This Convertible Roof Rail Weatherstrip Set fits on the folding roof of the vehicle and seals the side window when the window is fully raised.
This four (4) piece Front Door Vent Window Set contains the main vent window seals and division post seals. All of the pieces were designed from original parts for a precise, factory fit.
This Window Felt Weatherstrip is an Original equipment style side window horizontal seal kit (also known as beltline weatherstrip). Eight (8) piece kit includes inner and outer felt beltline weatherstrip for each door and quarter windows.
These Front Door Vent Window Weatherstrips are the main seals needed to replace the rubber on your vent windows. They are designed and molded from original parts for superior fitment and seal.
Boot, 3-speed manual transmission lower shifter. Exact reproduction of original. Surrounds shifter housing sealing out dirt, moisture and noise.
Boot, 4-speed manual transmission lower shifter. Exact reproduction of original. Surrounds shifter housing sealing out dirt, moisture and noise.
This Hinge Pillar Weatherstrip attaches to the body and seals between the A-pillar post and the front section of the door or vent window frame when the door is closed. Includes attaching screws.
Mount, upper motor. HiPo "289". Doughnut type.
This Door Weatherstrip pair is designed from the original parts for superior fitment and seal. This part is the primary door to body weatherstrip. Contains four (4) pins.
This Windshield Gasket mounts around the full perimeter of the front glass and has properly molded corners for a precise, factory fit.
This thirty-two (32) piece Body Plug and Grommet set is designed from the original parts for superior fitment and sealing. Mustang Club of America (MCA) approved.
This Spring Shackle Bushing Set is for the rear of the rear leaf spring. Two (2) sets required per car.
This Peel-N-Stick Trunk Lid Weatherstrip is designed for superior fitment and seal. The weatherstrip mounts around the full perimeter of the trunk lid to seal directly to the body. Easy to install 3M Peel-N-Stick backing provides superior adhesion for reliable performance.
Hose, air conditioner drain. Attaches to hole in floor.
Side window vertical leading edge weatherstrip.
This Accelerator Pedal Pad is made of top-quality EPDM rubber with a high level of fit and finish. Designed to be a direct fit reproduction.
Insulator, steering column lower flange.
This Trunk Lid Weatherstrip is designed from the original part for superior fitment and seal. The weatherstrip mounts around the full perimeter of the trunk lid.
Seal kit, front fender splash shields. Includes attaching staples. Six (6) piece kit.
Seals, top of vent window to door glass. Includes rivets.
This Quarter Window To Body Post seals pair are designed from the original parts for superior fitment and sealing. These seals are located on the quarter post to window.
Seal, power brake booster push rod to firewall.
Gasket, "Shelby" rotunda bullet mirror.
Grommet, steering column to floor interior side.
Bumper, center rear axle. Mounts on floor pan.
This Door To Window seals pair are designed from the original parts for superior fitment and sealing. These seals are located on the rear edge of the front door to window. Seals may also be known as a door jamb seals.
This Radiator Support To Hood Weatherstrip is designed from the original part for superior fitment and seal. This rubber weatherstrip fits at the front of the vehicle to seal between the radiator and the hood when hood is closed. Includes OE type staples to install.
This Air Cleaner Lid gasket is designed from the original part for superior fitment and sealing. This cut-to-fit gasket glues to the air cleaner lid to seal between the lid and air filter element housing. This gasket is for Six (6) Cylinder engine models.
This Air Cleaner Lid gasket is designed from the original part for superior fitment and sealing. This cut-to-fit gasket glues to the air cleaner lid to seal between the lid and air filter element housing. This gasket is for 289-302 V8 engine models.
Hose, fuel tank to filler pipe.
Bumper, outer rear axle. Mounts on frame rail. Push in type. Two (2) required per car.
Seal, lower ball joint dust.
Front vent window division post seal. Fully molded with metal core and attaching tabs.
This eleven (11) piece Front Stabilizer Bar End Link Kit is designed from original parts so it fits correctly. Two (2) kits / sets required per car as one (1) kit / set services one side of front stabilizer bar.
This Hood to Cowl weatherstrip is designed from the original part for superior fitment and seal. This seal mounts at the rear of the engine bay directly to the body. Includes attaching clips pre-installed.
This Quarter Panel Drain Plug pair is a quality reproduction of the original factory part. These rubber plugs fit inside the quarter panel area to seal-out weather and environmental elements.
This bumper is made from high-quality EPDM dense rubber for the Builder’s creative application and use.
This Radiator Support to Hood Bumper is a quality replacement for the original factory part. This adjustable bumper attaches to the radiator support to cushion / stop the hood closure. Usually requires two (2) front bumpers each per vehicle.
Upper Control Arm Bumper made with top quality rubber. Includes nut.
Plugs, seat access hole plugs. (Included in complete rubber plug kits). Eight (8) piece set.
Pads, parking light to body.
Grommet, valve cover (Positive crankcase ventilation valve). Used in round hole with two notches. Fits either aluminum or steel valve covers.
Bumper, door window lower stop. Installs inside door.Qty Required:2 Two (2) required per car.
Seals, back up light to body. Black.
Grommet, air conditioner hoses through firewall. Used with reproduction hoses. Has bigger holes than original.
Cover, headlight dimmer switch rubber.
Gaskets, pony interior door light.
Bumpers, trunk lid.
Grommet, air conditioner hoses through firewall. Used with original hoses.
Grommet, antenna lead-in. For front mount type.