This kit includes the major weatherstrip components and some other essential parts needed for the body of your restoration project.
This Convertible Roof Rail Weatherstrip Set fits on the folding roof of the vehicle and seals the side window when the window is fully raised.
This Front Motor Mount revulcanizing service replaces the rubber in your original Motor Mounts to make them like new again. The process is designed for the original factory mounts only. Send in cores and allow three weeks for service.
This four (4) piece Front Door Vent Window Set contains the main vent window seals and division post seals. All of the pieces were designed from original parts for a precise, factory fit.
Door edge weatherstrip with molded ends. This part is the primary seal which seals the door to body. Includes four (4) pins and twenty-six (26) sockets for easy installation.
Bearing support bracket assembly, drive shaft center bearing. Revulcanization service only. .
These Front Door Vent Window Weatherstrips are the main seals needed to replace the rubber on your vent windows. They are designed and molded from original parts for superior fitment and seal.
This Windshield Gasket mounts around the full perimeter of the front glass and has properly molded corners for a precise, factory fit.
Insulator, (cushion) motor support, rear at transmission. Revulcanization service only.
This 1957-1964 Cadillac Master Parts List - Two (2) Volume set licensed Detroit Iron reprint provides the most comprehensive repair information in paper format. This OEM PARTS manual reproduction provides detailed original part numbers, part assembly diagrams / illustrations and part textual details for all vehicle subsystems.
This fourteen (14) piece Splash Apron / A-Arm Dust Shield Filler set is designed from the original part for superior fitment and seal. Filler pieces are die cut from quality masticated rubber to authentic original dimensions. Pieces fit over suspension a-arms and inside front inner fenders.
Convertible Hinge Pillar Weatherstrip - Attaches to the body and seals between the A-pillar post and the front section of the door or vent window frame when the door is closed. Includes two (2) pins.
Bumper, motor yaw control. Two (2) per car on 2nd cross member. Revulcanization service only.Length: 3.0 inches.
Gutter, windshield lower corner, left and right. Rubber with metal core as original. Seven and three quarters long (7-3/4").Length: 7.75 inches.
This Beltline Weatherstrip is thick pile lined without chrome bead. Available in 4ft pairs.
Seal, fenderskirt edge, exact copy, trim notch for skirt lock at installation. Compare sketch with your original to be sure. Two (2), five (5) foot strips.
Weatherstrip, hood to cowl. Correct rubber cross section extrusion. Uses our part numbers #70-1250-42, #70-1251-42 & 70-1252-42 (sold separately) to adjust hood.
Bumper, rear spring axle impact. Located on frame rail. Rubber only, does not include metal retaining clips or bolts.Width: 1.9375 inches. Height: 2.
These Beltline Weatherstrips (sometimes called "scraper seal") come in a three (3) foot pair. For use on front, rear, and quarter windows without a chrome reveal molding at the window beltline. Available in 3ft pair.
This Outer Beltline Weatherstrip is fully molded with EPDM rubber over a corrosion resistant brass metal core. These window scrapers are for models with the chrome strip on the door. Designed like original with attaching tabs.
Pad, front coil spring insulator cushion. Fully molded, mounts at top of front coil springs.
Door lock pillar seal. This part seals the bottom of the rear side window, and may also be known as a door jamb seal.
This run channel upper bumper is manufactured as original with a brass metal core and molded for a precise, factory fit. The seal is installed at the top of the front door vent window frame on the division post.
This GM Licensed Detroit Iron CD provides the most comprehensive set of digital Cadillac Factory parts manuals. The factory manuals on this CD were professionally scanned from the original service and parts manuals.
This Body / Cowl to Fender Seals pair is designed from the original part for superior fitment and function. Filler seal pieces are die cut from quality masticated rubber to authentic original dimensions.
This Beltline Weatherstrip comes in a six (6) foot length for the outer beltline (sometimes called "scraper seal"). For use on front, rear, and quarter windows without a chrome reveal molding at the window beltline. Available in 6ft lengths.
This Beltline Weatherstrip Channel is a five (5) foot length of rigid channel with a flocked rubber lip and a flat stainless bead. Can be used as the inner beltline weatherstrip on front doors, rear doors and quarter windows.
Side window vertical leading edge weatherstrip.
Kit, front stabilizer bar link assembly replacement. Twenty-two (22) piece set. One (1) kit for both sides of one (1) car. Hex head bolt. 5/16"-18nc x 6-15/16" lg. Comes with metal sleeve, metal cup washers and rubber grommets.
Front vent window division post seal. Eleven and one half inches (11.5") and one half inch high. Fully molded with metal core and attaching tabs.
This Peel-N-Stick Trunk Weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the trunk directly to the body.
This hinge seal is installed on the front door hinge pillar at the beltline. These seals are sold as a pair for the left and right side.
This single piece Radiator Upper Support Filler is designed from the original part for superior fitment and function. Filler piece is die cut from quality masticated rubber to authentic original dimensions. Fits at radiator to radiator upper support.
Bumper, front or rear suspension, upper. Uses two (2) per car on front suspension, one (1) per car on rear.
This Trunk Weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the trunk directly to the body.
Radiator mounting pad, insulator. Up to four (4) used per car.Length: 6.0 inches.
This four (4) piece Taillight Lens Gasket set is designed from the original part for superior fitment and seal. The larger gaskets are for the outer lens. The smaller circular gaskets are for the small glass dome shaped lens that sits inside the housing.
This Directional Turn Signal or Fog Light Lens Gasket pair is designed from the original part for superior fitment and seal. This reproduction gasket fits between the Directional Signal / Fog Light Lens and the Directional Signal / Fog Light Housing or Bezel.
This Auxiliary / Frame Dust Shield pair is designed from the original part for superior fitment and function. The two (2) shield pieces are die cut from quality masticated rubber to authentic original dimensions. These shield pieces fit under the vehicle sway bar, near the frame.
Flanged rubber grommet with metal sleeve bushing. Used as part of the accelerator relay lever. Also used from 1959-61 on all Cadillac models as a bushing for the windshield wiper relay lever adaptor.
Body Mount Isolator Pad - Rubber with metal core and locating collar as original part. Part dimensions = Two and three sixteenths inch (2 3/16") square by one inch (1") overall height with thirteen sixteenths inch (13/16") inside bolt diameter. Does not include any fastener hardware.
This Door Handle Gasket Set is designed from the original part for superior fitment and seal. This six (6) piece gasket set will do two (2) doors.
This Taillight Lens Gasket pair is designed from the original part for superior fitment and seal. This reproduction gasket fits between the taillight lens & taillight housing in fin.
Cover, battery clamp. Control unsightly sulfate buildup. Help protect the nearby metal and finish. Good copy from original part.Length: 3.5 inches.
Cover, rocker panel inner dust shield. Fully molded with proper attaching teeth and flap.
This two (2) piece Headlight Bucket to Fender Seal pair is designed from the original part for superior fitment and seal. Die cut from original style masticated rubber for a like factory fit.
Bumper, fender to hood. Correct detail with ridges as original. Four (4) required per car.Length: 1.3125 inches.
Guide plate, plastic, attaches to various outer scraper weatherstrips.
Bumper, hood front aligning. Correct design with proper screw thread.Height: 2.50 inches.
Masticated sheet. Three thirty seconds (3/32) inch thick rubber sheet containing random milled cotton cord reinforcement for front end splash aprons, etc. This product is a four (4) foot wide roll, and will only be sold in four (4) square foot multiples