Search Results
Front Door Vent Window Kit
p/n: 90-0348-90
This front door vent window weatherstrip kit is a four (4) piece set that contains the main vent window seals and division post seals. All of the pieces were designed from original parts for a precise, factory fit.
Front Door Vent Window Weatherstrips
p/n: 70-2595-55
These front door vent window weatherstrips are the main seals needed to replace the rubber on your vent windows. They are designed and molded from original parts for superior fitment and seal.
Power window conduit
p/n: 70-1538-70
Conduit for power window wiring from front door to body through hinge pillar.
Splash Apron / A-Arm Dust Shield Kit
p/n: 70-2498-45
This eight (8) piece Splash Apron / A-Arm Dust Shield set is designed from the original part for superior fitment and seal. Filler pieces are die cut from quality masticated rubber to authentic original dimensions. Pieces fit over suspension a-arms and inside front inner fenders.
Beltline Weatherstrip
p/n: 70-0961-60
Weatherstrip, inner beltline. Thick pile lined, without chrome bead. Available in 4ft pairs.
Vent Window Division Post Run Channel
p/n: 70-0985-58
The front door side window glass run channel on the backside of the vent window division post. Flock lined with a molded-in upper bumper.
Motor (Engine) Mounts
p/n: 70-1006-11
Motor (Engine) Mounts, front engine support pair. Height: 3.375 inches.
Auxiliary beltline seal
p/n: 70-3301-73
Seal, auxiliary at beltline. Seal fits at beltline on hinge pillar.
Vent division bar weatherstrip
p/n: 70-2596-56
Front vent window division post seal. Fully molded with metal core and attaching tabs.
Front bumper seal filler
p/n: 70-2505-45
Filler, front bumper to radiator seal. Die cut masticated rubber to authentic original dimensions. Includes all factory style holes required for installation.
Beltline Weatherstrip
Weatherstrip, outer beltline. For use on front, rear, and quarter windows without a chrome reveal molding at the window beltline. Available in a 3ft pair and 6ft piece.
Window Sash / Beltline Channel
p/n: 70-0651-58
Rigid, rubber covered weatherstrip with flock lining and one fourth (1/4) inch chrome edge. Available in a 6ft piece.
Front Stabilizer Bar End Link Kit
p/n: 70-2111-33
Kit, front stabilizer bar link assembly replacement. Twenty-two (22) piece set. One (1) kit for both sides of one (1) car. Hex head bolt. 3/8"-16nc x 7-1/2" long. Comes with metal sleeve, metal cup washers and rubber grommets.
Peel-N-Stick Trunk Weatherstrip
p/n: 70-0773-WT
This trunk weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the trunk directly to the body. Easy to install 3M Peel-N-Stick backing provides superior adhesion for reliable performance.
Trunk Weatherstrip
p/n: 70-0773-84
This trunk weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the trunk directly to the body.
Beltline Weatherstrip
Window felt inner. Rigid, flocked rubber lip, with flat stainless bead. Available in 2ft and 3ft pairs.
Battery clamp cover
p/n: 70-0095-21
Cover, battery clamp. Control unsightly sulfate buildup. Help protect the nearby metal and finish. Good copy from original part.Length: 3.5 inches.
AC condenser mount
p/n: 70-0964-31
Mount, air conditioning condenser. Four (4) used per car.Length: 1.0 inches. Width: .75 inches.
Masticated rubber sheet
p/n: 70-0645-45
Masticated sheet. Three thirty seconds (3/32) inch thick rubber sheet containing random milled cotton cord reinforcement for front end splash aprons, etc. This product is a four (4) foot wide roll, and will only be sold in four (4) square foot multiples
Instrument panel grommet
p/n: 70-1654-88
Grommet, instrument panel to windshield frame. Two (2) to six (6) required.Length: 1.3125 inches. Width: 1.0625 inches.
Headlight dimmer switch pad
p/n: 70-0930-14
Pad, headlight dimmer switch. Rubber slip-over cover for floor mounted switch.
Trunk lock emblem gasket
p/n: 70-0875-86
Gasket, trunk lock emblem escutcheon. Steel rule die cut rubber of exact profile.Width: 1.875 inches. Height: 1.9375 inches.
Door Weatherstrip w/ Clips (Sponge Rubber Extrusion - General Use)
p/n: 70-1245-73
Door edge weatherstrip made from high quality EPDM sponge rubber. Excellent for use on many different vehicle models. Available by the foot.
2-5/8" Run Channel Mohair Liner
p/n: 70-2863-58
Run channel liner helps reline guide bars on lock side of hardtops and convertibles. Available by the foot.
Peel-N-Stick Trunk Weatherstrip
p/n: 70-0510-WT
Peel-N-Stick Trunk Weatherstrip made from high quality EPDM sponge rubber. Available by the foot.
Trunk Weatherstrip
p/n: 70-0346-85
Designed from an original part for a specific application but has many uses outside of its original purpose. Available by the foot.
Door Weatherstrip w/o Clips (Sponge Rubber Extrusion - General Use)
p/n: 70-1244-73
Door edge weatherstrip made from high-quality EPDM sponge rubber. Excellent for use on many different vehicle models. Available by the foot.
Trunk Weatherstrip
p/n: 70-0510-85
Designed from an original part for a specific application but has many uses outside of its original purpose. Available by the foot.
1/4" Universal mounting pad
p/n: 70-0308-17
Mounting pad, continuous for lights, hinges, brackets, and other bright work when no molded pad is available. Available by the foot.
Body hole plug
p/n: 35-0863-45
Plug, body sheet metal holes. Used in various places (like trunks). For one and one half (1-1/2) inch hole in body.
Door Weatherstrip w/o Clips (Sponge Rubber Extrusion - General Use)
p/n: 70-1111-73
Door edge weatherstrip made from high-quality EPDM sponge rubber. Excellent for use on many different vehicle models. Available by the foot.
Stabilizer or shock grommet
p/n: 70-0737-33
Grommet, front stabilizer link or shock absorber. Fully molded rubber. One and one eighths inch (1 1/8") by three eighths inch (3/8") inside hole diameter by seven eighths inch (7/8") height. Use as a front stablizer link for 1946-1970 Cadillac: All mode
Hood bumper
p/n: 70-0991-42
Bumper, hood to fender ledge. Typically four (4) to six (6) used per car.Length: 1.15625 inches. Width: .3125 inches.
Hood Bumper
p/n: 70-1251-42
Bumper, hood to cowl weatherstrip, one fourth (1/4) inch high. For three sixteenths (3/16) inch high see our #70-1250-42.
Hood Bumper
p/n: 70-1252-42
Bumper, hood to cowl weatherstrip, five sixteenths (5/16) inch high. For three sixteenths (3/16) inch high see our #70-1250-42.
1/16" Filler and Cushion Strip
p/n: 70-1236-48
Filler and cushion strip with a variety of applications. Available by the foot.
Door Bumper
p/n: 33-1227-71
Bumper, door edge, twin retainer style, three eighths (3/8) inch wide by seven eighths (7/8) inch long by three eighths (3/8) inch high.
