This bumper is made from high-quality EPDM dense rubber for the Builder’s creative application and use.
Gasket, air cleaner lid. Cut to fit.
Gasket, air cleaner lid. Cut to fit.
Hose, air conditioner drain. Attaches to hole in floor.
Gasket, left-hand air vent outlet.
Grommet, antenna lead-in. For front mount type.
Bumper, outer rear axle. Mounts on frame rail. Push in type. Two (2) required per car.
Bumper, center rear axle. Mounts on floor pan.
Gaskets, back-up light lens.
Seals, back up light to body. Black.
Plugs, seat access hole plugs. (Included in complete rubber plug kits). Eight (8) piece set.
Plug, cowl and floor pan. Three fourths (3/4) inch.
Plug, cowl and floor pan. This body plug covers a sheet metal hole that is one and one fourth (1-1/4) inch in diameter.
Plug, cowl and floor pan. This body plug covers a sheet metal hole that is one and one seven eighths (1-7/8) inch in diameter.
Plug, hole in dog leg cover. Installs at front of door where bolt to adjust vent window frame is located. This body plug covers a sheet metal hole that is one and one half (1-1/2) inch in diameter.
Plug kit, complete rubber. Includes quarter drain valves and installation instructions. MCA approved. Thirty two (32) pieces.
Pad, front fender to body pillar. Two (2) required per car.
Bumper, brake and clutch pedal arm.
Pads, front bumper bracket to fender. Two (2) required per car.
Bumpers, door. Push in type.Qty Required:4 Four (4) required per car.
This Door To Window seals pair are designed from the original parts for superior fitment and sealing. These seals are located on the rear edge of the front door to window. Seals may also be known as a door jamb seals.
Door edge weatherstrip. This part is the primary door to body weatherstrip. Contains four (4) pins.
Grommet, air conditioner hoses through firewall. Used with original hoses.
Grommet, accelerator pedal rod firewall.
Grommet, air conditioner hoses through firewall. Used with reproduction hoses. Has bigger holes than original.
This front door vent window weatherstrip kit is a four (4) piece set that contains the main vent window seals and division post seals. All of the pieces were designed from original parts for a precise, factory fit.
These front door vent window weatherstrips are the main seals needed to replace the rubber on your vent windows. They are designed and molded from original parts for superior fitment and seal.
This eleven (11) piece Front Stabilizer Bar End Link Kit is designed from original parts so it fits correctly. Two (2) kits / sets required per car as one (1) kit / set services one side of front stabilizer bar.
Grommets, fuel line to side apron.
Gasket, fuel neck to body.
Hose, fuel tank to filler pipe.
Boot, 4-speed manual transmission lower shifter. Exact reproduction of original. Surrounds shifter housing sealing out dirt, moisture and noise.
Boot, 3-speed manual transmission lower shifter. Exact reproduction of original. Surrounds shifter housing sealing out dirt, moisture and noise.
Seal, automatic transmission shifter housing to floor. Installs between housing and floor pan.
Bumpers, glovebox and/or license plate. Used as glove box door bumpers for 65-66 and 71-73 models, used as license plate bumper for 65-70 models.
Stop, glovebox arm.Ford Truck 1957-64 Stop, glovebox arm. Requires 2 each. Ford Cars 1955-68 Bumper, glovebox door check arm stop.
Hardtop roof rail weatherstrip for coupe models. Includes fasteners. This part fits on the roof of the vehicle and seals the side window when the window is fully raised.
Cover, headlight dimmer switch rubber.
Bumper, hood on fender.1965-66: Mustang (4 required). 1967-68: Mustang (2 required).
Hood Bumper, radiator support hood. Includes jamb nut. Vulcanized "Rounded Top" type. Two (2) required per car.
This Hood to Cowl weatherstrip is designed from the original part for superior fitment and seal. This seal mounts at the rear of the engine bay directly to the body. Includes attaching clips pre-installed.
Seal, radiator support to hood. Includes original type attaching staples.
Gaskets, pony interior door light.
Gasket, rear license light lens.
Mount, upper motor. HiPo "289". Doughnut type.
Gaskets, parking light lens.
Pads, parking light to body.
Grommet, valve cover (Positive crankcase ventilation valve). Used in round hole on steel valve covers.
Grommet, valve cover (Positive crankcase ventilation valve). Used in D-shaped hole on steel valve covers.
Grommet, valve cover (Positive crankcase ventilation valve). Used in round hole with two notches. Fits either aluminum or steel valve covers.