Front Door Weatherstrips
p/n: 20-0284-72
This Front Door Weatherstrip pair is designed from the original part for superior fitment and seal. Push-pin type door weatherstrips mount directly to the body to seal against the full perimeter of the doors.
Division Bar Glass Run Channels
p/n: 20-0239-58
This two (2) piece Division Bar Glass Run Channel pair installs between the front of door glass and the back of the vent window.
Rear Bumper Stone Deflector Seal
p/n: 20-0232-47
This Rear Bumper Stone Deflector Seal is designed as an exact reproduction of the original bumper to body seal.
Hood Bumper Set
p/n: 20-0208-42
This eight (8) piece Hood Bumper set is designed from the original parts for superior fitment and function.
Front Lower Control Arm Bumper
p/n: 20-0202-32
This Front Lower Control Arm Bumper is designed from the original part for superior fitment, finish, and function. This suspension bumper mounts to the front lower control arm to prevent metal to metal contact.
Front Fender Apron Dust Shields
p/n: 20-0219-44
This Front Fender Apron Dust Shield pair is designed from the original part for superior fitment and function. Filler shield pieces are die cut from quality masticated rubber to authentic original dimensions.
Hood to Cowl Weatherstrip
p/n: 20-0215-43
This Hood to Cowl Weatherstrip is designed from the original part for superior fitment and seal. An exact reproduction using the correct profile dense rubber extrusion.
Splash Apron / A-Arm Dust Shield Filler
p/n: 70-3691-45
This two (2) piece Splash Apron / A-Arm Dust Shield Filler pair is designed from the original part for superior fitment and seal. Filler pieces are die cut from quality masticated rubber to authentic original dimensions. Left and Right pieces fit over suspension a-arms and inside front inner fenders.
Accelerator pedal pad
p/n: 20-0678-40
Pedal, accelerator. Molded rubber design. Trucks (F100-200) after Serial #696,001.
Radiator top seal
p/n: 20-0181-31
Seal, top of radiator support to hood air deflector. Fifty (50) inches long. For the following engines: 240, 289, 352, 390, 427, or 428.
Brake or Clutch Pedal Pad
p/n: 20-0177-22
Brake or Clutch Pedal Pad - Four (4) inches long by two and three eights (2-3/8) inches long outside to outside measurements.
Front Suspension Bumper
p/n: 20-0080-32
Bumper for front suspension upper arm. Measures three eighths (3/8) inch by sixteen (16) by eleven sixteenths with (11/16) inch bolt thread.
Hood bumper
p/n: 20-0207-42
Bumper, hood on fender. Push-in type. Three fourths (3/4) inch wide. Four (4) piece set.
Hood bumper
p/n: 20-0209-42
Bumper, hood on rear of fender. Rubber button tip only. Two (2) piece set.
Steering Column Lower Flange Insulator
p/n: 20-1532-88
This Steering Column Lower Flange Insulator is designed from the original part for superior fitment and function. This insulator fits around the lower steering column inside the vehicle to prevent metal to metal contact.
Hood Bumper, Adjustable
p/n: 70-2715-42
This Radiator Support to Hood Bumper is a quality replacement for the original factory part. This adjustable bumper attaches to the radiator support to cushion / stop the hood closure. Usually requires two (2) front bumpers each per vehicle.
Radiator shroud seal
p/n: 20-0182-31
Seal, radiator side air deflector. One and five eighths (1-5/8) inch by twelve and one half (12-1/2) inch.
Body Hole Plug
p/n: 20-1041-21
Plug, cowl and floor pan. This body plug covers a sheet metal hole that is one and one seven eighths (1-7/8) inch in diameter.
Door bumper
p/n: 20-0067-71
Bumper, door. Installs on back edge of door. Please check your car for quantities required.Usually two (2) to eight (8) per vehicle.
Glovebox Arm Bumper Stop
p/n: 20-1399-88
Stop, glovebox arm.Ford Truck 1957-64 Stop, glovebox arm. Requires 2 each. Ford Cars 1955-68 Bumper, glovebox door check arm stop.
Body Hole Plug
p/n: 20-1040-21
Plug, hole in dog leg cover. Installs at front of door where bolt to adjust vent window frame is located. This body plug covers a sheet metal hole that is one and one half (1-1/2) inch in diameter.
Body Hole Plug
p/n: 20-1039-21
Plug, cowl and floor pan. This body plug covers a sheet metal hole that is one and one fourth (1-1/4) inch in diameter.
5/16" Glovebox Door Bumper
p/n: 33-0128-88
This 5/16" Glovebox Door Bumper is designed from the original part for superior fitment, finish and function. This bumper is commonly used as a glovebox door bumper on GM models.