Please click on the part name in red in order to get a complete description.
Vent Window Weatherstrip Set - This two (2) piece set (pair) fits both driver and passenger doors of the vent window assemblies. All of the pieces were designed from original parts for a precise, factory like fit.
Door edge weatherstrip. This part is the primary door to body weatherstrip. Contains plastic pins that are attached to the door weatherstrips and molded ends with metal cores. Also contains ten (10) plastic clips for the molded ends.
Channel, division bar glass run.
Hardtop roof rail weatherstrip. This part fits on the roof of the vehicle and seals the side window when the window is fully raised.
Hardtop roof rail weatherstrip. This part fits on the roof of the vehicle and seals the side window when the window is fully raised. Replaces factory #C7AZ-6351222-D.
Pads, taillight housing to body.
Side window vertical leading edge weatherstrip.
Bumper, front suspension lower arm.
Bumper kit, hood. Includes 1 set of C7AZ-16758-A, 1 set of C5AZ-16758-A and 1 set of C5ZZ-16763-B.
Seals, front fender apron to frame lower rear.
Door lock pillar seal. This part seals the bottom of the rear side window, and may also be known as a door jamb seal. Fully molded authentic rubber construction with metal core. Includes eight (8) metal screws.
This trunk weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the trunk directly to the body.
Plug kit, complete rubber. Includes quarter drain valves and installation instructions. MCA approved. Thirty-three (33) piece set.
Seals, cowl side panel to fender. Includes fasteners.
Kit, cowl lacing.
Mount, rear engine support on transmission.
Dust shield, A-arm.
Pads, headlight door. Gray rubber.
Ends, rear stone deflector rubber. One (1) pair per car.
Pedal, accelerator. Molded rubber design. Trucks (F100-200) after Serial #696,001.
Insulator, steering column lower flange.
Seal, bottom of radiator support to frame air deflector. Twenty and one fourth (20-1/4) inch by twenty nine and three fourths (29-3/4) inch.
Seal, radiator support to bottom of radiator. "L" shaped. Twenty six and three eighths (26-3/8) inches long.
Seal, top of radiator support to hood air deflector.
Gaskets, back-up light lens. Four (4) piece set.
Seal, radiator side air deflector. Four (4) inch by fourteen and one eighth (14-1/8) inch.
Seal, radiator side air deflector.
Seal, top of radiator support to radiator. Twenty four (24) inches long.
Pad, radiator mounting. Upper.
Pad, radiator mounting. Lower.
Pad, parking brake pedal.
Bumper for front suspension upper arm. Measures three eighths (3/8) inch by sixteen (16) by eleven sixteenths with (11/16) inch bolt thread.
Gaskets, taillight lens to housing.
Gaskets, parking light lens.
Bumper, hood on fender. Push-in type three fourths (3/4) inch wide. Four (4) piece set.
Bumper, hood on rear of fender. Rubber button tip only. Two (2) piece set.
Seal, radiator side air deflector.
Insulator, front coil spring.
Hood Bumper, radiator support hood. Includes jamb nut. Vulcanized "Rounded Top" type. Two (2) required per car.
Bumper, ash tray door.
Grommet, antenna lead-in. For front mount type.
Plug, cowl and floor pan. This body plug covers a sheet metal hole that is one and one seven eighths (1-7/8) inch in diameter.
Pad, trunk lock cylinder sleeve. Three (3) lug cylinder type.
Pad, trunk lock cylinder sleeve. Four (4) lug cylinder type.
Bumper, door. Installs on back edge of door. Please check your car for quantities required.Usually two (2) to eight (8) per vehicle.
Stop, glovebox arm.Ford Truck 1957-64 Stop, glovebox arm. Requires 2 each. Ford Cars 1955-68 Bumper, glovebox door check arm stop.
Plug, cowl and floor pan. This body plug covers a sheet metal hole that is one and one fourth (1-1/4) inch in diameter.
Plug, hole in dog leg cover. Installs at front of door where bolt to adjust vent window frame is located. This body plug covers a sheet metal hole that is one and one half (1-1/2) inch in diameter.
Plug, cowl and floor pan. Three fourths (3/4) inch.
Standard Bumper - Commonly used for fuel filler or glovebox doors.