Door Bumper
p/n: 33-1227-71
This Door Bumper is fully molded and designed from the original part for superior fitment. The twin retainer style rubber bumper attaches to the vehicle body to support/cushion the door closure. Usually requires two (2) bumpers each per vehicle.
Door Bumper
p/n: 70-3035-71
This Door Bumper is designed from the original part and attaches to door with single screw. Typically requires two (2) or four (4) bumpers per vehicle depending on the vehicles year of manufacture.
Door Bumper
p/n: 20-0067-71
This Door Bumper is designed from the original part for an authentic fit, finish and function. Installs on back edge of door. Usually two (2) to eight (8) per vehicle.
Door Bumper
p/n: 70-2045-71
This Door to Body Bumper is quality reproduction of the original factory part. Use varies depending upon model and body type. Some models uses four (4) bumpers for front doors and four (4) for rear doors.
Door Bumper - Lower
p/n: 70-1605-71
This fully molded Door Bumper is quality reproduction of the original factory part. This rear of door lower bumper attaches to the vehicle body to support / cushion the door closure.
Door Bumper - Lower
p/n: 70-3308-71
This Lower Door Bumper is designed from the original part for superior fitment and function. Bumper pushes into slot on door at bottom.
Door Bumper Set
p/n: 90-0209-90
This four (4) piece Door Bumper Set is designed from the original part for superior fitment, finish and function. Molded from top quality EPDM dense rubber to ensure durability.
Door Center Post Weatherstrips
p/n: 70-0847-73
This four (4) piece Door Center Post Weatherstrip set is designed from the original part for superior fitment and seal. A four (4) piece set for the left and right, front and rear doors. Authentic cross-section and construction.
Door Conduit Set for Power Windows
p/n: 60-0653-21
This Door Conduit Set is designed from the original part for superior fitment and function. Conduit contains the front door electric window wires and/or power lock vacuum lines. Set includes two (2) hoses and three (3) pair of grommets. Length: 12.0 inches.
Door drain hole seal
p/n: 70-3034-70
Seal, door inner panel drain. Attaches to bottom of door with one (1) carrot retainer on either end.
Door Glass Bumper
p/n: 20-1172-71
This lower door glass bumper is designed from the original part for superior fitment. If your door window goes too low, or makes a metallic sound when lowered all the way down, you likely need to replace this lower door glass bumper.
Door Glass Run Channel
p/n: 70-4313-58
This Door Glass Run Channel is designed from the original part for superior fitment and seal. The window glass run channel presses into the door channel at the top and back part of the door. This single piece fits either the driver (LH) OR the passenger (RH) side front door.
Door Handle Gasket Set
p/n: 70-0733-69
This Door Handle Gasket Set is designed from the original part for superior fitment and seal. This six (6) piece gasket set will do two (2) doors.
Door Handle Gasket Set
p/n: 60-0640-69
This Door Handle Gasket Set is designed from the original part for superior fitment and seal. This six (6) piece gasket set will do two (2) doors.
Door or Tailgate Bumper
p/n: 33-1228-71
This Door Bumper is fully molded and designed from the original part for superior fitment. This rubber bumper attaches to the vehicle body to support / cushion the door closure. Usually requires two (2) bumpers each per vehicle.
Door to Body Conduit, Power Window Wiring
p/n: 70-1538-70
This Door to Body Conduit set is designed from the original part for superior fitment and function. This is the sheathing conduit for the power windows wiring from the front door to the body through the hinge pillar.
Door To Window Seals
p/n: 20-2835-79
This Back of Door To Window seals pair is designed from the original part for superior fitment and sealing. These seals are located on the rear edge of the front door to window. Seals may also be known as a door jamb seals.
Door Vent Window Weatherstrip Set
p/n: 60-0577-55
This four (4) piece Door Vent Window Weatherstrip Set contains the main vent window seals and division post seals. All of the pieces were designed from original parts for a precise, factory fit.
Door Weatherstrip
p/n: 40-0489-73
Weatherstrip, door. Note: Order part #70-2592-73, end cap fillers separately.
Door Weatherstrip
p/n: 70-1832-72
Door edge weatherstrip with molded ends. This part is the primary door to body weatherstrip. Includes clips for easy installation. Made of top quality rubber.
Door Weatherstrip - Rear Door Striker Seal
p/n: 70-3296-73
This Rear Door Lock Striker Weatherstrip attaches to the front edge of rear suicide door to seal the gap where the front and rear doors meet. The seal has a brass metal core the full length of part.
Door weatherstrip end cap
p/n: 70-2592-73
Weatherstrip, door seal end cap or filler. Fully original molded type with metal core. Order perimeter weatherstrip #40-0489-73 separately.
Door Weatherstrip End Caps
p/n: 70-2053-79
This Door Weatherstrip End Caps filler pair is designed from the original part for superior fitment and seal. Fully molded with metal core.
Door Weatherstrip Fastener
p/n: 50-0198-73
This Door Weatherstrip Fastener is steel with a black finish. Each push-in fastener measures one half (1/2") inch long with a thirteen thirty second (13/32") inch diameter head. Reproduction fastener is designed from the original part to fit correctly.
Door Weatherstrips
p/n: 20-2826-72
This Door Weatherstrip pair is designed from the original parts for superior fitment and seal. This part is the primary door to body weatherstrip. Contains four (4) pins.
Door Weatherstrips
p/n: 20-1380-72
This front Door Weatherstrip pair is the primary door to body weatherstrip. Contains plastic pins that are attached to the door weatherstrips and molded ends with metal cores.
Door Weatherstrips - Convertible
p/n: 70-3930-72
This Door Weatherstrip is the primary door to body weatherstrip. Designed off original parts, the pair comes with the proper molded ends for a like factory fit.
Engine light grommet
p/n: 60-0706-17
Grommet, engine compartment light wire in lid. Not a universal grommet, this part is dimensionally just like the original.
Engine Mount - Lower
p/n: 20-1004-11
This left or right Lower Engine Mount is designed from the original part for superior performance and correct fitment. For 221, 260, 289 or 289 Hi-Po V-8 engines.
Engine Mount Service - Revulcanization Only
p/n: 70-1890-11
This Engine Mount - Revulcanization is designed to restore your original engine mounts to a like new condition. Service requires your metal cores. Please call or email for more service details and ordering.
Engine Mount Service - Revulcanization Only
p/n: 70-2008-11
This Revulcanization Service Only is designed to restore your Engine Mount pair to a like new original condition. Service requires your metal cores. Please call or email for more service details and ordering.
Engine Mount Service – Revulcanization Only
p/n: 60-0624-11
This Revulcanization Service Only is designed to restore your Rear Engine Support Mount to a like new original condition. Service requires your metal core. Please call or email for more service details and ordering.
Engine Mount Service – Revulcanization Only
p/n: 70-2597-11
This Revulcanization Service Only is designed to restore your Front Lower Engine Support Mount to a like new original condition. Service requires your metal core. Please call or email for more service details and ordering.
Engine Mount Service – Revulcanization Only
p/n: 70-1891-11
This Revulcanization Service Only is designed to restore your Engine Support Mount to a like new original condition. Service requires your metal core. Please call or email for more service details and ordering.
Exhaust Tailpipe Hanger Strap
p/n: 60-0308-13
This Exhaust Tailpipe Hanger Strap is made from high-quality rubber for a precise, factory like fit for your classic vehicle. Muffler/tailpipe system, reproduction strap type is manufactured to OEM specifications.
F-100 Brake OR Clutch Pedal Pad
p/n: 70-4484-22
This reproduction F-100 script Brake OR Clutch Pedal Pad slips over the full perimeter of the brake or clutch pedal for a precise, factory fit. Replaces original brake or manual transmission clutch pedal pads.
Fastback Fold Down Rear Seat To Floor Stop Bumpers
p/n: 20-2884-88
This Fastback Fold Down Rear Seat To Floor Stop Bumper pair is designed from the original part for superior fitment, finish and function. Includes jamb nuts.
Fender Skirt Edge Weatherstrip
p/n: 70-1606-44
This Fender Skirt Edge Weatherstrip pair is designed from the original part for superior fitment, finish, and seal. This weatherstrips fits between the rear wheel fender skirt and the rear fender quarter panel.
Fender Skirt Edge Weatherstrip
p/n: 40-0476-44
This Fender Skirt Edge Weatherstrip pair is designed from the original part for superior fitment, finish, and seal. This weatherstrips fits between the rear wheel fender skirt and the rear fender quarter panel.
Fender Skirt Edge Weatherstrips
p/n: 20-0061-44
This Fender Skirt Edge Weatherstrip pair is designed from the original part for superior fitment and seal. This weatherstrip fits between the rear quarter panel wheel opening and the fender skirt.
Fender To Hood Side Cushion Bumper
p/n: 70-2610-42
This Fender To Hood Side Cushion Bumper is a quality reproduction of the original factory part. This rubber bumper attaches to the front fender to support / cushion the hood closure. Usually requires four (4) bumpers each per vehicle.
Fender to Radiator Seal
p/n: 20-1101-45
This two (2) piece Fender to Radiator Seal is designed from the original part for superior fitment and seal. Installs between the front fender and the radiator support.
Fender Welting
p/n: 20-1591-44
This black Fender Welting is designed from the original part for superior fitment and seal. This welting material fits between the fenders and the vehicle body. Eight (8) foot length.
Firewall Accessory Wiring Grommet
p/n: 27-0100-20
This Firewall Accessory Wiring Grommet is designed from the original part for superior fitment and function.