PCV valve grommet
p/n: 20-2696-20
Grommet, valve cover (Positive crankcase ventilation valve). Used in round hole on steel valve covers.
Door or Tailgate Bumper
p/n: 33-1228-71
This Door Bumper is fully molded and designed from the original part for superior fitment. This rubber bumper attaches to the vehicle body to support / cushion the door closure. Usually requires two (2) bumpers each per vehicle.
Hood To Cowl Weatherstrip Bumper
p/n: 70-1251-42
This Hood To Cowl Weatherstrip Bumper is a quality reproduction of the original factory part. One fourth (1/4") of an inch high.
Hood To Cowl Weatherstrip Bumper
p/n: 70-1252-42
This Hood To Cowl Weatherstrip Bumper is a quality reproduction of the original factory part. Five sixteenths (5/16") of an inch high.
Accelerator Pedal Rod Seal
p/n: 20-2745-41
This Accelerator Pedal Rod Seal is used when running the accelerator rod through the firewall. The seal helps to block out air and wind noise from entering into the cabin.
Accelerator Pedal Rod Firewall Grommet
p/n: 20-2744-41
This Accelerator Pedal Rod Firewall Grommet is used to run the accelerator pedal rod through the firewall. Designed from original part so it fits correctly.
Clutch or Brake Pedal Bumper
p/n: 20-1051-24
This Clutch or Brake Pedal Bumper is designed from the original part for superior fitment, finish and function. This bumper is commonly used as a clutch or brake pedal arm stop cushion.
Standard Bumper
p/n: 20-0001-88
This Standard Bumper pair is designed from the original part for superior fitment and function. This rubber bumper fits ashtray or glovebox doors.
Cowl Top Plug
p/n: 20-1813-20
This Cowl Top Plug is designed from the original part for an authentic fit, finish, and appearance. This plug installs in the access hole in cowl top.
Tailgate Latch Striker Bumper
p/n: 70-1911-87
This Tailgate Latch Striker Bumper is a quality reproduction of the original factory part. This rubber bumper attaches to the station wagon tailgate to cushion its closure. Usually requires two (2) bumpers each per vehicle.
Body Hole Plug
p/n: 20-1041-21
Plug, cowl and floor pan. This body plug covers a sheet metal hole that is one and one seven eighths (1-7/8) inch in diameter.
3/4" Door Bumper
p/n: 33-0293-71
Bumper, front door pillar, upper and lower. Replaces factory #3720168.
1" Floor Pan Grommet
p/n: 35-0515-20
This Floor Pan Grommet is fully molded and designed from the original part for superior fitment and seal. This grommet is made from high-quality EPDM dense rubber to provide excellent durability.
Steering Column At Floor Seal
p/n: 70-3768-88
This Steering Column At Floor Seal is designed from the original part for superior fitment and sealing. Seal is machine die cut from sponge rubber to original specifications for a factory it. This part fits around the steering column to seal the column through the body floor pan.
Tailgate Bumper
p/n: 20-0888-45
These Tailgate Bumpers are designed from original parts for a correct fit. Sold as a pair.
Brake Pedal Pad
p/n: 20-1043-22
This reproduction Brake Pedal Pad slips over the full perimeter of the brake pedal for a precise, factory fit. Replaces original brake pedal pad for models with manual transmission and manual drum (not disc) brakes.
2" Firewall Grommet
p/n: 60-0707-20
This Firewall Grommet is used to run the body wiring harness at the engine bulkhead through the firewall. Special design for this usage.
Shock Absorber Grommet
p/n: 60-0235-33
This Shock Absorber Grommet is fully molded and designed from the original part for superior fitment and durability. The grommet the plain cylinder type with flat ends for shock absorber mounting.
5/16” Round Top Hood Bumper
p/n: 20-2755-42
This Hood Bumper pair is a quality reproduction of the original factory part. This rubber bumper attaches to the front radiator support to cushion / bump stop the hood closure.
5/8" Door Weatherstrip without Clips
p/n: 70-1111-73
This Door Weatherstrip made from high-quality EPDM sponge rubber. Excellent for use on many different vehicle models. Available by the foot.
Hood to Fender Bumper
p/n: 40-0503-42
Bumper, hood to fender ledge. Correct original cross-section. Up to ten (10) required per car.
Fuel filler cover bumper
p/n: 20-0006-41
Bumpers, fuel tank door. Single stem and double retainer bumper set.
Tailgate Bumper
p/n: 70-1609-87
This Tailgate Bumper is a quality reproduction of the original factory part. Made of a high-quality EPDM rubber, the bumper attaches to the vehicle body to support / cushion the tailgate closure.
Hood to Fender Bumper
p/n: 70-1630-42
This Hood to Fender Bumper is a quality reproduction of the original factory part. These rubber bumpers attach to the front fender to support / cushion the hood closure. Four (4) to six (6) required per vehicle.
Stabilizer Link or Shock Grommet
p/n: 70-0737-33
This Stabilizer Link or Shock Grommet is designed from the original part for superior fitment and usage. Fully molded rubber.
Gearshift Seal
p/n: 20-2875-88
Seal, automatic transmission shifter housing to floor. Installs between housing and floor pan.
2-1/4" Body Hole Plug
p/n: 35-0863-45
This Body Hole Plug is fully molded and designed from the original part for superior fitment and seal. Designed for the trunk, however the generic shape makes this plug usable for a variety of applications.
Instrument Bezel To Bezel Glass Seal
p/n: 70-4941-88
This Instrument Bezel To Bezel Glass Seal is designed from the original part for superior fitment and seal. This part seals the glass to the Instrument Panel / Bezel.
13/16" Door Weatherstrip without Clips
p/n: 70-1244-73
This Door Weatherstrip is made from high-quality EPDM sponge rubber. Excellent for use on many different vehicle models. Available by the foot.
Hood to Fender Bumper
p/n: 70-1963-42
This Hood to Fender Bumper is a quality reproduction of the original factory part. These rubber bumpers attach to the front fender to support / cushion the hood closure.
1" Trunk Weatherstrip
p/n: 70-0510-85
This Trunk Weatherstrip was designed from an original part for a specific application but has many uses outside of its original purpose. Available by the foot.
Hood Bumper
p/n: 70-1608-42
This Hood Bumper is a quality reproduction of the original factory part. These rubber bumpers attach to the front fender to support / cushion the hood closure.
3/4" Door Weatherstrip
p/n: 70-0236-73
This weatherstrip was designed for 1964–1966 Chevrolet and GMC truck doors but with its generic shape, has many uses outside of its original purpose.
Accelerator Pedal Rod Seal
p/n: 20-0128-41
This Accelerator Pedal Rod Seal is used to wrap around the accelerator rod linkage at the firewall. Designed from original part so it fits correctly.