5.
This windshield gasket mounts around the full perimeter of the front glass and has properly molded corners for a precise, factory fit.
Hardtop roof rail weatherstrip. This part fits on the roof of the vehicle and seals the side window when the window is fully raised. Note: Also purchase part #70-1762-73 sold separately.
Bearing support bracket assembly, drive shaft center bearing. Revulcanization service only. .
These front door vent window weatherstrips are the main seals needed to replace the rubber on your vent windows. They are designed and molded from original parts for superior fitment and seal.
Filler, splash apron. Die cut masticated rubber to authentic original dimensions. Includes all factory style holes required for installation.
Gutter, windshield lower corner, left and right. Rubber with metal core as original. Seven and three quarters long (7-3/4").Length: 7.75 inches.
Seal, fenderskirt edge, exact copy, trim notch for skirt lock at installation. Compare sketch with your original to be sure. Two (2), five (5) foot strips.
Weatherstrip, hood to cowl. Correct rubber cross section extrusion. Uses our part numbers #70-1250-42, #70-1251-42 & 70-1252-42 (sold separately) to adjust hood.
Bumper, rear spring axle impact. Located on frame rail. Rubber only, does not include metal retaining clips or bolts.Width: 1.9375 inches. Height: 2.
Deflector, beneath vent frame.Length: 5.75 inches. Width: 1.0 inches.
Pad, front coil spring insulator cushion. Fully molded, mounts at top of front coil springs.
Seal, cowl-to-fender. Die cut masticated rubber to authentic original dimensions. Includes all factory holes required for installation.
Weatherstrip, front door outer beltline "scraper seal" type. Pair of 25" long strips. For models with chrome trim on doors. Plastic guides not included.
Weatherstrip, outer beltline. For use on front, rear, and quarter windows without a chrome reveal molding at the window beltline. Available in a 3ft pair and 6ft piece.
Rear door lock pillar seal. This part seals the bottom of the rear side window, and may also be known as a door jamb seal. Fully molded authentic rubber construction with metal core. Includes twelve (12) clips for easy installation. Note:
Rigid, rubber covered weatherstrip with flock lining and one fourth (1/4) inch chrome edge. Available in a 6ft piece.
Weatherstrip, vertical on lock pillar.Width: .6875 inches. Height: 1.0 inches.
Kit, front stabilizer bar link assembly replacement. Twenty-two (22) piece set. One (1) kit for both sides of one (1) car. Hex head bolt. 5/16"-18nc x 6-15/16" lg. Comes with metal sleeve, metal cup washers and rubber grommets.
Bumper, upper division post w/metal core.Width: 1.75 inches. Height: .50 inches.
Front vent window division post seal. Eleven and one half inches (11.5") and one half inch high. Fully molded with metal core and attaching tabs.
This trunk weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the trunk directly to the body. Easy to install 3M Peel-N-Stick backing provides superior adhesion for reliable performance.
This Side Window Vertical Leading Edge Weatherstrip pair is designed from the original part for superior fitment and seal. This part attaches to the vertical edge of the rear side windows when the rear side windows are fully raised.
Insulator, rear coil spring.
Seal, front door hinge pillar at beltline. Top quality molded rubber.Length: 1.625 inches. Width: .50 inches.
This trunk weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the trunk directly to the body.
Filler, radiator to support seal. Die cut masticated rubber to authentic original dimensions. Includes all factory style holes required for installation.
Bumper, front or rear suspension, upper. Uses two (2) per car on front suspension, one (1) per car on rear.
Radiator mounting pad, insulator. Up to four (4) used per car.Length: 6.0 inches.
Filler, auxiliary splash apron. Fits below sway bar. Two (2) piece set. Die cut masticated rubber.
Flanged rubber grommet with metal sleeve bushing. Used as part of the accelerator relay lever. Also used from 1959-61 on all Cadillac models as a bushing for the windshield wiper relay lever adaptor.
Body Mount Isolator Pad - Rubber with metal core and locating collar as original part. Part dimensions = Two and three sixteenths inch (2 3/16") square by one inch (1") overall height with thirteen sixteenths inch (13/16") inside bolt diameter. Does not include any fastener hardware.
Gasket, door handle. Six (6) piece set includes rubber washer for handle button for two (2) handles.
Taillight lens gasket in fin
Gasket, backup lamp lens.
Gasket, Parking and signal lamp lens.
Gasket, taillight lens.
Cover, battery clamp. Control unsightly sulfate buildup. Help protect the nearby metal and finish. Good copy from original part.Length: 3.5 inches.
Filler, headlight bucket to fender. Two (2) piece set. Die cut masticated rubber.
Bumper, fender to hood. Correct detail with ridges as original. Four (4) required per car.Length: 1.3125 inches.
Front door lock pillar seal. This part seals the bottom of the rear side window, and may also be known as a door jamb seal. Fully molded authentic rubber construction with metal core. Includes eight (8) clips for easy installation. Note: o
Guide plate, plastic, attaches to various outer scraper weatherstrips.
Bumper, hood front aligning. Correct design with proper screw thread.Height: 2.50 inches.
Grommet, dimmer switch for carpet application.
Masticated sheet. Three thirty seconds (3/32) inch thick rubber sheet containing random milled cotton cord reinforcement for front end splash aprons, etc. This product is a four (4) foot wide roll, and will only be sold in four (4) square foot multiples