Firewall to Hood Weatherstrip - Cowl Lacing
p/n: 20-1457-42
This Firewall to Hood Weatherstrip is designed from the original part for superior fitment and seal. An exact reproduction of the original profile. This single piece cowl lacing seal mounts at the rear of the engine bay to seal between the hood and vehicle body cowl / firewall.
Body Mount Isolator Pad
p/n: 70-0929-48
Body Mount Isolator Pad - Rubber with metal core and locating collar as original part. Part dimensions = Two and three sixteenths inch (2 3/16") square by one inch (1") overall height with thirteen sixteenths inch (13/16") inside bolt diameter. Does not include any fastener hardware.
Taillight Lens Gaskets - Inner and Outer
p/n: 20-1410-15
This four (4) piece Taillight Lens Gasket set is designed from the original part for superior fitment and seal. These inner and outer reproduction gaskets fit between taillight lens and taillight housing bezel.
Air Vent Gasket Set
p/n: 70-4472-31
This Air Vent Gasket set is designed from original parts for superior fitment and sealing. These quality manufactured gaskets fit to seal the two (2) conditioned air assemblies for interior comfort.
Front Fender Splash Shield Set
p/n: 20-2762-45
This six (6) piece Front Fender Splash Shield Set is designed from the original part for superior fitment and seal. Includes attaching staples.
Metal Sleeved Grommet
p/n: 70-0203-41
Flanged rubber grommet with metal sleeve bushing. Used as part of the accelerator relay lever. Also used from 1959-61 on all Cadillac models as a bushing for the windshield wiper relay lever adaptor.
Front Fender Inner Seal Set
p/n: 70-3318-45
This four (4) piece Front Fender Inner Seal set is designed from the original part for superior fitment and function. The seal pieces are die cut from quality masticated rubber to authentic original dimensions.
Hood to Fender Bumper
p/n: 70-2046-42
This Hood to Fender Bumper pair is a quality reproduction of the original factory part. These rubber bumpers attach to the front fender to support / cushion the hood closure.
Rear spring bushing
p/n: 20-0661-32
Bushing, rear spring front and rear. Useage: 1964-66: F250 4x2's- 4 required 1966: F250 4x4's and all 350's- 2 required 1966-69- Bronco
Rear Leaf Spring Insulator
p/n: 70-0980-32
This Rear Leaf Spring Insulator is an exact replacement for the upper and lower spring pad. Two and one half (2-1/2) inches wide, with cloth reinforcement. Four (4) used per car.
Trunk Decklid Weatherstrip
p/n: 20-2858-84
This Trunk Deckid Weatherstrip is designed from the original part for superior fitment and seal. The weatherstrip mounts around the full perimeter of the trunk lid.
Door Bumper
p/n: 70-3035-71
This Door Bumper is designed from the original part and attaches to door with single screw. Typically requires two (2) or four (4) bumpers per vehicle depending on the vehicles year of manufacture.
Radiator Top Seal
p/n: 20-0181-31
Seal, top of radiator support to hood air deflector. Fifty (50) inches long. For the following engines: 240, 289, 352, 390, 427, or 428.
Hood to Cowl Weatherstrip
p/n: 20-1311-42
Kit, cowl lacing. his seal mounts at the rear of the engine bay to seal between the hood and vehicle body cowl.
Window Locking Strip - Black
p/n: 70-2195-52
This extruded Locking Strip is used to retain windshield gaskets in pickups and vans. Designed from the original part for superior fitment, finish and function. Available in 16ft lengths.
Brake and Clutch Pedal Pads
p/n: 70-3003-22
This reproduction Clutch and Brake Pedal Pad pair slips over the full perimeter of the brake pedal for a precise, factory fit. A square style direct fit reproduction to replace worn original pedal pads. Manufactured in black rubber.
Air Deflector - At Radiator Core Support
p/n: 20-0193-31
This Air Deflector piece is designed from the original part for superior fitment and seal. Piece is die cut from quality masticated rubber to authentic original dimensions. This piece fits at the bottom of radiator core support to frame. Used on V8 models.
Fender Welting
p/n: 20-1591-44
This black Fender Welting is designed from the original part for superior fitment and seal. This welting material fits between the fenders and the vehicle body. Eight (8) foot length.
Hood Bumper Set
p/n: 20-0683-42
This six (6) piece Hood Bumper set is designed from the original parts for superior fitment and function. The set fits Ford F-Series Trucks.
Hood Bumper Set
p/n: 20-0684-42
This six (6) piece Hood Bumper set is designed from the original parts for superior fitment and function. The set fits Ford F-Series Trucks.
Clutch or Brake Pedal Pad
p/n: 60-0467-22
This reproduction Clutch or Brake Pedal Pad pair slips over the full perimeter of the pedal for a precise, factory fit. A perfect reproduction to replace worn original pedal pads. Manufactured in quality black rubber.
Splash Apron / A-Arm Dust Shield
p/n: 70-3216-45
This two (2) piece Splash Apron / A-Arm Dust Shield Filler pair is designed from the original part for superior fitment and seal. Filler pieces are die cut from quality masticated rubber to authentic original dimensions. Pieces fit over suspension a-arms and inside front inner fenders.
Radiator Bracket Cushion
p/n: 70-2014-31
Radiator support bracket, insulator, upper. Two (2) used per car.Length: 6.0 inches.
Radiator bracket cushion
p/n: 70-2015-31
Insulator, radiator support cushion, upper or lower. Fully molded with retaining carrots.
Hood to Cowl Weatherstrip
p/n: 70-3924-43
This Hood to Cowl Weatherstrip has the proper rubber cross section and is made from top quality rubber to ensure durability and seal. Designed from the original part for a superior fitment and seal.
Radiator Mounting Pad
p/n: 70-0963-31
Radiator mounting pad, insulator. Up to four (4) used per car.Length: 6.0 inches.
Door Handle Gasket Set
p/n: 70-3036-69
This Door Handle Gasket Set is designed from the original part for superior fitment and seal. One (1) gasket set will do either front or rear two (2) doors.
Steering Column Tube To Floor Gasket
p/n: 20-1531-88
This Steering Column Tube To Floor Gasket is designed from the original part for superior fitment and sealing. This part fits around the steering column to seal the column tube through the body floor pan.
Vent Window Division Post Weatherstrips
p/n: 20-0710-56
Front Vent Window Division Post seal pair that functions as the back edge of the vent window seal. Fully molded rubber over a metal core and attaching tabs.
Rear Transmission Mount
p/n: 20-0090-25
This Transmission Mount is designed from the original part for superior fitment and function. This rear mount fits between the transmission and the crossmember to locate and retain the rear of the engine / transmission powertrain. Automatic and Manual transmissions.
Hood Bumper
p/n: 70-3022-42
Bumper, hood to fender. Attaches to the hood with single carrot tab on back side. Four (4) per car.
Body / Cowl to Fender Seals
p/n: 70-2790-43
This Body / Cowl to Fender Seals pair is designed from the original part for superior fitment and function. Filler seal pieces are die cut from quality masticated rubber to authentic original dimensions.
Splash Apron / A-Arm Dust Shield Filler
p/n: 70-3484-45
This two (2) piece Splash Apron / A-Arm Dust Shield Filler pair is designed from the original part for superior fitment and seal. Filler pieces are die cut from quality masticated rubber to authentic original dimensions. Left and Right pieces fit over suspension a-arms and inside front inner fenders.
Hood to Cowl Weatherstrip
p/n: 70-4800-43
This Hood To Cowl Weatherstrip is designed from the original part for superior fitment and seal. An exact reproduction of the original profile. This weatherstrip installs at the rear of the engine bay to seal between the hood and vehicle body cowl.
Front Stabilizer Bar End Link Set
p/n: 70-2110-33
A twenty-two (22) piece Front Stabilizer Bar End Link set. Comes complete with fasteners, metal sleeves, metal cup washers and black rubber bushings. One (1) end link set for both sides of stabilizer bar on one (1) car.
Ulta-Mat Quarter Panel Heat and Sound Underlayment
p/n: 70-4784-88
This Ulta-Mat Quarter Panel Heat and Sound Underlayment pair is pre-cut for a direct-fit installation. Underlayment pieces are made from a flexible and lightweight foil facing foam rubber sound and heat insulation material.
Trunk Weatherstrip
p/n: 70-0774-84
This Trunk Weatherstrip is designed from the original part for superior fitment and seal. The weatherstrip mounts around the full perimeter of the trunk directly to the body.
Front Stabilizer Bar End Link Set
p/n: 70-2111-33
A twenty-two (22) piece Front Stabilizer Bar End Link set. Comes complete with fasteners, metal sleeves, metal cup washers and black rubber bushings. One (1) end link set for both sides of stabilizer bar on one (1) car.
Outer Fender To Inner Fender Gaskets
p/n: 70-4797-45
This Outer Fender To Inner Fender Gasket pair is designed from the original part for superior fitment and seal. Gaskets fit at the top of the left and right front fenders. Gasket pieces are die-cut from quality masticated rubber to authentic original OEM dimensions.
Window Gasket Locking Strip - Chrome
p/n: 70-1919-52
This chrome appearing Window Gasket Locking Strip is designed from the original part for superior fitment and seal. Locking strip serves as the front or rear window gasket retainer. Sixteen (16') foot length single piece, one application, for complete coverage.
Rear Leaf Spring Shackle Assembly
p/n: 20-1066-32
This reproduction Rear Leaf Spring Shackle Assembly is complete with shackle bar plates, rubber bushings and lock nuts. For fitting the suspension leaf spring at its rear spring eye to the vehicle body. Two (2) assemblies required per car.
Accelerator Pedal Pad
p/n: 20-1075-40
This Accelerator Pedal Pad is made of top-quality EPDM rubber with a high level of fit and finish. Designed to be a direct fit reproduction.
Front Fender Inner Seals
p/n: 70-2793-45
This Front Fender Inner Seal pair is designed from the original part for superior fitment and function. The seal pieces are die cut from quality masticated rubber to authentic original dimensions. Installation clips are included.
Hood to Cowl Weatherstrip
p/n: 70-1446-43
Weatherstrip, hood to cowl seal. Approximately fifty seven (57) inches of extruded rubber.
Taillight Lens Gaskets
p/n: 70-4049-15
This Taillight Lens Gasket pair, for right and left side, is designed from the original part for superior fitment and seal. These reproduction gaskets fit between taillight lens and taillight housing.
Accelerator Pedal Pad
p/n: 20-0678-40
Pedal, accelerator. Molded rubber design. Trucks (F100-200) after Serial #696,001.
Quarter Window Vertical Leading Edge
p/n: 20-2845-80
This Quarter Window Vertical Leading Edge pair is the vertical piece of weatherstrip that seals between the door glass and the rear quarter window glass when the quarter window is raised and closed.
Floor Shift | Carpet Grommet
p/n: 70-3265-88
This Floor Shift / Carpet Grommet is designed from the original part for superior fitment and seal. This part seals the carpet edge to the floor shift boot. For models without floor console.
Fuel Filler Neck Grommet
p/n: 70-3622-39
This Fuel Filler Neck Grommet is designed from the original part for superior fitment and seal. This grommet fits around the vehicles fuel filler neck between the filler neck and vehicle body.
Firewall Accessory Wiring Grommet
p/n: 27-0100-20
This Firewall Accessory Wiring Grommet is designed from the original part for superior fitment and function.
Side Window Leading Edge Weatherstrips
p/n: 50-0428-80
This Side Window Leading Edge Weatherstrip pair is designed from the original part for superior fitment and seal. This part attaches to the vertical edge of the rear side windows when the rear side windows are fully raised.
Rear Bumper Fillers
p/n: 70-4911-47
This Rear Bumper Filler pair is designed from the original part for a superior fitment level. These fully molded end pieces fit to the left and right bumper ends between the rear bumper and the vehicle body.
Lower Sash Channel Filler, Door Glass
p/n: 20-0240-58
Channel, door window glass lower rubber. Front or rear doors. One (1) pair does two (2) windows.
Fender Skirt Edge Weatherstrips
p/n: 20-0061-44
This Fender Skirt Edge Weatherstrip pair is designed from the original part for superior fitment and seal. This weatherstrip fits between the rear quarter panel wheel opening and the fender skirt.
Body / Cowl to Fender Seals
p/n: 70-3076-43
This Body / Cowl to Fender Seal pair is designed from the original part for superior fitment and function. Filler seal pieces are die cut from quality masticated rubber to authentic original dimensions.
Wiring Grommet Boots
p/n: 70-4712-21
This Wiring Grommet Boot pair is designed from the original part for superior fitment and function. This protective wiring grommet boot can be found below the vehicle's package tray and at the quarter window pillar.
Trunk Weatherstrip
p/n: 70-0773-84
This Trunk Weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the trunk directly to the body.
Peel-N-Stick Trunk Decklid Weatherstrip
p/n: 20-2859-WT
This Peel-N-Stick Trunk Decklid Weatherstrip is designed for superior fitment and seal. The weatherstrip mounts around the full perimeter of the trunk decklid to seal directly to the body. Easy to install 3M Peel-N-Stick backing provides superior adhesion for reliable performance.
Clutch and Brake Pedal Pads
p/n: 60-0242-22
This reproduction Clutch and Brake Pedal Pad pair slips over the full perimeter of the pedal for a precise, factory fit. A perfect reproduction to replace worn original pedal pads. Manufactured in quality black rubber.
Heater Core Housing To Firewall Gasket
p/n: 70-4473-31
This Heater Core Housing To Firewall gasket is designed from original parts for superior fitment and sealing. This quality manufactured gasket fits to seal the heater core housing to the vehicle firewall.
Wiper Transmission Gasket
p/n: 60-0593-53
Wiper Transmission Gasket - This is the seal for the wiper motor crank. For two (2) speed wiper motors only. These parts are made of the highest quality and authenticity. Replaces # 4906021.
Taillight Mounting Pad
p/n: 70-2166-15
Pad, taillight mounting to rear quarter panel. Proper extrusion cross section like original. Two (2) strips twenty-four (24) inch long. Length: 24.0 inches.