Search Results
Body Weatherstrip Kit
p/n: 90-3171-90
This kit includes the major weatherstrip components and some other essential parts needed for the body of your restoration project.
Front Motor Mount Revulcanizing Service
p/n: 70-0548-11
This Front Motor Mount revulcanizing service replaces the rubber in your original Motor Mounts to make them like new again. The process is designed for the original factory mounts only. Send in cores and allow three weeks for service.
Rear Window Gasket
p/n: 70-0995-81
This rear window gasket mounts around the full perimeter of the back glass and has properly molded corners for a precise, factory fit.
Windshield Gasket
p/n: 70-1286-50
This Windshield Gasket mounts around the full perimeter of the front glass and has properly molded corners for a precise, factory fit.
Front Door Vent Window Set
p/n: 90-0429-90
This four (4) piece Front Door Vent Window Set contains the main vent window seals and division post seals. All of the pieces were designed from original parts for a precise, factory fit.
Rear Door Weatherstrip
p/n: 70-0901-72
Rear door edge weatherstrip (6 window 4dr hardtop) This part is the primary door to body weatherstrip. Includes eight (8) clips. Note: this is for 6 window 4dr hardtops (vehicles with rear quarter windows).
Quarter window weatherstrip
p/n: 70-1504-77
Weatherstrip, fixed quarter window. Fully molded like original #4813454-5.
Hardtop roof rail weatherstrip
p/n: 70-0960-68
Hardtop roof rail weatherstrip (6 window 4dr hardtop). This part fits on the roof of the vehicle and seals the side window when the window is fully raised. Includes four (4) clips. Note: this is for 6 window 4dr hardtops only (vehicles with
Prop shaft support service
p/n: 70-0903-27
Support, prop shaft center bearing. Revulcanization service only.
Front Door Vent Window Weatherstrips
p/n: 38-0096-55
These Front Door Vent Window Weatherstrips are the main seals needed to replace the rubber on your vent windows. They are designed and molded from original parts for superior fitment and seal.
Motor mount service
p/n: 70-0708-11
Insulator, (cushion) motor support, rear at transmission. Revulcanization service only.
Cadillac Master Parts List 1957 - 1964 (Reprint)
p/n: 07-1443-07
This 1957-1964 Cadillac Master Parts List - Two (2) Volume set licensed Detroit Iron reprint provides the most comprehensive repair information in paper format. This OEM PARTS manual reproduction provides detailed original part numbers, part assembly diagrams / illustrations and part textual details for all vehicle subsystems.
Front Door Weatherstrip
p/n: 70-0824-72
Door edge weatherstrip with molded ends. This part is the primary door to body weatherstrip. Includes six (6) clips for easy installation. Made of top quality rubber.
Motor yaw control arm service
p/n: 70-0778-11
Bumper, motor yaw control. Two (2) per car on 2nd cross member. Revulcanization service only.Length: 3.0 inches.
Splash Apron / A-Arm Dust Shield Set
p/n: 70-2496-45
This ten (10) piece Splash Apron / A-Arm Dust Shield set is designed from the original part for superior fitment and seal. Filler pieces are die cut from quality masticated rubber to authentic original dimensions. Pieces fit over suspension a-arms and inside front inner fenders.
Beltline Weatherstrip
p/n: 70-0961-60
This Beltline Weatherstrip is thick pile lined without chrome bead. Available in 4ft pairs.
Fenderskirt Edge Seal
p/n: 70-0154-45
Seal, fenderskirt edge, exact copy, trim notch for skirt lock at installation. Compare sketch with your original to be sure. Two (2), five (5) foot strips.
Hood to cowl weatherstrip
p/n: 70-1049-43
Weatherstrip, hood to cowl. Uses our part #70-1250-42, #70-1251-42 & 70-1252-42 (sold separately) to adjust hood.
Headlight & Cornering Light Filler Seal Set
p/n: 70-2788-14
This six (6) piece Headlight & Cornering Light Filler Seal Set is designed from the original part for superior fitment and seal. These pieces fit behind the cornering lights.
Beltline Weatherstrips
p/n: 70-1121-61
These Beltline Weatherstrips (sometimes called "scraper seal") come in a three (3) foot pair. For use on front, rear, and quarter windows without a chrome reveal molding at the window beltline. Available in 3ft pair.
Front coil spring pad
p/n: 70-2302-35
Pad, front coil spring insulator cushion. Fully molded, mounts at top of front coil springs.
1935-1974 Cadillac Factory Parts Manual, CD
p/n: 07-1346-07
This GM Licensed Detroit Iron CD provides the most comprehensive set of digital Cadillac Factory parts manuals. The factory manuals on this CD were professionally scanned from the original service and parts manuals.
Outer Beltline Weatherstrip
p/n: 70-0802-61
This Outer Beltline Weatherstrip is fully molded with EPDM rubber over a corrosion resistant brass metal core. These window scrapers are for models with the chrome strip on the door. Designed like original with attaching tabs.
Outer Beltline Weatherstrip
p/n: 70-0803-61
This Outer Beltline Weatherstrip is fully molded with EPDM rubber over a corrosion resistant brass metal core. These window scrapers are for models with the chrome strip on the door. Designed like original with attaching tabs.
Beltline Weatherstrip
p/n: 70-1120-61
This Beltline Weatherstrip comes in a six (6) foot length for the outer beltline (sometimes called "scraper seal"). For use on front, rear, and quarter windows without a chrome reveal molding at the window beltline. Available in 6ft lengths.
Rear Door Pillar Filler
p/n: 70-0837-79
This Rear Door Pillar Filler pair is designed from the original part for superior fitment and sealing. This left and right weatherstrip filler mounts at the bottom of the rear side window, lower leading edge to seal the rear quarter window. Also known as a door jamb seal.
Beltline Weatherstrip Channel
p/n: 70-0651-58
This Beltline Weatherstrip Channel is a five (5) foot length of rigid channel with a flocked rubber lip and a flat stainless bead. Can be used as the inner beltline weatherstrip on front doors, rear doors and quarter windows.
Door weatherstrip
p/n: 70-1762-73
Weatherstrip, vertical on lock pillar.Width: .6875 inches. Height: 1.0 inches.
Front Stabilizer Bar End Link Kit
p/n: 70-2110-33
Kit, front stabilizer bar link assembly replacement. Twenty-two (22) piece set. One (1) kit for both sides of one (1) car. Hex head bolt. 5/16"-18nc x 6-15/16" lg. Comes with metal sleeve, metal cup washers and rubber grommets.
Rigid Run Channel
p/n: 70-0752-58
Sliding glass window unbeaded u-channel secures sliding glass and eliminates rattle. Available in 6ft lengths.
Vent division bar weatherstrip
p/n: 70-0859-56
Front vent window division post seal. Fully molded with metal core and attaching tabs.
Side Window Vertical Leading Edge
p/n: 70-0806-80
This Side Window Vertical Leading Edge Weatherstrip pair is designed from the original part for superior fitment and seal. This part attaches to the vertical edge of the rear side windows when the rear side windows are fully raised.
Peel-N-Stick Trunk Weatherstrip
p/n: 70-0773-WT
This Peel-N-Stick Trunk Weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the trunk directly to the body.
Body / Cowl to Fender Seals
p/n: 70-2790-43
This Body / Cowl to Fender Seals pair is designed from the original part for superior fitment and function. Filler seal pieces are die cut from quality masticated rubber to authentic original dimensions.
Trunk Weatherstrip
p/n: 70-0773-84
This Trunk Weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the trunk directly to the body.
Hood To Fan Shroud Seal
p/n: 70-2789-43
This Hood To Fan Shroud Seal is designed from the original part for superior fitment and function. Attaches to bottom side of hood. This seal piece is die cut from quality masticated black rubber to authentic original dimensions.
Radiator mounting pad
p/n: 70-0963-31
Radiator mounting pad, insulator. Up to four (4) used per car.Length: 6.0 inches.
Cornering Light Lens Gaskets
p/n: 70-3162-16
This Cornering Light Lens Gasket pair is designed from the original part for superior fitment and seal. These quality reproduction gaskets fit between the cornering light lens and the cornering light housing or bezel.
Auxiliary / Frame Dust Shield
p/n: 70-3084-45
This Auxiliary / Frame Dust Shield pair is designed from the original part for superior fitment and function. The two (2) shield pieces are die cut from quality masticated rubber to authentic original dimensions. These shield pieces fit under the vehicle sway bar, near the frame.
Metal sleeved grommet
p/n: 70-0203-41
Flanged rubber grommet with metal sleeve bushing. Used as part of the accelerator relay lever. Also used from 1959-61 on all Cadillac models as a bushing for the windshield wiper relay lever adaptor.
Body Mount Isolator Pad
p/n: 70-0929-48
Body Mount Isolator Pad - Rubber with metal core and locating collar as original part. Part dimensions = Two and three sixteenths inch (2 3/16") square by one inch (1") overall height with thirteen sixteenths inch (13/16") inside bolt diameter. Does not include any fastener hardware.
Door Handle Gasket Set
p/n: 70-0733-69
This Door Handle Gasket Set is designed from the original part for superior fitment and seal. This six (6) piece gasket set will do two (2) doors.
Battery Clamp Cover
p/n: 70-0095-21
This black rubber Battery Clamp Cover helps to protect the nearby metal and finish. Good copy from an original part. Length: 3-1/2" inches.
AC condenser mount
p/n: 70-0964-31
Mount, air conditioning condenser. Four (4) used per car.Length: 1.0 inches. Width: .75 inches.
Directional & Parking Light Lens Gaskets
p/n: 70-3230-16
This Turn Signal and Parking Light Lens Gasket pair is designed from the original part for superior fitment and seal. This reproduction gasket fits between the Signal / Parking Light Lens and the Signal / Parking Light Housing or Bezel.
License Plate Light Lens Gaskets
p/n: 70-3160-16
This License Plate Light Lens Gasket pair is designed from the original part for superior fitment and seal. This reproduction gasket fits between the License Plate Light Lens and the License Plate Light Housing or Bezel.
Hood bumper
p/n: 70-0770-42
Bumper, fender to hood. Correct detail with ridges as original. Four (4) required per car.Length: 1.3125 inches.
Front Door Lock Pillar Filler
p/n: 70-0834-79
This Front Door Lock Pillar Filler pair is designed from the original part for superior fitment and sealing. This left and right weatherstrip filler seals the bottom at the front of the rear side window. Also known as a door jamb seal.
Plastic guide plate
p/n: 50-0384-62
Guide plate, plastic, attaches to various outer scraper weatherstrips.