Rear Leaf Spring Shackle Assembly
p/n: 20-1066-32
This reproduction Rear Leaf Spring Shackle Assembly is complete with shackle bar plates, rubber bushings and lock nuts. For fitting the suspension leaf spring at its rear spring eye to the vehicle body. Two (2) assemblies required per car.
Convertible Top Rail Drains
p/n: 20-1157-67
This Convertible Top Rail Water Drain pair is designed from the original part for superior fitment and function. The part fits on the convertible top rail at the rear as a water drain.
Convertible Top Pads
p/n: 20-1158-67
This Convertible Roof Top Pad pair is designed from the original part for superior fitment and function. The part fits at the top of the rear quarter window on the roof.
Accelerator Pedal Pad
p/n: 20-1075-40
This Accelerator Pedal Pad is made of top-quality EPDM rubber with a high level of fit and finish. Designed to be a direct fit reproduction.
Front Fender to Cowl Seal
p/n: 20-1100-45
This two (2) piece Front Fender to Cowl Seal pair is designed from the original part for superior fitment and seal. These seals are also known as lower extension seals.
Front Fender Dust Shield Filler
p/n: 70-3071-45
This six (6) piece Front Fender Dust Shield / Splash Apron set is designed from the original part(s) for superior fitment and seal. Filler pieces are die cut from quality masticated rubber to authentic original dimensions.
Trunk Weatherstrip
p/n: 20-0302-84
This Trunk Weatherstrip is designed from the original part for superior fitment and seal. The decklid weatherstrip mounts around the full perimeter of the trunk directly to the body.
Fender to Radiator Seal
p/n: 20-1101-45
This two (2) piece Fender to Radiator Seal is designed from the original part for superior fitment and seal. Installs between the front fender and the radiator support.
Voltage Regulator Cover Shield
p/n: 70-4531-17
This Voltage Regulator Cover Shield is designed from the original part for superior fitment and function. This cover shield is located over and above the voltage regulator.
Quarter Window Lock Piller Filler
p/n: 20-1194-79
This Quarter Window Lock Piller Filler pair is made from high-quality EPDM rubber for a precise, factory like fit. This filler pair seals the bottom of the rear side window and may also be known as a door jamb seal.
Front Engine Mount
p/n: 20-1001-11
Front motor mount support. Left-hand side only. Fairlane big block engines. See description for fitment.
Quarter Window Leading Edge
p/n: 20-1198-80
This Side Quarter Window Vertical Leading Edge Weatherstrip pair is designed from the original part for superior fitment and seal. This part attaches to the vertical edge of the rear side windows when the rear side windows are fully raised.
Clutch Lever Dust Boot
p/n: 20-2712-24
This Clutch Lever Dust Boot covers the opening on your engine bellhousing for manual transmission models. Made from Original Ford tooling.
Vent Window To Beltline Filler
p/n: 20-1192-73
This Vent Window To Beltline Filler pair is designed from the original part for an authentic fitment and appearance. Filler is the front of the door seal at beltline in front of vent window.
Taillight to Body Gaskets
p/n: 20-1019-15
This Taillight to Body Gasket pair is designed from the original part for superior fitment and seal. These reproduction gaskets fit between taillight frame housing and the body.
Division Bar Glass Run Channel
p/n: 20-1113-58
This Division Bar Glass Run Channel pair is designed from the original part for superior fitment and function. This glass run channel holds the glass in place.
Sound Deadener Underlayment Set
p/n: 70-4602-88
This five (5) piece die-cut Sound Deadener Underlayment Set lays under the carpet. This sound deadener will decrease road noise and decrease heat inside the interior compartment. Pre-cut and ready to be installed into your vehicle to improve driving comfort.
Hinge Pillar Weatherstrip
p/n: 20-1150-63
Convertible Hinge Pillar Weatherstrip - Attaches to the body and seals between the A-pillar post and the front section of the door or vent window frame when the door is closed.