This is an Original equipment style side window horizontal weatherstrip set (also known as beltline weatherstrip). This eight (8) piece anti-rattler set includes inner and outer window felt beltline weatherstrips for each side and quarter window.
Made from Standard material. Side window horizontal seal (also known as beltline weatherstrip). These strips wipe the side windows when the glass is lowered.
This two (2) piece Vent Window Weatherstrip Set (pair) fits both driver and passenger doors of the vent window assemblies.
Door edge weatherstrip. This part is the primary door to body weatherstrip. Contains plastic pins that are attached to the door weatherstrips and molded ends with metal cores. Also contains ten (10) plastic clips for the molded ends.
This two (2) piece Division Bar Glass Run Channel pair installs between the front of door glass and the back of the vent window.
Hardtop roof rail weatherstrip. This part fits on the roof of the vehicle and seals the side window when the window is fully raised.
Pads, taillight bezel to body.
This eight (8) piece Hood Bumper set is designed from the original parts for superior fitment and function.
Bumper, front suspension lower arm.
This Front Fender Apron Dust Shield pair is designed from the original part for superior fitment and function. Filler shield pieces are die cut from quality masticated rubber to authentic original dimensions.
This Quarter Window U Jamb Lock Pillar Filler pair is designed from the original part for superior fitment and sealing. This part seals the bottom of the rear side window, and may also be known as a door jamb seal.. Fully molded authentic rubber construction with metal core.
This Side Window Vertical Leading Edge Weatherstrip pair is designed from the original part for superior fitment and seal. This part attaches to the vertical edge of the rear side windows when the rear side windows are fully raised.
Seals, cowl side panel to fender. Includes fasteners.
Kit, cowl lacing.
This Trunk Weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the trunk directly to the body.
Mount, rear engine support on transmission.
This two (2) piece Splash Apron / A-Arm Dust Shield Filler pair is designed from the original part for superior fitment and seal. Filler pieces are die cut from quality masticated rubber to authentic original dimensions. Left and Right pieces fit over suspension a-arms and inside front inner fenders.
Pads, headlight door. Gray rubber.
Pedal, accelerator. Molded rubber design. Trucks (F100-200) after Serial #696,001.
Insulator, steering column lower flange.
This Air Deflector piece is designed from the original part for superior fitment and seal. Piece is die cut from quality masticated rubber to authentic original dimensions. This piece fits at the bottom of radiator core support to frame. Used on V8 models.
Seal, top of radiator support to hood air deflector. Fifty (50) inches long. For the following engines: 240, 289, 352, 390, 427, or 428.
Gaskets, back-up light lens
Gaskets, parking light lens.
Pad, radiator mounting. Upper.
Pad, radiator mounting. Lower.
Pad, parking brake pedal.
Shields, parking light splash.
Bumper for front suspension upper arm. Measures three eighths (3/8) inch by sixteen (16) by eleven sixteenths with (11/16) inch bolt thread.
Gaskets, taillight lens to housing.
Grommets, headlight wiring through radiator support. Requires one (1) per car.
Bumper, hood on fender. Push-in type. Three fourths (3/4) inch wide. Four (4) piece set.
This four (4) piece Rear Bumper Arm Seal set installs between the body and rear bumper. A reproduction designed from original part so it fits correctly.
Seal, accelerator pedal linkage to firewall.
Bumper, hood on rear of fender. Rubber button tip only. Two (2) piece set.
Seal, radiator side air deflector.
Insulator, front coil spring.
This Quarter Panel Drain Plug pair is a quality reproduction of the original factory part. These rubber plugs fit inside the quarter panel area to seal-out weather and environmental elements.
This Radiator Support to Hood Bumper is a quality replacement for the original factory part. This adjustable bumper attaches to the radiator support to cushion / stop the hood closure. Usually requires two (2) front bumpers each per vehicle.
Seal, radiator side air deflector. One and five eighths (1-5/8) inch by twelve and one half (12-1/2) inch.
Bumper, ash tray door.
Grommet, antenna lead-in. For front mount type.
Bumper, rear license plate rubber. One (1) required per car.
Plug, cowl and floor pan. This body plug covers a sheet metal hole that is one and one seven eighths (1-7/8) inch in diameter.
Pad, trunk lock cylinder sleeve. Three (3) lug cylinder type.
Bumper, door. Installs on back edge of door. Please check your car for quantities required.Usually two (2) to eight (8) per vehicle.
Stop, glovebox arm.Ford Truck 1957-64 Stop, glovebox arm. Requires 2 each. Ford Cars 1955-68 Bumper, glovebox door check arm stop.
Plug, cowl and floor pan. This body plug covers a sheet metal hole that is one and one fourth (1-1/4) inch in diameter.
Plug, hole in dog leg cover. Installs at front of door where bolt to adjust vent window frame is located. This body plug covers a sheet metal hole that is one and one half (1-1/2) inch in diameter.
Plug, cowl and floor pan. Three fourths (3/4) inch.