Quarter Window Vertical Leading Edge
p/n: 83-1012-80
This quarter and side window Vertical Leading Edge Weatherstrip pair is designed from the original part for superior fitment and seal. A reproduction weatherstrip manufactured to OEM specifications to install for an authentic fit and finish.
Trunk Decklid Bumper Stop
p/n: 82-0160-87
This Trunk-Decklid Bumper Stop is a quality reproduction of the original factory part. This adjustable rubber bumper attaches to the vehicle body to support / cushion the trunk lid closure.
Hood Bumpers - At Cowl - Without Brackets
p/n: 20-0876-42
This Hood Bumper pair is designed from the original part for superior fitment. Bumpers mount at the cowl without brackets.
Stabilizer Bar End Link Repair Set
p/n: 20-1068-33
This eleven (11) piece Stabilizer Bar End Link Repair Set is designed to withstand harsh conditions without deteriorating. Two (2) end link sets required per car.
Back of Door to Window Seals
p/n: 20-2836-79
This Back of Door to Window Seal pair is for the bottom of the rear side window. Part may also be known as a door jamb seal(s). Fully molded authentic rubber construction with metal core.
Hood bumper
p/n: 20-0875-42
Bumpers, hood side. 1967-69 needs 1 pr. per truck, 1970-72 needs 2 pr. per truck.
Splash Apron / A-Arm Dust Shield
p/n: 70-3335-45
This two (2) piece Splash Apron / A-Arm Dust Shield Filler set is designed from the original part for superior fitment and seal. Filler pieces are die cut from quality masticated rubber to authentic original dimensions. Pieces fit over suspension a-arms and inside front inner fenders.
AC Condenser Mount
p/n: 70-0964-31
Mount, air conditioning condenser. Four (4) used per car.Length: 1.0 inches. Width: .75 inches.
Hood to Cowl Weatherstrip
p/n: 70-2807-43
This Hood to Cowl Weatherstrip is designed from the original part for superior fitment and seal. This seal mounts at the rear of the engine bay directly to the body.
Clutch Lever Dust Boot
p/n: 70-4760-24
This Clutch Lever Dust Boot covers the opening on your engine bellhousing for manual transmission models. A reproduction manufactured to OEM specifications to install for an authentic fit, finish and function.
Stabilizer Bar Bushings
p/n: 70-4678-34
This Stabilizer Bar to Frame Bushing pair may fit either front or rear stabilizer / sway bars depending on the vehicle. Manufactured with quality materials to original specifications.
Cornering Light Lens Gaskets
p/n: 70-3100-17
This Cornering Light Lens Gasket pair is designed from the original part for superior fitment and seal. These quality reproduction gaskets fit between the cornering light lens and the cornering light housing or bezel.
Splash Apron / A-Arm Dust Shield Filler
p/n: 70-2798-45
This Splash Apron / A-Arm Dust Shield Filler pair is designed from the original part for superior fitment and seal. Filler pair pieces are die cut from quality masticated rubber to authentic original dimensions. This filler pair fits over suspension a-arms and inside front inner fenders.
Brake or Clutch Pedal Pad - Manual
p/n: 60-0709-22
A top-quality rubber Clutch or Brake Pedal Pedal Pad reproduction. One (1) each slip-over type pedal pad installs over the full perimeter of the brake or clutch pedal for a precise, factory fit. For manual transmission model GM vehicles only.
Hood to Cowl Weatherstrip
p/n: 70-4095-43
This Hood to Cowl weatherstrip is designed from the original part for superior fitment and seal. This seal mounts at the rear of the engine bay directly to the body.
Front Axle Bumper
p/n: 20-1577-33
This Front Axle Bumper is a quality reproduction of the original factory part. These bottoming bump stops are dense rubber blocks that mount with a stud to a front axle bracket.
Firewall to Hood Weatherstrip
p/n: 70-3465-42
This Firewall to Hood Weatherstrip is designed from the original part for superior fitment and seal. An exact reproduction of the original profile made in sponge rubber. This weatherstrip installs at the rear of the engine bay to seal between the hood and the vehicle firewall.
Rear Leaf Spring Insulator
p/n: 20-2733-32
This Rear Leaf Spring Insulator is an exact replacement of the rear spring center mount rubber insulator block that mounts below the leaf spring. Four (4) required per vehicle. Fits 2-1/2" leaf spring.
Quarter Panel Drain Valves
p/n: 20-2770-45
These Quarter Panel Drain Valves are constructed of a durable rubber and are a direct-fit replacement. This product is sold as a pair.
Fastback Fold Down Rear Seat To Floor Stop Bumpers
p/n: 20-2884-88
This Fastback Fold Down Rear Seat To Floor Stop Bumper pair is designed from the original part for superior fitment, finish and function. Includes jamb nuts.
Splash Apron / A-Arm Dust Shield Filler
p/n: 70-3062-45
This two (2) piece Splash Apron / A-Arm Dust Shield Filler pair is designed from the original part for superior fitment and seal. Filler pieces are die cut from quality masticated rubber to authentic original dimensions. Left and Right pieces fit over suspension a-arms and inside front inner fenders.
Brake Pedal Pad - Manual w/Disc Brakes
p/n: 70-4803-22
This reproduction Brake Pedal Pad slips over the full perimeter of the brake pedal for a precise, factory fit. A direct fit to replace worn, heavy wear original brake pedal pads. For models with manual transmission and disc brakes.
Rocker Panel Inner Drain Cover
p/n: 70-2392-45
This Rocker Panel Inner Drain Cover pair is designed from the original part for superior fitment and seal. Fully molded with proper attaching teeth and flap.
Splash Apron / A-Arm Dust Shield Filler Set
p/n: 70-3309-45
This five (5) piece Splash Apron / A-Arm Dust Shield Filler set is designed from the original part for superior fitment and function. Filler pieces are die cut from quality masticated rubber to authentic original dimensions.
Brake Pedal Pad
p/n: 20-1044-22
Pad, brake pedal. Models with automatic transmission and manual brakes.
Battery Clamp Cover
p/n: 70-0095-21
This Battery Clamp Cover helps to protect the nearby metal and finish. Fully molded from high-quality EPDM rubber to ensure durability. Good copy from an original part.
Kick Panel Hole Cover
p/n: 70-4536-45
This Kick Panel Hole Cover is designed from the original part for superior fitment and function. Cover is made from high-quality EPDM 80 durometer dense rubber to provide excellent durability and service.
Taillight Lens Gaskets
p/n: 70-3772-15
This Taillight Lens Gasket pair is designed from the original part for superior fitment and seal. These reproduction gaskets fit between taillight lens & taillight housing.
Stabilizer Bar End Link Set
p/n: 60-0221-33
Twenty-two (22) piece Stabilizer Bar End Link set for both sides of one (1) vehicle, fits front or rear bar. Order two (2) sets for vehicles with front and rear stabilizer bars. Hex head bolt 3/8"-16 NF x 6-15/16" long. Comes with metal sleeve, metal cup washers and rubber grommets.
Fuel Tank Mounting Isolator Set
p/n: 70-4628-41
This six (6) piece Fuel Tank Mounting Isolator Set is a reproduction of the original style fuel tank isolator set. Replacing or adding the isolator strips and pads can help eliminate noise or friction between the fuel tank straps and the body.
Radiator Side Air Deflector
p/n: 20-0192-31
This Radiator Side Air Deflector pair is designed from the original part for superior fitment and function. Left and Right seals are die cut from correct 3/32" masticated rubber to authentic original dimensions. Mounts to core support at side of radiator with included hardware.
Fuel Filler Neck Grommet
p/n: 70-1439-39
This Fuel Filler Neck Grommet is designed from the original part for superior fitment and seal. This grommet fits around the vehicles fuel filler neck between the filler neck and vehicle body. Fits as original.
Steering Column Grommet
p/n: 70-3158-36
This Steering Column Grommet is designed from the original part for superior fitment and seal. This seal fits around the steering column at the toe board.
Clutch or Brake Pedal Pad
p/n: 60-0712-22
This reproduction Clutch or Brake Pedal Pad pair slips over the full perimeter of the pedal for a precise, factory fit. A perfect reproduction to replace worn original pedal pads. Manufactured in quality black rubber.
Quarter Post To Door Window Seals
p/n: 20-2840-79
This Quarter Post To Door Window seal pair is designed from the original part for superior fitment and sealing. These seals are located on the quarter post to window.
Ulta-Mat Kick Panel Heat and Sound Underlayment
p/n: 70-4782-88
This Ulta-Mat Kick Panel Heat and Sound Underlayment is pre-cut for a direct-fit installation. Underlayment pieces are made from a flexible and lightweight foil facing foam rubber sound and heat insulation material.
Door Handle Gasket Set
p/n: 70-0733-69
This Door Handle Gasket Set is designed from the original part for superior fitment and seal. This six (6) piece gasket set will do two (2) doors.
Rally Sport Camaro Paint Gasket Supplement Set
p/n: 82-0225-44
This six (6) piece Rally Sport Camaro Paint Gasket Supplement set contains the RS specific parking light and reverse light gaskets. These die cut foam reproductions are designed from originals for superior performance, durability and a factory fit.
Splash Apron
p/n: 20-0879-44
This two (2) piece Splash Apron pair is designed from the original part for superior fitment and seal. Fasteners included. This is a front fender to hood hinge support seal.
Engine Top Cover Weatherstrip
p/n: 70-3531-88
This Engine Top Cover Weatherstrip is an original design reproduction made from top quality sponge rubber. This gasket attaches between the removable engine cover ("doghouse") and the vehicle firewall/floorboard.
Hood to Fender Bumper
p/n: 70-2046-42
This Hood to Fender Bumper pair is a quality reproduction of the original factory part. These rubber bumpers attach to the front fender to support / cushion the hood closure.
Rear spring bushing
p/n: 20-0661-32
Bushing, rear spring front and rear. Useage: 1964-66: F250 4x2's- 4 required 1966: F250 4x4's and all 350's- 2 required 1966-69- Bronco
Rear Leaf Spring Insulator
p/n: 70-0980-32
This Rear Leaf Spring Insulator is an exact replacement for the upper and lower spring pad. Two and one half (2-1/2) inches wide, with cloth reinforcement. Four (4) used per car.
Radiator Upper Mount Insulators
p/n: 20-2716-31
This Radiator Upper Mount Insulator pair is a quality reproduction of the original factory part. These rubber insulators fit between the Radiator Upper Mounting brackets and the radiator.
Radiator Lower Mount Insulators
p/n: 20-2718-31
This Radiator Lower Mount Insulator pair is a quality reproduction of the original factory part. These rubber insulators fit between the Radiator Lower Mounting brackets and the radiator.
Trunk Decklid Weatherstrip
p/n: 20-2858-84
This Trunk Deckid Weatherstrip is designed from the original part for superior fitment and seal. The weatherstrip mounts around the full perimeter of the trunk lid.
Door Bumper
p/n: 70-3035-71
This Door Bumper is designed from the original part and attaches to door with single screw. Typically requires two (2) or four (4) bumpers per vehicle depending on the vehicles year of manufacture.
Splash Apron / A-Arm Dust Shield
p/n: 70-3500-45
This two (2) piece Splash Apron / A-Arm Dust Shield Filler set is designed from the original part for superior fitment and seal. Filler pieces are die cut from quality masticated rubber to authentic original dimensions. Pieces fit over suspension a-arms and inside front inner fenders.
Paint Gasket Set
p/n: 82-0026-44
This comprehensive nineteen (19) piece Paint Gasket Set includes the major seals and gaskets when painting or restoring a classic Camaro. These reproduction parts are designed from originals for superior performance, durability and a factory like fit.
Air Deflector - At Radiator Core Support
p/n: 20-0193-31
This Air Deflector piece is designed from the original part for superior fitment and seal. Piece is die cut from quality masticated rubber to authentic original dimensions. This piece fits at the bottom of radiator core support to frame. Used on V8 models.
Splash Apron / A-Arm Dust Shield
p/n: 70-3067-45
This two (2) piece Splash Apron / A-Arm Dust Shield Filler set is designed from the original part for superior fitment and seal. Filler pieces are die cut from quality masticated rubber to authentic original dimensions. Pieces fit over suspension a-arms and inside front inner fenders.
Window Locking Strip - Black
p/n: 70-2195-52
This extruded Locking Strip is used to retain windshield gaskets in pickups and vans. Designed from the original part for superior fitment, finish and function. Available in 16ft lengths.
Brake and Clutch Pedal Pads
p/n: 70-3003-22
This reproduction Clutch and Brake Pedal Pad pair slips over the full perimeter of the brake pedal for a precise, factory fit. A square style direct fit reproduction to replace worn original pedal pads. Manufactured in black rubber.
Radiator Top Seal
p/n: 20-0194-31
Seal, radiator support to bottom of radiator. "L" shaped. Twenty six and three eighths (26-3/8) inches long.
Fender Welting
p/n: 20-1591-44
This black Fender Welting is designed from the original part for superior fitment and seal. This welting material fits between the fenders and the vehicle body. Eight (8) foot length.
Firewall to Hood Weatherstrip - Cowl Lacing
p/n: 20-1088-42
This Firewall to Hood Weatherstrip is designed from the original part for superior fitment and seal. An exact reproduction of the original profile. This single piece cowl lacing seal mounts at the rear of the engine bay to seal between the hood and vehicle body cowl / firewall.
Clutch or Brake Pedal Pad
p/n: 60-0467-22
This reproduction Clutch or Brake Pedal Pad pair slips over the full perimeter of the pedal for a precise, factory fit. A perfect reproduction to replace worn original pedal pads. Manufactured in quality black rubber.
Splash Apron / A-Arm Dust Shield
p/n: 70-3058-45
This two (2) piece Splash Apron / A-Arm Dust Shield Filler set is designed from the original part for superior fitment and seal. Filler pieces are die cut from quality masticated rubber to authentic original dimensions. Pieces fit over suspension a-arms and inside front inner fenders.
Firewall to Hood Weatherstrip - Cowl Lacing
p/n: 20-0790-42
This Firewall to Hood Weatherstrip is made of high quality EPDM dense rubber and to the original design for a factory like fit and appearance. Comes with pre-drilled mounting holes and mounting clips installed.
Hood to Cowl Weatherstrip
p/n: 70-3924-43
This Hood to Cowl Weatherstrip has the proper rubber cross section and is made from top quality rubber to ensure durability and seal. Designed from the original part for a superior fitment and seal.