Rear stationary quarter window weatherstrip.
These front door vent window seals are designed from the original parts for superior fitment and seal. The pieces are molded as left and right and contain metal cores with attaching tabs that run vertically on the division post.
Rear door edge weatherstrip. This part is the primary door to body weatherstrip.
This tailgate weatherstrip is designed from the original part for superior fitment and seal. The seal mounts to the tailgate opening, directly to the body, with properly spaced plastic clips. Includes molded ends that contain brass cores.
Front door edge weatherstrip. This part is the primary door to body weatherstrip.
Leaf Spring Shackle Bushing Kit - For rear of rear leaf spring. Complete with shackle bars and bolt assembly with rubber bushings. Two (2) kits required per car.
Front Coil Spring Saddle Insulator Kit - Two front coil spring bushings and two spring insulators to restore the performance of your classic vehicle. Requires two (2) per car.
Seal, rear bumper to body.
Front motor mount support. Right-hand side only. Fairlane big block engines. See description for fitment.
Channel, flexible door window run. Stainless steel beaded. Available in 5ft lengths.
Front motor mount support. Left-hand side only. Fairlane big block engines. See description for fitment.
Weatherstrip, outer beltline. For use on front, rear, and quarter windows without a chrome reveal molding at the window beltline. Available in a 3ft pair and 6ft piece.
Plug kit, complete rubber. Includes quarter drain valves and installation instructions. MCA approved. Thirty-three (33) piece set.
Seals, front fender to radiator support. Staples included.
Kit, cowl lacing. Clips installed.
Window felt inner and/or outer. Flexible, pile lined, rubber covered, with black bead. Available in 2ft pair, 3ft pair, and 6ft piece.
Gaskets, taillight to body. For vehicles without reflectors.
This six (6) piece Front Fender Dust Shield / Splash Apron set is designed from the original part(s) for superior fitment and seal. Filler pieces are die cut from quality masticated rubber to authentic original dimensions.
Seals, rear of front fender to cowl upper.
Seals, rear of front fender to cowl side panel lower extension. Staples included.
Valves, rear floor pan extension drain.
Channel, door window glass lower rubber. Front or rear doors. One (1) pair does two (2) windows.
Rear Leaf Spring Bushing - Original style leaf spring bushings used in front eyes of rear leaf springs. Requires two (2) spring bushings per vehicle.
Window felt inner and/or outer. Flexible, pile lined, rubber covered, with black bead. Available in 2ft and 3ft pairs.
Pedal, accelerator. Includes chrome trim. Trucks (F100-350) before Serial # P60,001.
Drains, convertible top rail rear water.
Seals, headlight to fender. Gray rubber.
Seal, clutch pedal rod.
Pad, horn ring pressure.
Insulator, steering column lower flange.
Pad, brake pedal. Models with manual transmission and manual brakes.
Pad, brake pedal. Models with automatic transmission and manual brakes.
Seal, top of radiator to hood. Holes pre-punched and special fasteners included.
Pad, radiator mounting. Lower.
Insulator, gear shift.
Rear Leaf Spring Insulator Pad - An exact replacement of the rear spring center mount rubber insulator block that mounts below the leaf spring. Four (4) required per vehicle. Fits 2-1/2" leaf spring.
Bumpers, dual useage. Used on the rear of the hood for 1966-67: Fairlane & Ranchero. Used as a liftgate bumper for 1966-77: U-Series Bronco. Use on the door for 1967-72: F100-750 Series trucks.
Gaskets, air vent inlet duct to cowl.
Repair kit, stabilizer bar end. Eleven (11) piece set. Two (2) kits required per car. Hex head bolt. 3/8"-16nc x 6-7/8" lg. Comes with metal sleeve, four (4) cup washers and four (4) rubber grommets.
Seal, accelerator pedal rod.
Insulator, front coil spring upper.
Bumper, front suspension. Bumper section is 1-5/8" tall, 2" long, and 1-3/8 wide.
Gasket set, back-up light lens. Four (4) piece set.
This Steering Column is designed from the original part for superior fitment and sealing. Seal part is die cut from quality masticated rubber to authentic original dimensions. This part fits around the steering column to seal the column through the body floor pan inside the vehicle.
Gaskets, taillight lens. For vehicles without reflectors.
Hood Bumper, radiator support hood. Includes jamb nut. Vulcanized "Rounded Top" type. Two (2) required per car.
Plugs, quarter panel drain.
Bumpers, fender to hood. Used in top of fender. Four (4) piece set.
Gaskets, parking light lens.
Grommet, antenna lead-in. For front mount type.